Grease Seal for Haulmark Trailer TSR85X20WT2 with 3,500 lb Axle

Question

Question:

I have a 2005 Haulmark 20 enclosed Race Trailer, model # TSR85X20WT2. Im trying to find axle hub seals so I can service my trailers wheel bearings. Can you advise if you folks carry them? Thanks.

asked by: Michael J

1

Helpful Expert Reply:

I was able to find that your Haulmark trailer TSR85X20WT2 has 3,500 lb axle so for a hub seal you'd want the # RG06-050.

expert reply by: Jameson C

1

Answer 1

The Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-468-469 is our best option for a 3,500 lb trailer axle. They are self-adjusting, made in the USA, and come with a five year warranty. You can mix self-adjusting and manual adjusting braking…

view full answer...

Answer 2

Although we don't have a way to tell right off hand what bearings and seal your axle has, if you pull your hub there should be part numbers on your bearings and seal. Let me know what those are and I can help you out. If you cannot find the part…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Jeffrey. Sweet, you have a Lippert 3,500lb axle. It looks like this axle already has a brake mounting flange installed. This is going to allow you to add all the braking components without replacing the axle. The parts you're going to need in…

view full answer...

Answer 12

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Grease Seal for Haulmark Trailer TSR85X20WT2 with 3,500 lb Axle

Product Page this Question was Asked From

Continue Researching