Determining If Electric Trailer Brakes Can Be Added to 2021 Anvil 6 x 12 Cargo Trailer
Question:
I am considering buying a used Anvil 6x12 single axle, but only if I can install brakes. Are your brakes compatible? I dont have any other info except that it is a 2021 model.
asked by: Joe N
Helpful Expert Reply:
I would be happy to help.
To add electric trailer brakes to the 2021 Anvil 6' x 12' Cargo Trailer you mentioned you will need to do is verify that behind the idler hub is a brake mounting flange as shown in the included picture.
If one is there brakes can be added pretty easily, and if one is not there brakes can still be added, but it will be a bit more work.
If no brake mounting flange is installed you will need to have one installed. I was able to find that the Anvil 6' x 12' includes a 2990lb axle which likely has a 2-3/8" diameter. If that is the case then the # 4-35 would be the correct flange. This will need to be installed by an axle shop as it needs to be perfectly square to the axle to prevent premature brake wear and decreased braking performance.
Next since the axle has a 2990lb rating it would use 3500lb braking assemblies # 23-468-469.
When it comes to hub and drum assemblies you will likely need the # AKHD-545-35-EZ-K, but you will want to confirm the bearing combination first by removing one of your current hubs and looking for the bearing number stamped in the face of both the inner and outer bearings as shown in the included picture of the # L44649. This hub uses inner bearing # L68149 and outer bearing # L44649 so as long as that is what your current hub uses this would be correct. If you have a different bearing combination just let me know.
Moving on to the wiring there are a few different things you will need to add. First being a 7-way connector # H20046 and junction box # 38656. You will need to run # 10-1-1 from the junction box to the brake magnet on each of the braking assemblies as well. Second you will need to add a breakaway kit using the # C52042 which is a fail safe that automatically applies the brakes on your trailer should it become disconnected from your tow vehicle.
That completes everything on the trailer side of things, but you will need to make sure your tow vehicle has a fully functional 7-way connector and a trailer brake controller. If you are missing either of these components just let me know the Year/Make/Model and I would be happy to make a recommendation for you.
I included videos of the products mentioned and a link to a helpful article on adding electric trailer brakes for you to take a look at.
Products Referenced in This Question
Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Brake Mounting Flange for 2-3/8" Round Axle
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 10 Inch
- 2-3/8 Inch Diameter Axle
- Redline
more information >
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Curt Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Side Load
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-axle
- Tandem-axle
- Triple-axle
- LED Tester
- Battery Included
- CURT
more information >
Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 6 - 10 Feet Long
- Plug and Lead
- 7 Round - Blade
- Hopkins
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 12 x 2 Inch Drum
- 5200 lbs Axle
- 6000 lbs Axle
- 7000 lbs Axle
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Article: Most Popular Wheel Bearings
- Q&A: Replacement Brakes for a 5th Wheel Trailer with 5.2K Lippert Axles
- Article: Trailer Wiring Diagrams
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Q&A: Replacement Trailer Brake Assembly for B12EA-22 on 2018 Forest River 294BH Travel Trailer
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Trailer Tire Sizing
- Q&A: What is the Best Grease for Trailer Bearings
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Overview of Lubricating Grease
- Q&A: Should There Be Any Play After Installing An Easy Grease Trailer Hub and Drum Assembly
- Q&A: Comparing the eTrailer and Dexter Electric Trailer Brake Kits
- Q&A: Are New Brake Drums Required if Replacing Electric Brake Assemblies on a Trailer
- Q&A: How to Select Hub/Drums & Electric Brakes For Trailer