What Is The Smallest Available Spindle Nut For 2.5k Axle?
Updated 03/17/2026 | Published 03/16/2026 >
Question:
I AM LOOKING FOR A PART NUMBER FOR THE AXLE SPINDLE NUT AND WASHER THAT HAS AN I.D. OF 3/4. WOULD FIT THE AXLE THAT USES THE DX22XR HUB. WE RUN INTO THIS SMALL SPINDLE EVERY ONCE IN A WHILE AND I CANNOT SEEM TO LOCATE THE NUT AND WASHER ON YOUR WEBSITE. THANKS! NATE
asked by: NATE P
Expert Reply:
Hey Nate,
We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut # 165931and a 1" washer # SW1000. I cannot find anything smaller.
Are you sure the threads on you're spindle are 3/4"? If they nut is actually 7/8", the above spindle nut and washer will be correct. The washer does not fit perfectly to the spindle, it is just there to give the nut more surface area to contact the bearing. Most 2k and 2.5k axles don't even use a washer to be honest.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- LM67048 / LM11949
- Standard Grade
- For 2500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Thinline LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 15 Diodes - Red Lens
- Search Results: 10~36 seal
- Shop: Thinline LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 9 Diodes - Red Lens
- Shop: 7-Way Round RV Style Trailer Connector - Trailer Side
- Shop: etrailer Electric Trailer Jack - Drop Leg - A-Frame - 18" Lift - 5,000 lbs
- Search Results: door hinges dump trailer parts
- Search Results: 40kadpf
- Shop: Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Search Results: studs
- Shop: Camco Replacement Lid for Jensen RV Roof Vent w/ Metal Base - Polypropylene - White
- Search Results: wheel studs
- Search Results: junction box
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Pre-Greased
- Search Results: 21~88
- Shop: Trailer Wiring
- Q&A: Is Socket Needed For Castle Nut on Trailer Axle e84YR
- Q&A: Replacement Hub Needed with LM67048 Inner Bearing and LM11949 Outer Bearing
- Q&A: Replacement Grease Seal For a Trailer Hub Using LM11949 Outer Bearing and LM67048 Inner Bearing
- Video: Ultimate Overview of the Curt 7-Way Trailer Plug Extension
- Video: An In-Depth Look at the Curt 7-Way Trailer Plug Extension
- Q&A: Trailer Idler Hub That Uses a LM67048 Bearing and Has a 5 on 4-1/2 Inch Bolt Pattern
- Q&A: Availability Of Trailer Hub With .75" Outer And 1.25" Inner Bearings
- Video: Comprehensive Review: T-Style Hook and Keeper Door Holder for RV or Enclosed Trailer
- Video: An In-Depth Look at the Buyers Products 90-Degree Door Check and Hold Back
- Video: What to Know About the Hook Probe Circuit Tester
- Q&A: Brake Controller Wire Functions By Wire Color
- Q&A: Parts Needed to Connect Gooseneck Trailer to Semi-Truck 7 Pole Round Plug
- Shop: Air Filter
- Article: 5 Things to Know About Weight Distribution Hitches
- Video: Comprehensive Review: Square Drop Leg Stabilizer Jack


Nate P.
3/17/2026
Yes Sir, the outer bearing is a LM11949 with an I.D. of 3/4" and the nut is the same size.