Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…
Thanks for letting us help Stephen. The TecNiq ID Light Bar #TN25TR has mounting holes spaced 8-1/2" apart on center, so unfortunately, it won't work for the mounting dimensions you provided. I looked through the ID light bars we carry and…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…
Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The #AL91RB and #AL91AB will work with the Mounting Bracket #A91BB and then for a pigtail you can use the Right Angle…
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…
Thanks for letting us help Stephen. The TecNiq ID Light Bar #TN25TR has mounting holes spaced 8-1/2" apart on center, so unfortunately, it won't work for the mounting dimensions you provided. I looked through the ID light bars we carry and…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…
Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The #AL91RB and #AL91AB will work with the Mounting Bracket #A91BB and then for a pigtail you can use the Right Angle…
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
Bright led light with submersible lights means reliable visibility even when the trailer gets dunked at the ramp. Waterproof housings and straightforward installs make them a solid pick for boat trailers, with options for 3-prong triangular plugs or simple hardwiring. For the best fit, match your old light's size or grommet opening before you swap.
Installation is generally straightforward. If your trailer is bolted together, running dedicated grounds to each light can help. Avoid nyloc nuts where a carriage bolt sits in a plastic track to prevent spinning. Seal splices and fill pigtail sockets with dielectric grease. Some choose to disconnect lights before launching so they aren't energized underwater.
LED submersible lights are noted as nice and bright with a crisp color; some include a reverse light for added visibility. If vertical mounting is blocked, certain lights work well horizontally—confirm the lens and housing support your chosen orientation. High-mounted LEDs can improve rear visibility when cargo or bikes block lower lights.
Choose LED submersible lights that use the same triangular 3-pole connector. Confirm the connector shape and pin count, and that the stop/turn/tail functions match your harness; the driver's side often includes a license plate light. If the plugs differ, splicing with heat-shrink solder can make a solid connection. Add dielectric grease to help keep water out.
They can, but confirm dimensions against your trailer's cutout and grommet. If an exact-contour light is discontinued, pick a similar-size LED submersible unit and check length, height, and depth carefully. Wraparound lenses and unique contours may not swap, so upgrading to a full LED assembly is sometimes the better route.
Clearance Lights
License Plate Lights
Tail Lights
Utility Lights
Filters
