Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2

See what our Experts say about this etrailer Trailer Bearings Races Seals Caps

• Replacement Bearings and Seals for Lippert 4,400 Lb Axle
  The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part # BK2-100 or just the Grease Seal part # RG06-050.
  view full answer...
• Replacement Rotors and Calipers Needed for a 2003 Mastercraft Single Axle Boat Trailer
  To determine the correct Hub and Rotor for your 2003 Mastercraft single axle boat trailer you will need to determine what the inner and outer bearing part numbers are inside the hub, the brake mounting flange bolt pattern and the correct bolt pattern for your wheels. In my experience the Mastercraft boat trailers have an integrated hub and rotor that utilizes oil bath seals and caps. The integrated hub and rotor would need to be removed and a new hub and rotor would be needed to replace...
  view full answer...
• What is the Inner and Outer Diameter of the 10-19 Double Lip Seals
  The double lip seal has an inner diameter of 1.719 inches and an outer diameter of 2.565 inches. The seal used in bearing kit # BK2-100, are also sold in pairs, # RG06-050. I have also included a link to the bearing kits we offer. To determine the correct bearing kit or replacement parts, you will need to retrieve the inner and outer bearing numbers stamped in the metal of the bearings. The grease seal fits inside the hub bore, so the outer diameter is important.
  view full answer...
• Replacement Seals And Hubs For Boat Trailer W/ 3500lb Axles And Oil Bath Hub and Rotors
  There are special seals to convert your 3500lb rotors to oil bath, and they can be replaced with Replacement Seal For 3500-lb Axles # XLPROLUBE1980SEAL. While we do not offer 9-3/4" rotors for your 3500lb boat axle, we do have the Dexter 10" Hub-and-Rotor Assembly # K08-435-05 which measures 10" in diameter, and is designed for 3500lb axles. This rotor uses inner bearing # L68149, outer bearing # L44649, and grease seal # RG06-050(you will not need the grease seal as you will need the...
  view full answer...
• Replacement Race and Grease Seal for Trailer Bearing # L44649
  If you are talking about the race or cup as it is sometimes called, you would use # L44610. But if you are talking about the seal then it will either be a 10-19, # RG06-050, with inner diameter of 1.719 inches and outer diameter of 2.565 inches; or it will be a 10-60 seal, # RG06-020, with 1.500 inch inner diameter and 1.987 inch outer diameter. We also have various spindle washers if that is what you mean. I have linked them for you.
  view full answer...
• Trailer bearings and Seals For Lippert 3500 Lb Axle on Jayco Jay Flight
  Since the axle in the photo is a Lippert 3,500 lb axle the bearings you need are part # L68149 for the inner and part # L44649 for the outer. You need part # RG06-050 for the seals. You can remove your existing hub to check the bearing numbers stamped on the side of the bearing to double check but these are the most common bearings and seals used on that axle. You can also use the kit part # BK2-100 that comes with the cotter pin and tang washer. If you are looking for your bearing numbers...
  view full answer...
  
• Replacement Bearings, Races, Seals, Brake Drums and Brake Assemblies for 4400 lb Axle
  The spindles used on the 4400 axle are compatible with the # L67048 Inner bearing and # LM67010 race and the # L44649 Outer bearing and # L44610 race, along with the 10-19 grease seal, part # RG06-050. You'll want to confirm this by pulling one of the hubs to check the reference numbers off of your current bearings. For brakes, you'd need a 10 x 2-1/4 inch brake assembly. I'd recommend a Nev-r-adjust assembly, part # K23-478-479 for the right and left sides. Typically, it's recommended...
  view full answer...
• Replacement Bearings and Seal for a #84 Spindle
  From the measurements you gave me I believe you need the bearings # L44649, # L68149, and the replacement seal # 58846 (which is available in a pack of 2 with part # RG06-050). All of this is available in the kit # BK2-100 which is for a #84 spindle.
  view full answer...
• Recommended Disc Brake Conversion For Tandem Axle Boat Trailer With 13 Inch Wheels
  We don't have a kit for 13 inch wheels, but I can give you all the components you need. For your rotor/hubs, you will need 2 of the Kodiak Disc Brake Kit - 8" Rotor/Hub - 5 on 4-1/2 - Dacromet - 3,500 lbs # K2HR35D-8. This will require 4 of the # L68149 bearings, 4 of the # L44649 bearings and 2 of the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2 # RG06-050. Then you will need the tandem brake lines, and I recommend the Kodiak Hydraulic Brake Line Kit...
  view full answer...
• Replacement Hub Recommendation for Trailer with L44649 Bearings, and L44649 and L68149 Bearings
  For your trailer hub that has bearing numbers # L44649 and a bolt pattern of 5 on 4-1/2 inch the trailer hub part # AKIHUB-545-2-1K that you referenced would be the correct hub. It comes with the correct grease seals as well. For additional seals though you'd need the part # 10-9. For a replacement spindle you'd want the part # TRU44FR. If you need a wheel and tire we have the Kenda 4.80-12 Bias Trailer Tire with 12" White Spoke Wheel - 5 on 4-1/2 # AM30660 which matches the size tire and...
  view full answer...
• How to Identify Replacement Grease Seal on Trailer
  There are a few different ways you could find out the correct replacement grease seal for your trailer. One is to contact the manufacturer. Assuming they are still in business they should be able to tell you what grease seal was used. If that doesn't work, you could identify the axle and hubs assuming these are original parts. Axle capacity can also be a good indicator, but depending on the manufacturer it may not follow the standards. For example, if you have a 3,500 lb axle it probably...
  view full answer...
  
• Replacing Bearings, Races, and Seals for Hub with L68149 and L44643 Inner/Outer Bearings
  The outer bearing you have, # L44643, is very close in size to bearing # L44649. These two bearings fit different size spindles. So in other words the larger L44649 bearing would be very loose on the spindle that normally takes the L44643. Measure the diameter of the spindle where the outer bearing sits using some digital or dial calipers. If the measurement is 1 inch then L44643 that you have is correct. This bearing is typically found on 2,000 pound axles but not 3,500 pound axles. We...
  view full answer...
• Correct Spare Hub and Drum For 2014 Airstream 23D With 3000lb Dexter Axle
  Thanks for the picture of your axle tag! Based on the information my contact at Dexter was able to pull from the axle tag your 2014 Air Stream 23D uses a hub with inner bearing # L68149, outer bearing # L44649, and grease seals # RG06-050. For a spare hub there are a few different options based on your bolt pattern. The Trailer Hub and Drum Assembly - 3.5K E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 - Pre-Greased # AKHD-655-35-EZ-K you were looking at has the less common 6 on 5-1/2" bolt...
  view full answer...
  
• Replacement Brake Assembly and Grease Seal for AL-KO T44 Axle
  For your AL-KO T44 axles, the brake assemblies you need are the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4.4K # K23-478-479 or the manual adjust # K23-462-463-00 along with spoon adjuster # W80630. The grease seal you want is AL-KO part 568861 which is the Grease Seal - Double Lip - ID 1.719" / OD 2.565" # RG06-050 for a set of 2 seals.
  view full answer...
  
• Are Grease Seals RG06-050 a Direct Replacement for Timken Seals 171255
  You are correct, the Grease Seals 10-19 pair, part # RG06-050, are the direct replacement for the Timken seals 171255. You can view some additional information on replacing trailer hub components at the links provided.
  view full answer...
• Recommended Spare Parts To Replace UFP Hubs With Rotors And Calipers
  We don't have the UFP Brand, but I can give you some compatible parts. For your trailer hubs with rotor, I recommend the Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs # KHR10D. You will need grease seal # RG06-050 along with bearing # L68149 and # L44649. For your brakes, I recommend the Kodiak Ceramic Brake Pads w/Stainless Steel Backing Plate - 3,500 lbs to 6,000 lbs # K225CPSS along with the Kodiak Disc Brake Caliper - Stainless Steel - 3,500 lbs to 6,000 lbs...
  view full answer...
• How to Identify Which Replacement Bearing Kit for Keystone Passport 151 Ultra Light Travel Trailer
  You do have a Dexter axle, but I don't have enough information to provide specific replacement parts. What appears in your photo looks more like a catalog than an owner's manual. Dexter offers many different axles in the 600-8000 lb range, all of which would use different bearing sets. Unfortunately, there isn't a database that would allow me to look up which bearings your axle uses, but I can make a pretty good guess which you'll want to confirm. Given the 3885 GVWR you very likely have...
  view full answer...
  
• Grease Seal for Haulmark Trailer TSR85X20WT2 with 3,500 lb Axle
  I was able to find that your Haulmark trailer TSR85X20WT2 has 3,500 lb axle so for a hub seal you'd want the # RG06-050.
  view full answer...
• Replacement Trailer Bearings for Shoreland’r Trailer with #84 Spindle
  Based off the measurements you provided, you've got a #84 spindle, so the correct bearings are the # L44649 and # L68149, and # RG06-050 grease seals. We typically try to put bearing numbers of popular manufacturers on the bearing pages but those are Shoreland'r part numbers so they're not on the product pages currently. You can get these in a complete kit with the Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal # BK2-100
  view full answer...
• Recommended Replacement Seal For A Tri Tec T-23972 Seal
  Though I may have an option for you, I was also unable to find any info on the T-23972 seal you currently have. With that being said, the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2 # RG06-050, or # 58846 as just a single seal, is very close to your measurements. These can warp over time, which could be the cause of the differences. One way to confirm if these are correct or not will be to check your inner bearing as well. This seal will be used on 3,500...
  view full answer...
• How to Pick Out Replacement Hub Seal for Trailer Axle
  Are you looking for the grease seal or the dust cap? Since you said inner that makes me think you need a seal which we can help with if you can take a couple measurements. To pick out a replacement grease seal you will need to measure the diameter of the spindle where the grease seal rides with a digital or dial caliper and then need to measure the hub bore where the current seal rides. With those two dimensions we can pick out the correct seal that you would need. I attached a link...
  view full answer...
• Which Grease Seal Comes with Dexter Trailer Hub Assembly - 3,500-lb Axles - 5 on 4-1/2 - E-Z Lube
  EZ lube hub # 84545UC1-EZ includes a 10-19 grease seal. Take a look at # RG06-050, which is a pair of the same size. the cross reference chart indicates it is a replacement for Transcom 171255TB. The 10-19 has an inner diameter of 1.719 inches and an outer diameter of 2.565 inches. The outer diameter fits the hub and the inner diameter fits the spindle.
  view full answer...
• Parts Needed To Add Hydraulic Disc Brakes To Trailer
  To add hydraulic disc brakes to your trailer you will need a few parts. For a hub and rotor assembly I recommend the Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs # K2HR35D which will allow you to use your 14" wheels and bolts to your 4 bolt brake flange. You will need to confirm that your spindles use inner bearing # L68149 and outer bearing # L44649, but since all of our 14" wheel options use those bearings this should be the kit you need. You will need inner...
  view full answer...
• Replacement Grease Seal for 2020 Grand Design Imagine XLS 22RBE
  From what I have found, the GVWR of your 2020 Grand Design Imagine XLS 22RBE is 6,995 lbs. Based on that information, you more than likely have 3,500 lb axles. The most common grease seal for a 3,500 lb axle is the # 58846 with a 1.719" inner diameter and 2.565" outer diameter. For a pair you would need the # RG06-050. This is strictly based on your typical 3,500 lb axle. Ultimately there is no way to be sure without identifying the axle or the part number on the grease seal. If you are...
  view full answer...

Do you have a question about this Trailer Bearings Races Seals Cap?