Marker Light Dimensions Without Grommet PET45FJ

Question

Question:

What are the dimensions of the light without the grommet?

asked by: Pat B

0

Expert Reply:

Great question, Pat! The light itself part # PET45FJ, without the grommet, measures 2-1/2 inches long by 1-3/16 inches wide. I’ve added a diagram for reference showing where those measurements are taken on the red light.

What does your current light measure?

expert reply by: Heather A

0

light
(click to enlarge)

Answer 1

Hey Robert, welcome back! The Black Bracket and Single Wire Plug item #A65PB or the Chrome Bracket and Single Wire Plug item #A67CB are both mounting brackets for the GloLight Thinline LED Trailer Clearance or Side Marker Light item #MCL165AB. What…

view full answer...

Answer 2

Hi Vero, great question! The amber version of the Peterson PC Rated LED Clearance and Side Marker Light part #PET45FJ is part #PET95FJ. It has the same 2 -1/2 inch long by 13/16 inch wide by 1-1/4 inch tall dimensions as the red version, and it comes…

view full answer...

Answer 3

Hi Joshua, thanks for your question! The Peterson PC Rated LED Clearance and Side Marker Light, part #PET45FJ, comes with the grommet and plug, so you have what you need to install the light. The plug that comes with it is the Peterson #142-49 which…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Marker Light Dimensions Without Grommet PET45FJ

Product Page this Question was Asked From

Continue Researching