1. Home
2. Trailer Parts
3. Boat Trailer
4. Boat Trailer Parts

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

Hi Cliff; the inner diameter of the bearings used on 5,200-7,000 lb axles is the same so you can choose a higher rated hub to match the bolt pattern. You can use the Dexter Trailer Idler Hub Assembly - 5,200-lb, 6,000-lb and 7,000-lb Axles #42865-KIT…

A TPR roller like the #YR500YW-6P is going to be better than PVC. PVC is a cheaper product. TPR has the properties and performance of both PVC and rubber while having a higher tensile strength so it is going to be the most durable. I don't have a…

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

Tom, no the Replacement Mounting Hardware for CE Smith Roller-Style Guide-On #CE11451-A won't work with the Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers #CE27608PG. These are for roller style guide ons, like the CE…

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

Hi Cliff; the inner diameter of the bearings used on 5,200-7,000 lb axles is the same so you can choose a higher rated hub to match the bolt pattern. You can use the Dexter Trailer Idler Hub Assembly - 5,200-lb, 6,000-lb and 7,000-lb Axles #42865-KIT…

A TPR roller like the #YR500YW-6P is going to be better than PVC. PVC is a cheaper product. TPR has the properties and performance of both PVC and rubber while having a higher tensile strength so it is going to be the most durable. I don't have a…

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

Tom, no the Replacement Mounting Hardware for CE Smith Roller-Style Guide-On #CE11451-A won't work with the Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers #CE27608PG. These are for roller style guide ons, like the CE…

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…