Upgrading Lights on 2000 Tracker PT175 Trailer to LED

Question

Question:

Jon, attached are the pictures that you requested. The top pictures are the front side markers and they have a Wes Bar # 3395. The other side markers with the posts/nuts and attached wiring do not have any part #’s and they measure 2 1/8 x 1 1/8. The passenger side rear light has a Wes Bar # 102641. I will also need any required pigtails etc. thanks Jon for the assistance.

asked by: Ernie S

1

Helpful Expert Reply:

We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I can be sure to recommend the correct parts.

expert reply by: Jon G

1

click to enlarge

Ernest

4/30/2019

Jon, attached are the pictures that you requested. The top pictures are the front side markers and they have a Wes Bar # 3395. The other side markers with the posts/nuts and attached wiring do not have any part #’s and they measure 2 1/8 x 1 1/8. The passenger side rear light has a Wes Bar # 102641. I will also need any required pigtails etc. thanks Jon for the assistance.

Jon G.

4/30/2019

Thank you for the pictures and the descriptions! For your Wesbar 3395 clearance lights you can use the Thinline LED Clearance and Side Marker Light # AL91AB. This is compatible with the Wesbar 108662 pigtail that I believe you are already using so this will be a simple plug and play application. For the other clearance lights we have the Optronics LED Clearance or Side Marker Light # MCL95AB that matches right up with the dimensions that you gave. This light has 1 wire and it grounds through the mounting hardware as opposed to your light that has a wire for power and a wire for ground. Then for your tail lights you can use the Optronics LED Combination Trailer Tail Lights # TLL160RK. These have the same dimensions as your current tail lights and it has a 3-wire design like your lights have. You should be able to cut the connectors off of your old tail lights and then splice them onto the new LED tail lights using Heat Shrink Butt Connectors # DW05744-5.

Answer 1

We have a few types of license plate holders to choose from and you can see all of them on the linked page. You might prefer one design over another for your Exiss horse trailer, such as the CE Smith Tread Plate design #CE26053A As for trailer lights…

view full answer...

Answer 2

I wouldn't worry about the trailer not having fenders. I've pulled a few enclosed trailers that were missing fenders and it didn't affect anything that I noticed. If you get a puddle or it starts raining the tires will fling water so it…

view full answer...

Answer 3

Hey Patrick. We get these questions quite a bit and it's typically a TDE Model LP7000 actuator. So, I am going to answer your question based on that. I would love to take a look at any pictures you have. You can send them directly to the email…

view full answer...

Answer 4

I took the measurements of the Multipurpose U-bolt, part #CE15504A, which you can see on the enclosed diagram. You'll note that the length of the U-bolt is 3 inches, which may be too short for your application. The closest sized U-bolt we are…

view full answer...

Answer 5

The Yates Rubber #YR8000 keel roller has a 3-3/8 inch diameter at the ends, a 2-1/4 inch diameter at the flat spot in the center and is 7-3/4 inches long. The roller would use a 5/8 inch diameter shaft such as part #CE10725A and would mount using…

view full answer...

Answer 6

To replace your old UFP A-70 actuator I recommend using the Dexter DX7.5L A-60 Brake Actuator - Bolt On - Drum - 2" Ball - Zinc - 7,500 lbs #DX33FR. This is going to be a direct replacement and will work with your drum brakes.

view full answer...

Answer 7

As I couldn't tell if the lights in the picture are LED or incandescent, I included with both options. For incandescent lights, you will need the Optronics Mini Trailer Clearance or Side Marker Light - Submersible - Incandescent #MC95RB for the…

view full answer...

Answer 8

I recommend using the Xtreme Off-Road Swing-Up Trailer Jack #ORJW350D as we do not have a jack which will fit the same weld on bracket you have on your boat trailer. This jack can be bolted onto your frame and will allow you to have more…

view full answer...

Answer 9

We've found that the amber clearance light from Optronics part #MCL95AB is very bright and easy to install so it would be a great choice for what you are looking for. I attached a picture that shows it on a smaller trailer for you to check out. I…

view full answer...

Answer 10

Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…

view full answer...

Answer 11

We offer weld-on and bolt-on trailer jacks that are similar to the Shelby 5764A jack you wish to replace but the jacks we offer are not exact replacements. We do have a jack that has a mounting plate similar to the Shelby mounting plate., It is part…

view full answer...

Answer 12

The psi of your trailer tires will be listed on the side wall. It will list the max psi which is what you will want to fill them to regardless of how much weight you have. For reference, the 4.80 x 12 tires we carry have a 60 psi max for load range B…

view full answer...

Upgrading Lights on 2000 Tracker PT175 Trailer to LED

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching