Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
(568 reviews)
Price: $98.23
In Stock
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
Item # AKHD-545-35-EZ-K
Our Price: $98.23
Orders above $99 qualify for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (568)
- Q & A (0)
- Photos
etrailer by AxleTek Trailer Hubs and Drums - AKHD-545-35-EZ-K
- 5 on 4-1/2 Inch
- For 3500 lbs Axles
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Hub with Integrated Drum
- 1/2 Inch Stud
- Easy Grease
- EZ Lube
- Pre-Greased
- etrailer
Hub-and-drum assembly for your trailer. For electric or hydraulic brakes. Fits 3.5K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.
Features:
- Trailer hub-and-drum assembly provides surface area for brake shoes to grip when brake is activated
- Compatible with electric and hydraulic drum brakes
- Dexter E-Z Lube and etrailer Easy Grease-compatible grease cap makes lubricating bearings fast and easy
- Remove rubber plug to access zerk fitting on spindle - no need to disassemble hub
- Sturdy iron construction
- Zinc-enriched paint on drum adds durability
- Zinc-finished bolts resist corrosion
- Pre-greased hub-and-drum assembly is easy to install - no need to pack bearings
- Lithium complex, multipurpose grease keeps bearings lubricated
- Bearings, races, grease seal, grease cap, and lug nuts are included
- QAI and CSA certified
Specs:
- Application: 3,500-lb Dexter E-Z Lube and etrailer Easy Grease trailer axles with #84 spindles
- Compatible with standard axles from most manufacturers, including Dexter, Lippert (LCI), and AL-KO
- Actual drum dimensions: 10" diameter x 2-1/2" wide
- Works with 10" brake assembly
- Bolt pattern: 5 on 4-1/2"
- Wheel studs: 1/2" diameter x 1-1/4" long
- Grease cap flange diameter: 1.99"
- Weight capacity: 1,750 lbs
- Limited 1-year warranty
Bearing, Race, and Seal Information
- Bearings (included)
- Inner bearing: L68149 (1.378" inner diameter)
- Outer bearing: L44649 (1.063" inner diameter)
- Races (included)
- Inner race: L68111
- Outer race: L44610
- Grease seal (included): 58846
- Inner diameter: 1.719"
- Outer diameter: 2.565"
Thoroughly Tested for Safety
This hub-and-drum assembly meets the requirements for certification by the Canadian Standards Association (CSA). The CSA creates standards, which when complied with ensure a safe and quality product. This assembly underwent extensive testing to measure stopping distances when braking. This assembly has also been tested by QAI for braking performance in a complete automotive setup and under real-world conditions to provide the most realistic scenario for the everyday driver.
E-Z Lube and Easy Grease-Compatible Assembly for Simple Lubrication
The grease cap on this hub-and-drum assembly is specially designed to work with your Dexter E-Z Lube or etrailer Easy Grease axle to make lubricating bearings quick and easy. Just remove the plug on the grease cap, attach a grease gun to the zerk fitting on the end of the spindle, and inject the grease. It will flow easily to both inner and outer bearings. Not only does this make lubricating the bearings easy, but it also helps to prevent corrosion of the hub. This is because you can lubricate the bearings without the mess of taking apart the entire assembly.
Determining the Bolt Pattern
The first number in the bolt pattern is the number of bolt holes. The second number denotes the diameter, in inches, of the circle on which the bolt holes sit.
On wheels with an even number of bolt holes, measure from the center of one bolt hole to the center of the hole directly across from it. (Example: 8 on 6-1/2 means 8 bolt holes with 6-1/2" from the center of one hole to the center of another on the opposite side.)
To determine the bolt-circle diameter on wheels with an odd number of bolt holes, measure from the center of any bolt hole to the point halfway between the two bolt holes directly across from the first. (Example: 5 on 4-1/2 means 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolt holes.)
Measuring the distance (D) from the center of one bolt hole on the wheel to the center of a bolt hole right next to it can also help to determine the bolt pattern.
- If D = 2-5/8", then the bolt pattern is 5 on 4-1/2"
- If D = 2-3/4", then the bolt pattern is 5 on 4-3/4"
- If D = 3", then the bolt pattern is 5 on 5"
- If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
KBD2-545-19 AxleTek 10" Trailer Hub and Drum Assembly for 3.5K Axle with Hardware - 5 on 4-1/2 - EZ Lube - Pre Greased
Compare to Dexter 84546UC3-EZ
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
- Product did not meet expectations
Customer Reviews
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased - AKHD-545-35-EZ-K
Average Customer Rating: 4.7 out of 5 stars (566 Customer Reviews)
Hub-and-drum assembly for your trailer. For electric or hydraulic brakes. Fits 3.5K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.by: Roderick07/22/2023
Hubs matched to my original Dexter hubs. The prices was more than 50% less than Dexter axles; well worth the savings.
Bearings came installed; made installation a breeze. Slide them on and put on retaining washer, nut and retaining bracket.
I’d buy them again (today) will re-evaluate in a year.
by: Jess12/11/2023
This is the trailer I built using your spindles and electric brakes.
It towed beautifully from Texas to Kansas City and back for the World of Wheels.
by: Robert08/31/2022
Easily installed... Pre-greased bearing... Should have come with new axel nut, cotter key and bearing washer, but didn't.. Used old ones...
by: George07/15/2023
Purchased a used 2016 Keystone Hideout Trailer and wanted to be sure it was safe going down the road. These four assemblies were clean, packaged well and fit as expected. We will be headed out to campsite next month and will update this review ONLY if their is a discrepancy, otherwise, we are very satisfied with our etrailer purchase.
by: Marcus05/22/2024
Part are great. Shipping was quick and communication was great. No issues with the transaction. Minus one start for less than adequate packaging for transport. I’ve had two orders. The hub that came with other items was in a box in a box. The other items were just loose in the box without protection. No damage noted, but the potential is there depending on the handling practice. Hub that cam skin was in its own box. Appreciate the reduced number of boxes, but this wasn’t sufficient. No damage to the part, but the outside of the.hub poked through the box, the plastic was pulled out and shredded and the hi. Protective cap was damaged.
by: Jeffrey02/12/2024
Pleased with the quality of these hub/drum assemblies. Bearings were nicely pre-greased. Kit comes with solid bearing hub covers and bearing buddy types with removable rubber grease plugs...your choice.
by: Jeffery03/28/2024
One of the lug nuts was damaged and could not be used. I would like a cotter pin and a flat washer included in this assembly.
by: Donald 02/12/2024
I think your a great company but my hub drum assembly was a little out of round.
This is probably from storage by the manufacturer.
Have great day! Don
by: James 04/29/2024
Product replaced OEM part exactly. product was fully lubed as advertised. Installation was simple.
by: John03/28/2024
I haven't received my leaf springs at the same time. I ordered them within minutes of each other. So I have to wait until next week now. Once I get things together I can make an accurate assessment. Probably the only gripe of mine is that I have to wait now. Thanks for the follow up.
by: John 05/15/2024
Very good quality and easy to install I highly recommend this company for all your trailer needs
by: Shannon04/29/2018
I ordered the hub and idler set, my trailer came with 15x5 hubs and I ordered 15x4.5 rims. Since they wouldn't return my rims I ordered the correct hubs from etrailer. Got my box only had one seal slightly damaged. Installing was a breeze and happy with my purchase... Website was very user friendly as my first plan was to do a 6lug but I talked myself out of it. Thanks etrailer good job, nice company to deal with.
by: Lawrence11/11/2023
I ordered an easy grease trailer hub and drum assembly to replace the one on my 14 foot cargo trailer which was damaged by a defective magnet. The one I ordered fit perfectly. Since it came pre-greased, it saved quite a bit of time because I did not have to pack the bearings and press in the seal.
by: Buck.04/15/2024
Fast service. Help us work through getting good replacement parts. Thank you.
by: Mike06/03/2017
This is my second order. I ordered for the rear axle first. The parts looked good. So ordered for the other axle. The seals are robust and double seal design. But the bearing are China bearings. Would have liked to seen timkin or the like but are serviceable. The break kit fit well and looks good. We will see how they do on my 2500 mile round trip thru the mountains with a small truck loaded on it. The operators both times were very friendly and knowledgeable about their products. Keep up the good work and I'll keep buying!
Mike
6/3/2018
Put about 3000 miles with zero issues. They performed better than expected. I have ordered several items since then and the operators are all knowledgeable and all ways willing to do what they can to ensure a proper order and that Im satisfied with my order
by: Brian07/10/2023
Missing parts, one of the two kits I ordered was already opened an missing the caps
Rebecca N.
7/13/2023
It is a bummer that it arrived missing the grease caps. I will have our Customer Service team reach out to you.
by: Keith 03/20/2024
drums and brakes went together perfectly. Amy J was a big help.
by: Royce05/26/2024
i really do like it,good items pretty sturdy and price is good and super fast shipping A+++++++
by: Allen09/11/2023
Received the hubs very quickly. They were well greesed and ready to go. They look well machined. I did have one lug nut that had something wrong with the threads. I might could have used it, but since it would not thread on by hand I did not want to try it since it might damage the stud. I went on line and did a chat with etrailer. Thier customer service is top rated. They shipped me out another lug nut. This is why I do business with etrailer. They understand the needs of the customer and understand the products they sell.
I installed the hubs this weekend and took the trailer for a test pull. Needed to adjust the brakes up a little, but all was well.
by: Brian05/25/2024
your trailer selection and specifications were not right for my Forrest River. your site said it has 3.5 k axles but it really has 4 k which regulate different parts. i returned the parts and sent your prople the manufactures delivery sheet so you can update your site.
by: Albert B05/15/2024
13,737 miles to Fairbanks from Ft. Myers and bank, still going good.
by: David 02/07/2024
Service was great and the shipping was fast. As always etrailer out performs its competitors.
by: Walter 07/23/2023
Perfect fit for the corresponding e-trailer brake assembly. Even comes with lug nuts, but I didn’t use them because they are a size up from whats on the rest of my trailer wheels. Same thread, just different lug wrench size. Personally, e-trailer, I’d forgo including the lug nuts and instead, include the mounting hardware with your e-trailer brake assemblies.
by: Jimmy 05/09/2024
Great product
by: Jimmy 05/03/2024
Love these hubs
25
568
Show More Reviews
See what our Experts say about this etrailer Trailer Hubs and Drums
- Replacement Parts Available for etrailer 3,500 lb Trailer AxleFor the etrailer axle part # e95SR we do have replacement hub/drums with part # AKHD-545-35-EZ-K, and for brake assembly set # AKEBRK-35, for brake shoes # AKBRKR-S-10, and magnet # AKBRKR-M10.
view full answer... - Replacement Axle Suspension System for 2010 Keystone Hideout 26RLSWEThank you for the photo and the "SC = 68.50" means you have a spring-center to spring-center length of 68-1/2 inches and the "D35" means the axle is rated for 3,500 lbs. While we do not carry any axles with those specifications we do have a great solution, the Timbren Axle-Less Trailer Suspension System. These are really an improvement over a traditional through-axle because they offer you an improved ride. They work independently (as opposed to an axle which is connected by a beam) so...
view full answer...
- Tips for Removing Races from a Trailer Hub and Drum AssemblyAre you replacing the races in the hub? I ask because the hubs and hub and drum assemblies we sell come with the races already installed so you would not have to reuse the old ones. Races are difficult to remove but since you have one out already you can go into the opposite side from the race still in the hub and use a wooden rod to drive out the race. I do not recommend using any metal tool (unless it was designed for this application), only wood, because if the inner surface of the...
view full answer... - Do Different Timbren Axle-Less Suspension Systems Have the Same Camber and Ride HeightThe caster and camber could be the same on the # TASR35HDS03 and # ASR2KHDS05. The system has a slight manufacture camber. However, it is up to you on how much camber you have based on the installation. This can be changed using the included shims. As far as the ride height is concerned, these do not have the same dimensions. This will result in a different height between the systems when installed. The # TASR35HDS03 will also stick out farther. Since there is no real advantage to using...
view full answer... - Recommended Hub Drum and Electric Trailer Brake Assemblies for 3500 lb AxleThe hub/drums and the brake assemblies are sold separately, but the hub/drums do typically include the inner and outer bearings, the races, the grease seal, the dust cap and the lug nuts. A 3500 lb axle will typically use the L68149 inner and L44649 outer wheel bearing along with the # 58846 seal which has a 1.719 inner and 2.565 outer diameter. If this is the case, and your existing hub has a 5 on 4-1/2 inch bolt pattern, I'd recommend the etrailer # AKHD-545-35-EZ-K 10" hub/drum for...
view full answer... - Parts Needed to Add Electric Brakes to TrailerWe can absolutely help you find the parts you need for this! If your current trailer only has a 4 way, you will need to start by adding a 7 way plug; I recommend using one with a junction box like the Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector # HS381-9000 to keep the wiring clean and organized. You will need to remove the existing hubs in order to install the Dexter # 23-468-469. Once you've done this, you'll want to run the wires that went into the 4 way...
view full answer... - Will 12" Dexstar Wheel Fit 3,500 Pound Hub and Drum AssemblyYour typical 3,500 lb hub and drum assembly like the # AKHD-545-35-EZ-K will only work with 13"-15" wheels. Since the # AM20149 are 12" wheels they will not fit, regardless of any offset. You will need a larger wheel to fit the hub and drum assembly. Although we do not have a wheel with the same offset that would work, you could use the Dexstar Steel Mini Mod Trailer Wheel - 13" x 4-1/2" Rim - 5 on 4-1/2 # AM20253. This has the same bolt pattern with an offset of 0. Most trailer wheels...
view full answer... - Compatibility of Jeep Cherokee Wheels on 6 x 12 Dual Axle Cargo TrailerThe wheels from your 1993 Jeep Cherokee with 5 on 4.5 inch bolt pattern according to my research can be used on some trailers with hubs that match as long as the off-set of the Cherokee wheel allows the clearances needed to not make contact with the trailer frame. Trailer wheels typically have a zero offset, so that allows for better clearances and tire wear. Many Jeep wheels especially Wrangler wheels with 5 on 5 inch bolt pattern are used on cargo and off-road trailer applications where...
view full answer... - Determining If Electric Trailer Brakes Can Be Added to 2021 Anvil 6 x 12 Cargo TrailerI would be happy to help. To add electric trailer brakes to the 2021 Anvil 6' x 12' Cargo Trailer you mentioned you will need to do is verify that behind the idler hub is a brake mounting flange as shown in the included picture. If one is there brakes can be added pretty easily, and if one is not there brakes can still be added, but it will be a bit more work. If no brake mounting flange is installed you will need to have one installed. I was able to find that the Anvil 6' x 12' includes...
view full answer...
- Brake Assemblies for Karavan Model 2990-60-10-LR-BT Landscape TrailerAlthough there isn't a database that will tell me what hubs/bearings/brakes were originally used on your Karavan 5 x 10 utility trailer, the Karavan website lists the trailer's GVWR (gross vehicle weight rating which is the maximum the trailer plus its contents can weigh) as 2990 lbs which means the trailer likely uses a 3500 lb axle with a hub that has a 5 on 4-1/2 inch bolt pattern. See linked article which shows how to determine bolt pattern. You can confirm that it's a 3500 lb axle...
view full answer... - Converting Hydraulic Surge Brakes to Electric BrakesYou should just need a few components in order to swap out your hydraulic trailer brakes to electric brakes. I recommend the Electric Trailer Brake Kit # AKEBRK-35-SA and Trailer Hub and Drum Assembly # AKHD-545-35-EZ-K. When switching over to electric brakes on your trailer you will need to add a Trailer Breakaway Kit # 20400.
view full answer... - Replacement for Mobile Home Axle on Hudson Flat Bed TrailerWe do have some off-the shelf axles that exactly match the hub face to hub face and spring center to spring center distances you mentioned. We offer 3 different capacities: For a 3500 lb axle, use # T3584F-EZ-8974. For a compatible idler hub (no brakes) use # 84545UC1-EZ for a hub/brake drum, use # AKHD-545-35-EZ-K. the idler hub and the hub/drum have a 5 on 4-1/2 inch wheel bolt pattern, which is common for a 3500 lb axle. For compatible brake assemblies, use # AKEBRK-35R-SA for the right...
view full answer... - Parts Needed To Add Electric Trailer Brakes To Aluma 6810h Trailer With 3500lb Torsion AxleWhile we do not have a kit of all of the parts needed to add electric trailer brakes to your Aluma 6810h trailer, I would be happy to recommend all of the parts you need to complete the conversion. The first step is to see if your axle has brake flanges or not. If you do not have them a qualified axle shop can weld on a 4 bolt flange like the # 4-35 as they will have to be perfectly square, and the torsion axle having rubber inside of it will require carefully welding to avoid introducing...
view full answer... - What Hydraulic Brakes, Hub/Drums, and Spindles are Needed for a 3,500 Lb AxleIn order to add or replace a spindle on a trailer axle I would need to know the shape of the axle (round/square) in addition to the diameter (1-1/2",1-3/4", 2" etc.) If you have a round 1-3/4" diameter axle then I recommend using the EZ Lube Spindle part # TRU74FR. You would then need to match the braking assembly to both the brake mounting flange on the spindle and the capacity of the axle. For a 3,500 lb axle with a spindle that has a 4 bolt brake mounting flange, I recommend the Hydraulic...
view full answer... - What Type of Grease to Use for Dexter Axle Hub AssemblyTo add grease to the Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles # 84546UC3-EZ I recommend using the LubriMatic Prime Guard High Temperature Wheel Bearing Grease # L11380. This is the same type of grease used in our pre-greased equivalent of the Dexter Hub and Drum found as part # AKHD-545-35-EZ-K.
view full answer... - Availability of Complete Brake Kit with All Required ComponentsWe do offer electric brakes with brake assemblies, drums, bearings, races, etc as part of a complete axle kit. Examples can be seen on the link provided. For instance, part # e43SR is a complete kit with 3500-lb axle beam, electric brake assemblies, hubs/drums, bearings, races, seals, and mounting hardware. Individual items are also available as you noted.
view full answer... - Locating Replacement Hubs for European TrailerFrom what I could find there shouldn't be any difference between a European wheel bolt pattern and a US pattern. With that being said, you can verify this by measuring your existing bolt pattern to make sure it matches up to what we have available. I have attached a great article that explains exactly how to do this. In order to pick out the correct replacement hubs for your trailer, I recommend pulling an assembly and checking for the bearing numbers that are used. These numbers should...
view full answer...
- Best Way to Determine Weight of a Boat TrailerThe easiest and most reliable way to determine the weight of your trailer would be to take it to a weigh station and have it put on one of the scales. On the plate of the trailer near the coupler that lists the GVWR this info may be listed there as well.
view full answer... - Why Is Capacity of Hub 8-247 Lower Than GVWR of 2006 Trailmanor 2720SLThe reason a hub - as well as an axle - is sometimes rated lower than the GVWR of a trailer is because some of the trailer's loaded weight is going to be tongue weight, which is weight that is going to be applied to the tow vehicle as opposed to the trailer. If your 2006 Trailmanor 2720SL has a hub that is part 8-247, the correct replacement hubs are going to depend on if you have a standard axle or E-Z Lube Axle: - Standard Axle: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles...
view full answer... - Recommended Replacement Brake Assemblies for Enclosed Cargo Trailer with 3500 lb AxlesA hub drum for 3500 lb axle would use a 10 x 2-1/4 inch brake assembly. I'd recommend using self-adjusting brake assemblies, such as part # AKEBRK-35-SA, which would include both a left and right brake assembly. If your 7 x 14 enclosed cargo trailer is a tandem axle, you'll need two sets. The mounting hardware is sold separately as part # BRKH10B, again for a tandem axle trailer, you'd need two sets. I'd also recommend inspecting the armature surface of your brake drums, where the brake...
view full answer... - Is the Timbren Axle-Less Suspension System 2000 lbs Compatible with Electric BrakesYou can use electric brakes with a Timbren Axle-Less Suspension System rated for 2,000 lbs, however, you would need the Heavy-Duty system, part # ASR2KHDS01. The Timbren Axle-Less suspension system, # A20RS545, that you referenced is not compatible with trailer brakes because it does not have a brake mounting flange at the base of the spindle. The Timbren Heavy-Duty system, comes with a brake mounting flange with a 4 on 4 bolt pattern which fits most 10 inch brake assemblies. The brake...
view full answer... - How To Add Electric Trailer Brakes to a Trailer with 3.5K AxleIn order to add electric trailer brakes to a trailer with 3,500 Lb Axle all you need is braking assemblies (Electric Trailer Brake Kit part # AKEBRK-35-SA), hubs/drums (Trailer Hub and Drum Assembly part # AKHD-545-35-EZ-K), and a wiring kit (Trailer Wiring 7-Way Upgrade Kit part # HS381-9000). Please note, the hubs and drums are sold individually so you'll need two per axle.
view full answer...
- Replacement Hub an Drum Assembly for 2021 K-Z Sportsmen Classic 181BHFor a hub and drum assembly that fits your 3,500 lb axle on your 2021 K-Z Sportsmen Classic 181BH you need the Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 # 84546UC3. If you have E-Z lube axles then you need the # AKHD-545-35-EZ-K instead. Both of these use a # L68149 inner and # L44649 outer bearing. They have a 5 on 4-1/2 bolt pattern and use 10" brake assemblies like the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand...
view full answer... - How To Find Correct Replacement Bearings and Hub for Outback Trailer with AL-KO AxlesI have a few options for you to help with identifying the bearings on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to find the bearings based off industry standards. For example, a 3,500 lb axle uses L68149 and L44649 bearings like what comes with the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles part # BK2-100 or the Easy Grease Trailer Hub and Drum Assembly...
view full answer...
Do you have a question about this Trailer Hubs and Drum?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Edited by:
Lindsey S
Installed by:
Jeff D
Installed by:
Randy B
Video Edited:
Joshua S
Video Edited:
Jacob T
Video by:
Chris R
Video by:
Zach D
Video by:
Jonathan Y
Updated by:
Wilson B
Updated by:
Mike S
Written by:
Alexander C
Test Fit:
Shane H
Test Fit:
Kevin C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Brooke M.
9/17/2022
Thank you for reaching out. I have sent this to our customer service team and they will be in touch about the missing pieces.