Replacement Brake Assemblies, Hubs, and Bearing Kit for a Dexter 3,500 EZ Lube Axle

Question

Question:

Good Morning, I have two old Dexter Axles that I’m trying to service. The label says they are P-15 Model SLR. The serial numbers are D2665978 and D2665979. Can you tell me the original axle capacity, hub/drum assembly, bearings, seals, and brake assembly for this model so I know what parts to order? Thanks!

asked by: Blake S

0

Expert Reply:

I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested:

Hub/Drums

- 5 on 4-1/2 Lug Nut Pattern item # AKHD-545-35-EZ-K

- 5 on 4-3/4 Lug Nut Pattern item # AKHD-5475-35-EZ-K

- 5 on 5 Lug Nut Pattern - item # AKHD-550-35-EZ-K

- 5 on 5-1/2 Lug Nut Pattern - item # AKHD-555-35-EZ-K

- 6 on 5-1/2 Lug Nut Pattern - item # AKHD-655-35-EZ-K

Brake Assemblies

- Manual Adjust - etrailer Electric Trailer Brakes item # AKEBRK-35

- Self Adjusting - etrailer Electric Trailer Brakes item # AKEBRK-35-SA

- Hydraulic - etrailer Hydraulic Trailer Brakes item # AKUBRK-35

Bearing Kit - Lippert Complete Bearing Kit for 3.5K Trailer Axles item # LC55ZP

What kind of trailer do you have, does it use hydraulic or electric brakes, and what lug nut pattern do your hubs have?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

Dexter Axle Tag
(click to enlarge)

Blake S.

8/10/2026

It’s a 1998 Sundowner ValueLite. It looks like Sundowner supplied the hubs and brake assembly and Dexter only provided the beam. They are electric brakes. The hub pattern is 6 on 5.5”

Jerred H.

8/11/2026

@BlakeS Ok, that makes so much more sense as to why the build sheet was so vague. Usually, they have hubs and brakes listed. You'll need the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item # AKHD-655-35-EZ-K. This hub is sold individually and comes pregreased with the bearings and seals installed. It has a 6 on 5-1/2" lug nut pattern. I recommend replacing your brakes with the Self Adjusting - etrailer Electric Trailer Brakes item # AKEBRK-35-SA. You'll never have to adjust them or tune them in. The minimal upfront cost increase is definitely going to save you time down the road.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 9

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Brake Assemblies, Hubs, and Bearing Kit for a Dexter 3,500 EZ Lube Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching