8-1/16" x 2-7/8" Rectangle. Waterproof lights act as brake, tail, turn, side marker, side reflex, rear clearance, rear reflex, and license plate light for trailers wider than 80". Surface mount - hardware included. 3-Wire pigtail.
Features:
Specs:
The waterproof construction of these lights make them ideal for use on trailers that may be submerged, like a boat trailer. Each circuit board is sealed, which means that water will not damage the diodes or circuit board.
If a trailer is 80" or wider at its widest point, then it requires rear clearance lights in addition to basic trailer lights. These clearance lights indicate the width of the trailer when it is viewed from the back.
To meet these requirements on a flatbed utility trailer where the bed extends past the wheels, you can install combination trailer lights that include the rear clearance function. For proper mounting, the lights must be installed at the widest points on the rear of the trailer - one on each corner.
A PC-rated light produces a 90-degree angle of light to either side of its centerline for a total of 180 degrees of coverage. This beam pattern can be clearly seen when you are standing directly in front of the light, as well as when you are standing on either side of the light. When properly installed, this type of light can function as both a front clearance light and a side marker light or as a rear clearance light and side marker light.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to be taking a look at the Optronics Over 80" LED Trailer Light Kit. This light kit is ideal for marine trailer applications. It's going to come with two red rectangular LED trailer lights. The passenger side light, or the right hand side light, is going to serve seven functions: such as your stop, turn, tail, rear clearance, rear reflex, side marker, and side reflex functions. The driver's side light's going to contain all the same as the passenger side light, plus your license plate illuminator or license plate light. The lights feature a sealed, waterproof construction that is submersible. They're going to feature replaceable lenses.
The LED system is encapsulated inside the unit. If you we're to take off the lens, what you would see is you would see is a nice, clear plastic; kind of like a bubble that goes over all the LED lights in the board and all that stuff, to keep it completely sealed. It's got that nice, sealed design, waterproof, can be submersed. If you end up cracking or breaking the lens, the lenses can be replaced. They're just held on there with four screws. The lenses are made from an acrylic construction.
The housings of the unit are made from plastic. It's a nice strong durable design that's corrosion resistant. It's a full LED system. LEDs are going to make great replacements for incandescent lights. They last longer.
They burn brighter. They're much more efficient. You don't have to worry about replacing bulbs. You don't have to worry about brittle filaments. The lights are going to contain a three-wire design. You're going to have your white wire for your ground wire; your brown wire is going to be for your running lights; for your passenger side light, you're going to have a green wire.
That's for the stop and turn lights. On the driver's side, you're going to have a yellow wire. That's going to be for the stop and turn lights. The lights are SAE and Department of Transportation Department compliant. They meet FMVSS and CNVSS requirements for automotive lighting. They are PT-rated as well as PC-rated lights. A few dimensions I want to go over with you real quick. We're just going to take a look at one of the lights, since they're both going to measure the same. The widest point is actually here at the front. They're a little bit more narrow at the back. At the front, the length is going to measure 8 1/16th of an inch long. Take a measurement of the height, so from top to bottom; that's going to give us a measurement of 2 7/8 of an inch. The depth, back to front; we're looking at 2 13/16 of an inch deep. The mounting slots on the lights, these are going to be separated on 2-inch centers. You're going to have three slots. Center on center is 2-inches. Center on center is 2-inches. Center on center is going to be 4-inches; again, three wire design. Your mounting hardware is included so it's going to come with your bolts. It's going to come with your nuts with serrated washers attached to them. With the kit, you're also going to get your wiring nuts, as well. When it comes to the number of LEDs that each light contains, this one is for the driver's side. This is going to contain 22 LEDs, so we're going to have 12 right here in the main body, 3 right here for the rear clearance, and then 3 for the side marker. On this corner, there's going to be 6; 3 on the front, 3 on the side. Then, on the bottom for the license plate light, we're going to have an additional 4; 2 diodes located on each side. For the passenger side light, we're looking at a total of 18 LEDs; 12 on the main body, and then again, 6 going around here on the corner; 3 on the front and 3 on the side. I do want to go ahead and hook it up to power, that way you can see what it looks like with power running to it. I'm just going to hook up the driver's side light. Again, the white wire's going to have a ring terminal already attached to it; that's going to be our ground wire. The yellow wire is going to be for our stop and turn signal. Then, brown wire is for our taillights. It sends out a really nice, clear consistent signal. Again, you can see all the LEDs right here. I'm going to bring it in a little bit closer so we can get a better look at it. We're going to have that main body. Then on the sides, you can see there's no lights on this side. Again, this is for the driver side. On the outer edge we're going to have three right here on the front, three right here on the side, reflectors are built-in to the lenses. On the bottom, we're going to have the license plate illuminator, or the license plate lights to send out a nice signal down towards the license plate. This is the taillight function, so when we activate our brakes, you can see how the signal output increase. Then, when we activate our turn signals, it's going to do that same thing. When it comes to the power draw, we're looking at 0.259 amps for the stop and turn lights, and 0.062 amps for the side marker and clearance lights. That's going to be rated at 10.8 volts. Optronics is going to put a lifetime warranty on the LEDs. That's going to do it today for the look at the Optronics Over 80" LED Trailer Light Kit. .
Average Customer Rating: 4.8 out of 5 stars (150 Customer Reviews)
8-1/16" x 2-7/8" Rectangle. Waterproof lights act as brake, tail, turn, side marker, side reflex, rear clearance, rear reflex, and license plate light for trailers wider than 80". Surface mount - hardware included. 3-Wire pigtail.Exact replacement for my utility traile r. 656196
Thank you etrailer. These tail lights were just as described and were delivered VERY VERY fast. I installed the on an old 2002 Tracker trailer as the old lights were old and rusty and only worked part time. Perfect fit - work great - LED lights are very bright. This is what you need to update an old trailer. 489951
My order arrived in good time and good condition, and the customer service here at etrailer was *superb*. Installation was ultra simple. It took far longer to break loose the old lights than to install the new ones. Very conveniently, the new lights have the same bolt pattern as the 20-year-old incandescent Wesbars they're replacing --and have a couple options for different bolt patterns were I installing them on a new trailer. The electrical leads are a good length --not too short/stingy with the wire. My only major complaint is that they came with wire nuts for connecting the leads to the harness, which aren't ideal for a submersible application, especially in salt water. I ended up using better, butt-end connectors that I had on my shelf. In an ideal world the manufacturer would have included two additions in the package: a packet of dielectric grease, for connecting the leads, and a simple rubber/plastic licence plate bracket to hang in the correct position under the left-side light (such as the original Wesbar lights had included). All in all, sitting here writing this ten minutes after I completed the job, I'm satisfied with the product. Hopefully they'll survive and perform as long and as well as the last lights did. 681891
These lights are great. Marker lights can even be seen in day light. Brake/Turn lights are very bright. Easy to install. These lights are for over 80" wide trailers, and are legal to run in my state for under 80" wide trailers. Very bright and would recommend to anyone that needs lights for there trailer. 504040
Recently bought a Boat with Easy Loader Trailer , both Tail Lights and side marking lights were corroded from Salt water use, in the process of rewiring the trailer , new lights arrived about week after ordering them, was a little disappointed when opening the new TLL160RK Tail Lamps as the Red lenses on both lamps were scratched during the shipping from the manufacturer to etrailer. I decided to go ahead and use them and very satisfied how they look , assembly was easy . These lights are excellent replacements for the old Wesbar lights that they replaced. 538854
Installation was dead simple, considering I've done it before. I bought a similar set of lights like this from a well known, budget quality tool store, which were rated to be "submersible." After the first summer, one was completely dead, and the other was flickering like crazy. I figured out when I took them off that the way they sealed them to be submersible was to hot glue them. That might work for colder climates, but when you take your boat trailer to the lakes along the Colorado River in Nevada and Utah, the temperatures at ground level over asphalt can get up to the 120-140°F range. It seems that they got so hot that the glue melted and allowed water to seep in, shorting the lights out and causing my problems. I'm hoping this set will last longer than a single season, but I won't know for sure until I run them. So far, just based on installation, they seem like quality components and so they get 5-stars. If I find out later that they can't take the heat, I'll see what I can do about adjusting my review. 512527
You can't go wrong with LED lights. This kit works perfectly. Easy installation. The wires are all color coded exactly except for 1 of 6 wires but nevertheless, no brainer. I also purchased shrink wrap butt connectors to keep the system water tight. These lights are bright and very visible. As always, etrailer is the best. I love ordering from etrailer. 509078
Carlos - 05/16/2019This is a replacement on a trailer I bought in January 2017. My trailer came with these lights. I backed into something that broke the lens and made replacement necessary. This, and the original, came with great engineering regarding the lighting bulbs, wiring, and waterproofness of the assembly. Unfortunately, to save a few cents on a $40 tom$60 retail item, the manufacturer chose to use bolts for attaching that quickly rust in salt water usage and become impossible to replace without total destruction of the unit and a hack saw to remove the bolts. Shame on the light producer for saving a few cents on bolts and nuts for an otherwise fine product. The accountants must be in charge. This is similar to outdoor furniture from China that comes with instantly rustable bolts and nuts. 659917
I am completely satisfied with the customer service I received from etrailer.com. All my questions were answered completely and I received my lights promptly. The price was very reasonable. My boat trailer is now street legal and very well illuminated!! 517466
I just installed these lights on a 2003 Karavan boat trailer, replacing the originals. The standard mounting slots and bolts matched perfectly with the trailer mounting plates, and the wiring color coding matched the trailer's too (perhaps those are somewhat standard?). So installation was simple and straightforward. The instructions included with the kit seemed adequate, but in my case they weren't really needed. These new lights are much brighter than the originals (sealed incandescent) and I expect they'll last much longer as well. Overall I'm very pleased with these lights. The quality seems good and the price reasonable (in my opinion). 442852
Have not installed lights yet. Replacing on a tilt trailer with LED lights. The amber side marker lights will need recepticals that I did order. I thought they would be ready to install, but they were not. 565693
Heather A - 09/17/2018I was looking to upgrade all of the exterior lights to LED on my 1986 Fleetwood 5th wheel. All was well until it came to the tail, brake and tail lights. Jameson at etrailer put in touch with the perfect product. Ordering was simple and delivery was expedient. Thank you Jameson and etrailer! 471803
David T - 01/31/2019the lites were the same brand and same size as the old ones were, so replacement was simple and led are much better than the old bulb type. I would recommend them any time and the service was great,thanks and i would order from you again. 432792
Excellent service. Ordered on a Sunday and was notified by George that it shipped same day. Everything is just as I ordered. Spent all day re-wiring boat trailer and lights and harness work great. Thanks George! 467128
James - 01/13/2019Package delivered promptly. Appeared packaged well. Lights installed easily and operate without issue whatsoever. I decided to purchase this particular brand from this particular retailer because of the lifetime warranty on the LEDs and etrailer's positive reputation. I am, however, a little disappointed that the lens of one of the lights looked a little scuffed up... as if it had been rubbing against the inside of the plastic packaging. I know things like this don't remain pristine forever, but when you purchase something new you want it to look that way! 435826
Looks like it did online, was easy to install and is real bright. Nice purchase 681818
Lights look great and well made. Lifetime warranty is a plus too. I think these were a better Choice than what was on Amaz0n. 524982
Parts were priced right and sent prompt ly. 568098
Excellent product. As advertised, waterproof and durable. 544802
I have not installed them yet but they look like the original lights . I bought lights from Walmart to save money . I installed the first light , it did not work . I could not figure out witch wire went where . After an hour switching wires , nothing worked . These lights are very clear where they go . I am sure they will be fine . 738558
Hardware rusted in one year. Rusted bolts and nuts. Lost ground contact. Changed to stainless hardware . Lights are Bright. 736014
These are very bright even in daylight. My use is on a boat trailer in a fresh water lake. No problems with submerged use so far. 732700
Great- no issues other than it was much less than what I could get locally. Thanks ET 728607
Worked as expected. 727898
As advertised, delivered on time, seamless transaction, EZ install, standard operating procedure for a purchase from etrailer. 727425
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Helpful Link
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.