Filter by Style of Light

$2.40 - $56.01

$4.54 - $177.78

$4.17 - $47.42

$1.18 - $187.88

$5.16 - $145.65

$5.76 - $692.77
Videos
for trailer lights
Help Articles
for trailer lights
Expert Answers
for trailer lights
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...Hey Glen. We've got a couple of options for Optronics Smoke Series lights but we don't have the STL87DSRSHB which is a part number for a 10 pack. It looks like Optronics is phasing out the STL87 smoke series as well so I can't get them.…
view full answer...A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
view full answer...The Wesbar 271594 is a sealed light which means the lens is not replaceable. The only solution is to replace the entire light. The parent company for Wesbar recently changed, so as of May 2023 this particular light is on indefinite backorder. I…
view full answer...That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
view full answer...Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…
view full answer...Hello Matsubayashi, I wanted to start by letting you know that we do not ship directly to Japan. If you have someone located in the United States, we would be happy to ship the order to them so they can forward it to you. I am showing that your 1995…
view full answer...It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
view full answer...Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.
view full answer...The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…
view full answer...Hey Harry, thanks for reaching out. Your Coachmen Freedom Express is set up for 30 amp service and we do have twist lock power inlets that will work for you. What you'll need is one of the following: - Mighty Cord Replacement RV Power Inlet -…
view full answer...Videos
for trailer lights
Help Articles
for trailer lights
Expert Answers
for trailer lights
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...Hey Glen. We've got a couple of options for Optronics Smoke Series lights but we don't have the STL87DSRSHB which is a part number for a 10 pack. It looks like Optronics is phasing out the STL87 smoke series as well so I can't get them.…
view full answer...A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
view full answer...The Wesbar 271594 is a sealed light which means the lens is not replaceable. The only solution is to replace the entire light. The parent company for Wesbar recently changed, so as of May 2023 this particular light is on indefinite backorder. I…
view full answer...That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
view full answer...Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…
view full answer...Hello Matsubayashi, I wanted to start by letting you know that we do not ship directly to Japan. If you have someone located in the United States, we would be happy to ship the order to them so they can forward it to you. I am showing that your 1995…
view full answer...It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
view full answer...Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.
view full answer...The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…
view full answer...Hey Harry, thanks for reaching out. Your Coachmen Freedom Express is set up for 30 amp service and we do have twist lock power inlets that will work for you. What you'll need is one of the following: - Mighty Cord Replacement RV Power Inlet -…
view full answer...Filters
- 1117 results
Filter Results
Clearance Lights
$2.40 - $56.01
Interior Lights
$4.54 - $177.78
License Plate Lights
$4.17 - $47.42
Reflectors
$1.18 - $187.88
Tail Lights
$5.16 - $145.65
Utility Lights
$5.76 - $692.77