Product Experts Available Now!
Call 800-298-8924
Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
(282 reviews)
Price: $8.04
In Stock
Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
Item # MCL95AB
Retail:$11.97
Our Price: $8.04
You Save: 33%
Orders above $99 qualify for Free Shipping
In Stock
- All Info
- Reviews (282)
- Q & A (35)
- Videos (3)
- Photos
- Why etrailer?
Optronics Trailer Lights - MCL95AB
- Clearance Lights
- Rectangle
- LED Light
- Amber
- Surface Mount
- 2L x 1W Inch
- Optronics
- Submersible Lights
- Rear Clearance
- Side Marker
2-1/8" x 1-1/8" Rectangle. Waterproof, LED trailer light serves as either a side marker light or clearance light when properly mounted. Durable polycarbonate lens and housing. Stud mount to trailer. Single wire design. P2 rated.
Features:
- LED trailer light functions as a clearance light or side marker light when properly mounted
- Sonically sealed, waterproof housing and lens unit is submersible
- LEDs make great replacements for incandescent lights
- Last 50 times longer
- More efficient - provide brighter light with less power output
- No bulbs to replace - no brittle filaments
- Durable polycarbonate housing and lens
- Amber lens over white LEDs
- Compatible with 12V DC systems
- Stud mounts to trailer with included stud and stainless steel base
- 1-Wire design grounds through mounting hardware
- P2 rated
Specs:
- Dimensions: 2-1/8" long x 1-1/8" wide x 1-1/16" deep
- Lead wire: 20" long
- Diodes: 3
- Power draw at 12.8V: 0.051 amps
- Lifetime LED warranty
Manufacturer Cross Reference
Light will work as an exact replacement for:
Bargman # 42-99-402
Sonically Sealed, Waterproof Trailer Light
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
P2-Rated Lights
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
MCL95AB Optronics LED Clearance or Side Marker Trailer Light - Submersible - 3 Diodes - Rectangle - Amber Lens - P2/P3 Rated
Alternate part number: MCL-95AB
California residents: click here
Video of Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Optronics Sealed Mini Rectangular LED Stud Mount Trailer Clearance Light Installation
Today on our utility trailer we'll be installing the Optronics Sealed Mini Rectangular LED trailer clearance light. Part number MCL95AB. Now these Optronics trailer clearance side marker lights are sold individually. Now we will be installing two of them on our trailer today. Here's what our light looks like. It's got a single stud on the back, so we'll go ahead and take the nut and the lock washer off.
Now depending on your particular trailer you may need to drill an extra hole to allow for the electrical lead to fish through. We'll go ahead and feed the wire in and we'll go ahead and make sure that the wire comes up through this portion right there, so it doesn't pinch the wire. With our light in place the stud coming through the metal bracket go ahead and take our lock washer, put it back over the stud, then we'll put our hex nut back in place. Now this is the hardware the comes with it: a lock washer and a nut, but you'll see how large of a hole is already in this trailer. We're just going to add another flat washer here to take up some of the gap, so it'll be more like that and then we'll put the lock washer followed by the hex nut. Go ahead and take our socket wrench and tighten down the nut.
Then this lead here will run over and tie in with our running light circuit, which will be the brown wire on our trailer wiring. Now the ground is actually grounded through this stud right here, so that's where the ground portion is so we only need to run a single wire over to our junction box. It's already installed on this trailer. Now we're going to have to add a section of wire to run over to our junction box or we'll tie in with the running light circuit. To do this we'll be using a heat shrink butt connector, which is part number DW05743-5. Go ahead and strip a little bit of wire back.
Just get a good clean spot. We're just using 14 gauge wire to extend over. Go ahead and slide that on and then we'll crimp it. Go ahead and crimp this side as well. Now ideally to shrink this, if you had a heat gun, we would use a heat gun to make it be a nice uniform seal, but most people don't have a heat gun at home so we're just going to use a lighter and go back and forth and make the heat shrink portion of the connector seal around the wires. Now when we route our wire over towards our junction box on this trailer.
We're going to be using some quarter inch wire loom, which is part number 7509-10. As well as some loom clamps. Part number A0250. Now to attach the loom clamps to the trailer, we'll be using some self tapping screws. Part number 101131802. Go ahead and take our quarter inch wire loom. We'll slide it in over the top of our wire. Now that we have our loom installed we'll go ahead and feed our wire over towards our junction box. Now we're going to go ahead and put a hole in here for our quarter inch loom clamp. Go ahead and put our loom clamp around our quarter inch wire loom. Then we'll put our self tapping screw through the clamp and we'll go ahead and tighten it down with our socket wrench. We're going to go ahead and put a couple more loom clamps and self tappers to support and secure our wire as we run it across to the other side of the trailer. Now that we've got our wire pulled over to other side of the trailer. We're going to go ahead and install our other light. Go ahead and feed our wire through our little hole here. Make sure that we don't pinch the wire on the back side. Go ahead and trim down our quarter inch wire loom and go ahead and take this end of the wire. Feed it in. Now we're going to go ahead and make our connections up here. Again we'll be using a heat shrink style butt connector. Part number DW05744-5. Now since we need to add a wire that runs up to our junction box we're going to go ahead and add this wire in right here, so we'll be connecting two wires together on one side of the butt connector. So we've got our wires in place, we'll go ahead and crimp it down. Now on this side we'll actually be using a heat gun to show you the difference between the heat gun and a lighter. Now we'll go ahead and put our wire back into the wire loom and go ahead and take another piece of wire loom and feed it onto this wire that goes up to our junction box and then we're going to go ahead and use some electrical tape to secure up our connections here. Go ahead and add one more loom clamp in right in this area right here. Helps secure the wire. Now that we've got our wire pulled down here underneath the trailer there's already a junction box that's been mounted. The junction box that we'll be tying in with is part number 38656. We'll just need to route our wire in through one of these grommets here. Right here is the tail light circuit, so we'll be tying in right here. We'll need to trim our wire to length. We'll then be installing a ring terminal, which is part number DW05702-1. So we'll go ahead and take our ring terminal and our crimpers, crimp it down on the wire. Then take our socket wrench, take the nut off of the stud here. Now there is a nut and a little star washer underneath to keep the nut from backing off, so we'll need to remove both of those. Go ahead and slight that on and put the star washer and the nut back on and then we'll tighten it down with our socket wrench. Now before we put our cover back in place on the junction box. We'll go ahead and take our tester and make sure that the two new side marker clearance lights are working just fine. Now if you don't have a tester you can simply plug it in to your tow vehicle and check it that way as well. Now that we know everything works just fine we'll go ahead and put the cover back in place. That'll do it for our installation of the Optronics Sealed Mini Rectangular LED trailer clearance and side marker lights. Part number MCL95AB. .
Customer Reviews
Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens - MCL95AB
Average Customer Rating: 4.9 out of 5 stars (282 Customer Reviews)
2-1/8" x 1-1/8" Rectangle. Waterproof, LED trailer light serves as either a side marker light or clearance light when properly mounted. Durable polycarbonate lens and housing. Stud mount to trailer. Single wire design. P2 rated.
- MCL95AB
by: Johnna05/09/2019
Good light came in quick 639945
- MCL95AB
by: Tom05/29/2019
My order went very well. Website and ordering made simple. Impressed. 647867
- MCL95AB
Chuck M - 02/04/2015
9264
by: Chuck M.08/06/2013
Fit perfectly. Soldered the wires together and covered with heat-shrink tubing. Nice and bright. Survived one dunking so far. 93550
Comments
Still working perfectly! I try to always be sure to disconnect the wire harness before dunking, just to be safe.
Chuck M - 02/04/20159264
- MCL95AB
Rob R - 10/21/2016
21586
by: Rob R.10/22/2015
Exact quality replacement of the lights that come on the trailer. LEDs make them a really nice upgrade on older trailers with single post installation. 230516
Comments
Lights holding up well! I make sure to rinse them well after salt water use.
Rob R - 10/21/201621586
- MCL95AB
by: Jeffrey04/30/2018
Once again, the best in service and selection. Ordered the marker lights and they appeared in my mailbox almost as quickly as it took to log off the site. Products are as described, priced amazingly well and perform as advertised. This is the supplier to use for high quality items that far surpass those available in "parts stores" or Big Box retailers. Have used their products on two boat trailers and one equipment trailer, every item far better than OEM and true to descriptions... 502526
- MCL95AB
by: Marvin S04/18/2018
I want to thank you for all your help with my trailer you were more helpful than you realize. So this is my trailer for a 22' Flats Cat shallow draft Catamaran. I totally dismantled my trailer and buffed by hand with a wire buffer and sand blasted in some spots and applied multiple coats of some very expensive galvanize paint (Z.R.C.). I installed all new C. E. Smith Carpet (about 80'), seven new LED waterproof lights, new springs, new equalizers, new tongue jack, new wench, new safety chain, new chain brackets, all new SS hardware and a 35' long wiring harness. I was able to send only one review with a picture of the safety chain and brackets. I'm having a little trouble with the rest..oh some of these items were bought locally or from your competitors, until I found ETRAILER. Your prices were cheaper for the exact same things. Your helpful how to videos were helpful. And Rose, your personal helpful knowledge made my buying experience very pleasant, I actually enjoyed talking to you! Thanks to ETRAILER and specifically to Rose G. 497942
- MCL95AB
Jeremy P - 06/09/2015
12432
by: Jeremy P06/08/2014
Marker light is clear and bright. The light grounds itself through the mounting stud by design, but I used a ring terminal and wire lead to connect to the ground on the wiring for a bit better grounding source. Works perfectly and saves me time at the boat ramp by not having to disconnect the trailer lights since they are all LED's. 134732
Comments
Everything still working like new after a dozen trips to the lake. Definitely recommend.
Jeremy P - 06/09/201512432
- MCL95AB
Eric - 02/26/2019
49896
by: Eric02/26/2018
Very bright, very easy install; only reason for 4 stars is bc I just installed them and can't speak for their longevity; I drilled a small hole in my trailer next to the main mounting hole to poke the wire through, so as not to see the wire; looked very nice. 479238
Comments
As of the last time I launched which was in November the lights still worked great. They have been fully submersed many times in either fresh or salt water.
Eric - 02/26/201949896
- MCL95AB
by: Barry02/12/2019
Outstanding product. Used these to go "retro" and put on my Ram running Boards. Easy install. Just made some holes in pinch weld - ran to 4 pin trailer connection and BAM - all good. Lights delivered quickly and in great shape. Recommend this product. 604497
- MCL95AB
by: Charles03/28/2020
These lights are exactly what I was looking for. They arrived in short order and in excellent shape. Very good product and customer service! My Magic Tilt trailer will now appear to be new again! Thank You 771844
- MCL95AB
by: Bryan03/16/2020
Everyone was very helpful great prices product got there very quick 766653
- MCL95AB
by: James03/06/2020
Replacing side light lost to blow-out, this light will more than replace the single LED light I had on the fender before. Dimensions and photos made it easy to buy. 763602
- MCL95AB
by: Jackie03/02/2020
Good quality light! Used as marker lights on 24' boat trailer. 762456
- MCL95AB
by: John03/01/2020
Not cheap, but what I needed and worked. 762325
- MCL95AB
by: Clifford02/22/2020
Good product and prices ,,, These lights are better lookin than the pictures show,,, 757332
- MCL95AB
by: Rusty01/30/2020
These lights work well and a good value. 745887
- MCL95AB
by: Jeff M.12/13/2019
Great product 732112
- MCL95AB
by: Franklin12/11/2019
Very nice lights fastest shipping I’ve seen my new store 730792
- MCL95AB
by: Jpw11/26/2019
Worked well as expected. 727899
- MCL95AB
by: Mark11/20/2019
shipped on time as promised, can not wait to install!! 726780
- MCL95AB
by: Dan B11/03/2019
LED lights are so much brighter. 722308
- MCL95AB
by: Donald10/15/2019
They are oem for magic tilt trailer! Great sevice and quick shipping. I will buy more if I can find them in red. 717637
- MCL95AB
by: Trailer repair10/09/2019
Repeat customer. Have always been satisfied with price and products are as described. 716340
- MCL95AB
by: J Boo10/02/2019
Good money saver. Pretty simple project. I will do it again when needed. 715405
- MCL95AB
by: Timothy09/21/2019
Wonderful product for an even better pr ice. 706415
26
283
Show More Reviews
Ask the Experts about this Optronics Trailer Lights
- Replacement Trailer Lights for Shoreland'r Boat TrailerFor other options we have # MCL95AB for amber lights and # MCL95RB for red. They're still surface mounted lights but the base is included and may work for you. They're also a single wire design so they ground through the mounting hardware. If these will not work for you reply to my email with your pictures and dimensions and I'll see if I can find some that will.
view full answer... - Can 12 Guage Wire Connect to 20 Gauge Wire With Butt ConnectorsWhen you have to go from a much thinner gauge wire to a thicker gauge wire with a butt connector you want to use the bigger size connector like # DW05745-10 which fits 10 to 12 gauge but the trick to getting the thinner gauge wire to fit well is to strip off 3 times as much insulation than you'd normally need and fold the core of the wire a couple times so that it ends up being thick enough for the butt connector to grab it.
view full answer... - How to Mount Trailer Clearance Lights that Ground Through the Mounting StudsWith a one wire light like the Optronics Mini Rectangular LED Clearance Light, item # MCL95AB, you can ground the light in one of two ways. If the light is mounted to a location that allows for the mounting bolt or screw to contact a good ground location such as the vehicle frame then you can mount the light in this location. Then, run the power wire to a 12 volt positive tail light circuit without further wiring. If the location the light is mounted to is not a good source of ground,...
view full answer... - LED Amber Colored Trailer Clearance Light with 2 Wire DesignThe Optronics LED Clearance Light # MCL95AB does ground through the mounting stud. For a different yet similar light you can use # MCL13A2B with snap-on ring # A13B2B that is a 2 wire light and does have a ground wire.
view full answer... - Troubleshooting LED Lights on 2008 Shadow Horse TrailerSince most of your trailer lights are functioning I would check the two subject lights' mounting and wiring for the cause for the problem. If the light uses a mounting stud or mounting hardware to establish the ground, like # MCL95AB, then you can try sanding/cleaning the mating surfaces to remove any corrosion, dirt or trapped moisture that could be interfering with the electrical connection. Also inspect the wiring for signs of damage from road debris or hungry critters. Once you have...
view full answer... - Replacement for Optronics MCL-95APG Trailer Clearance Light The Optronics Sealed Mini Rectangular LED Trailer Clearance Side Marker Light # MCL95AB referenced in your question is the closest option we have available to the MCL-95APG model you mentioned. The only difference appears to be the type of wiring that is included with the light, as the model you have features a quick-plug style connector while the # MCL95AB has a single power wire with a bare end. It will ground through its mounting stud. The MCL-95APG light assembly is no longer available...
view full answer... - Are Mounting Brackets Available for Optronics Mini LED Clearance Lights # MCL95AB and # MCL95RBThe Optronics Mini Rectangular LED Clearance Lights, # MCL95AB and # MCL95RB, are single stud surface mount lights, so they do not have a grommet or mounting bracket available. They were designed to mount directly to an existing bracket or to the trailer frame. The closest clearance lights that we carry to the dimensions of your current lights are the Optronics Square LED Clearance Light, # MCL36AB and # MCL36RB. These are also single stud surface mount lights, but the larger size should...
view full answer... - Recommended Stud-Mount Single-Wire Mini Rectangular LED Clearance Light For Boat TrailerWe do have a clearance light that will work for you. I recommend the Optronics Mini Rectangular LED Trailer Clearance Light, part # MCL95AB. This is a 3-diode light that measures 2-1/8 inch x 1-1/8 inch and is 1-1/16 inch deep. It is a stud-mount single wire light with an amber lens. This light has a sealed, waterproof housing, so it will work great for your boat trailer.
view full answer... - How Long is the Power Wire Attached to the # MCL95AB LED Clearance LightThe length of the Wire attached to the Optronics Trailer Clearance Lights, item # MCL95AB, is 19-1/2 inches long.
view full answer... - Availability of a Clear LED Trailer Clearance Side Market LightThe closest match we have to the mini rectangular LED trailer clearance trailer side marker light # MCL95AB is the Optronics sealed, LED mini utility light # UCL13C2PG. It's 2-1/2 inches long and 1-1/16 inches wide. Other potential options to consider: # MCL13CA2B # MCL63CAB # MCL65CAB # AL91CAB I included an informative article and several video reviews too.
view full answer... - Dimensions Of Mounting Stud On Optronics LED Trailer Clearance, Side Marker LightThe mounting stud diameter on the LED Trailer Clearance, Side Marker Light, part # MCL95AB measures 5/8 inches long and is 1/4 inch diameter. This comes with the nut and washer needed to install on your trailer. This is a single-wire design light. The mounting stud also doubles as the electrical ground. I have attached a link to a video you can check out.
view full answer... - Recommended Amber Side Marker Light for Snowmobile TrailerI highly recommend the Optronics Sealed, Mini Rectangular LED Trailer Clearance, Side Marker Light # MCL95AB. This is an LED light which is 2-1/8" long x 1-1/8" wide x 1-1/16" deep and mounts by plated steel stud on base of light. It has gotten close to 200 reviews from our customers who have used it and a nearly 5-star review. I've added a link to a review video of the light for you to take a look at.
view full answer... - Recommendations for Submersible Boat Trailer Lights that Short Out when SubmergedThere may be some wiring on your trailer that is exposed that is causing the short on the circuit, if you can locate that and repair it as necessary you should be able to eliminate the shorting and fuse blowing you are experiencing on your trailer. I attached a demonstration video for the Optronics Trailer Light # MCL95AB for you to check out also. The other option you have would be to unplug your trailer connector before you submerge it in water. I attached an FAQ article on trailer...
view full answer... - Can the Optronics Clearance Light # MCL95AB be Mounted and Grounded to an Aluminum Trailer FrameYou can still use the Optronics clearance light # MCL95AB with an aluminum frame. This light grounds through the mounting stud. In the event that you end up with a bad ground to the frame, you can attach a wire behind the mounting stud and run it to the main ground on the trailer connector.
view full answer... - How Long is the Mounting Bolt on the Optronics LED Clearance Light # MCL95ABThe bolt on the back of the clearance light # MCL95AB is approximately 5/8 inches long from the back of the light housing to the end of the bolt. Not all bolts on lights equipped with them are the same length but they are generally within very close proximity, no more than 1/4 inch off, from the lights I have measured. The stud in this light is also the grounding point. Similar lights, like # MCL13A2B, would mount using 2 screws with gasket # A13G2B. This light has 2 wires so you would...
view full answer... - Connection Recommendation for Connecting 12 Gauge and 20 Gauge WireI wouldn't recommend using quick splice connectors when trying to connect to different gauge wires (as well as in general). Ideally you solder the connection or you use butt connectors. If you use butt connectors you'll want to use the yellow ones like part # DW05745-10 which are for 10 to 12 gauge wires. On the lighter gauge wire you'd need to strip back quite a bit more wire than needed and then fold the wire core a few times to thicken it up and allow the butt connectors to grab them.
view full answer... - Is Optronics Mini Rectangular LED Trailer Clearance/Side Marker Light MCL95AB SubmersibleThe Optronics Mini Rectangular LED Trailer Clearance/Side Marker Light # MCL95AB is indeed submersible. This single-wire light uses the mounting stud to establish the ground connection and the one pigtail lead accepts the +12V signal. Please refer to the linked video.
view full answer... - Can 3 Sealed, Mini Rectangular LED Trailer Clearance, Side Marker Lights, # MCL95AB, Wire TogetherYou can wire 3 of the Sealed, Mini Rectangular LED Trailer Clearance, Side Marker Lights, # MCL95AB, to a single power source by splicing all three power wires together then going to a common power source. This would mean only having to make one splice rather than multiple splices like you have described and the lights would work much better. You might just need a little extra wire # 12-1-1 to reach. This wire is sold in 1 foot increments. I have included a link to a video review of...
view full answer... - Solution for Needing Side Reflectors on Vehicle FenderThat's a pretty odd place for someone to install a turn signal on a vehicle, but for a replacement that's similar we have the Sealed, Mini Rectangular LED Trailer Clearance, Side Marker Light # MCL95AB which has dimensions of 2-1/8" L x 1-1/8" W x 1-1/16" D.
view full answer...![]()
- PC Rated Clearance Light Similar to the Sealed, Mini Rectangular LED Trailer Clearance # MCL95ABPC rated means that the light is viewable from a 90 degree angle. Most other lights are considered to be viewable from a 45 degree angle. The Sealed, Mini Rectangular LED Trailer Clearance # MCL95AB is not a PC rated clearance light. The closest light we offer to that light that is PC rated is the Mini Thin Line Sealed LED Marker/Clearance Light # AL82AB. I also attached a link to a page that has all of the PC rated clearance lights we offer.
view full answer... - Clear Lens Version of the Sealed, Mini Rectangular Trailer Utility Light # UL94CBYes, we do carry a version of the # MCL95AB with a clear lens. For that you would want the part # UL94CB.
view full answer... - Troubleshooting Trailer Clearance Lights that Don't Fully IlluminateSounds like you are overloading the running light trailer wiring circuit of your truck and that is why the lights aren't wanting to illuminate properly. Easiest solution for that is to replace all the lights with LEDs as they draw considerably less. I attached a link to all of the trailer clearance LED lights we have. Are there quite a few clearance lights on your trailer?
view full answer... - Amber Clearance Light Recommendation to Increase Night Time Visibility You'd want to go with amber, LED clearance lights like the part # MCL95AB as LEDs are much brighter than incandescent bulbs. For more of a strip style light you'd want the part # MCL19AB.
view full answer... - Upgrading Lights on 2000 Tracker PT175 Trailer to LEDWe do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I can be sure to recommend the correct parts.
view full answer...![]()
![]()
![]()
![]()
- Rewiring Boat Trailer for 7-Way to Use LED LightsThere are a number of things you will need if you want to re-wire your boat trailer to use LED lights and you should start with the Epicord 7-Way Molded Trailer Plug with Junction Box # 277-000141. Keep in mind you will also need Ring Terminals # 44-5310A and Loom Clamps # A0500 The box is color coded like this: - White (ground): 10 gauge - Black (12V power): 10 gauge - Yellow (reverse/auxiliary): 14 gauge - Red (left turn and stop): 14 gauge - Green (tail and running lights):...
view full answer...![]()
- Replacement Optronics LED Trailer Marker Lights with Single Mounting Stud It sounds like you are looking for the Optronics Sealed, Mini Rectangular LED Trailer Clearance Light # MCL95RB in Red and # MCL95AB for Amber. These sealed, waterproof LED light assemblies measure 2-1/8 inches long and 1-1/8 inches wide. They feature a single mounting stud on the back. These do have a single wire design, as opposed to the 2-wire design you mentioned. This simply means that they will ground through the mounting stud instead of using a dedicated ground wire. I have attached...
view full answer... - One Wire Clearance and Side Marker Light Options to Replace Lights on Horton Hauler TrailerWe have quite a few different options for trailer clearance lights with one wire and that will ground through the mounting hardware. These lights come in various sizes and shapes. The best replacement for your trailer will depend on the size light you are wanting to replace. For a small LED clearance light that is a stud-mount, you can use the Optronics Sealed Mini Rectangular LED Stud Mount Trailer Clearance Light. For an amber light you will want # MCL95AB and for a red light # MCL95RB....
view full answer...
Do you have a question about this Trailer Light?
Why etrailer.com?
At etrailer.com we guarantee:Highest quality trailer lights for the best price.
Our Lowest Price Pledge ensures you will never overpay for the parts you need.Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate trailer light information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Video Edited:
Zack K
Video Edited:
Patrick B
Video Edited:
Dustin K
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video by:
Joshua S
Updated by:
Laura H
Updated by:
Sarah W
Updated by:
Brian T
Installed by:
Cole B
Installed by:
Ryan G
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 800-298-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.