Electric Jack w/ Footplate and 7-Way Plug - A-Frame - 25-1/8" Lift - 3.5K - Black
(1751 reviews)
Price: $190.68
In Stock
Electric Jack w/ Footplate and 7-Way Plug - A-Frame - 25-1/8" Lift - 3.5K - Black
Item # EJ-3527-BBX
Retail:$209.88
Our Price: $190.68
You Save: $19.20
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (1751)
- Q & A (0)
- Photos
etrailer Camper Jacks - EJ-3527-BBX
- A-Frame Jack
- Leveling Jacks
- Tongue Jack
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Electric Jack
- etrailer
- 1 Jack
- 25-1/8 Inch Lift
- Bolt-On
Electric A-frame jack has 2 toggle switches for operation. Jack has a retracted height of 9", an extended height of 28-1/2", and 19-1/2" of travel. Drop leg offers an extra 5-5/8" of lift. 7-way RV-style plug makes setup easy.
Features:
- Electric jack lets you raise and lower your A-frame trailer
- Drop leg allows for increased lift and saves time when raising or lowering
- Pin and clip holds leg at desired location
- 2 Toggle switches on the front of the housing let you operate the jack
- On/off switch controls light
- Extend/retract switch controls up and down movement
- 7-way RV-style plug pulls power from your vehicle's trailer connector
- No need to manually wire for power
- 7-Way must have active 12 volt pin
- LED light illuminates at a downward angle to help you focus on your coupler
- Emergency crank (included) allows you to manually operate jack if needed
- Black powder coated outer tube
- Zinc-finished inner tube and footplate resist corrosion
- Simple, bolt-on installation
Specs:
- Bracket height:
- Retracted: 9"
- Extended: 28-1/2"
- Total lift: 25-1/8"
- Screw travel: 19-1/2"
- Drop leg travel: 5-5/8"
- Clearance:
- 20-1/2" From bottom of bracket to top of jack
- Outer tube diameter: 2-1/4"
- Inner tube diameter: 2"
- Hole spacing on drop leg: 1-7/8"
- Footplate diameter: 5-1/2"
- Lift capacity: 3,500 lbs
- 1-Year warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
EJ-3527-BBX Ram Powered Jack w/ Footplate and 7-Way Plug - Drop Leg - A-Frame - 19-1/2" Screw Travel - 3,500 lbs - Black
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
- Defective
- Arrived Damaged
- Wrong item was ordered
Customer Reviews
Electric Jack w/ Footplate and 7-Way Plug - A-Frame - 25-1/8" Lift - 3.5K - Black - EJ-3527-BBX
Average Customer Rating: 4.7 out of 5 stars (1751 Customer Reviews)
Electric A-frame jack has 2 toggle switches for operation. Jack has a retracted height of 9", an extended height of 28-1/2", and 19-1/2" of travel. Drop leg offers an extra 5-5/8" of lift. 7-way RV-style plug makes setup easy.by: Charles02/14/2024
The 7-way plug electric jack is a great replacement for my crank handle jack. I did not want to install and maintain a 12V battery for just a jack so this is an easy plug and play solution for me.
by: George01/26/2024
7 pin easy hook up for trailer jack does not work on my 2020 ford ranger. Missing 12v power to jack control? any advice in Trouble shooting. Is there a compatibilty problem with ranger to your jack 7 pin config? Will use manual hook to battery rather then ask for replacement jack if possible?. Before I cut any wires and void warranty. Is all I have to do is cut and splice the fused red wire to a positive battery terminal to do this. What abount grounding? Please advise should I modify and wire direct or return jack back for refund/replace
by: Alan08/04/2023
Shipped quickly and arrived a day early. Jack has ample power and is fairly quiet operating.
If your 7 pin plug is not supplying 12v power, check the fuse box under the hood for an open 40A fuse. Placement will differ on vehicle/models but on my 2002 Silverado it is stud #1. It was pinned from the factory but never had a fuse, 12v power supplied after fuse was installed.
by: Ken02/24/2023
So far so good! I really like the 7 pin pigtail, eliminates cutting into the trailer’s wiring harness. Clean and tidy in appearance.
by: AC04/12/2024
Worked perfectly, handled my trailer no issues, just remember to unplug it before you pull away from your parked trailer, don't ask me how I found that out...
by: Paul03/28/2024
After only using the unit a few times, it stopped working because of the low quality power connection. We replaced it with a more durable version in order to get our toyhauler hitched back up to move.
by: David04/05/2024
Bought it to replace the OEM-installed fancy electronic-controlled jack that either would not work, or worse yet it jacked up the trailer on its own!
This one is basic. No fancy electronics to fail! Easy to install. Works perfectly as advertised.
by: David11/08/2023
Installed this today on a cargo/work trailer that I pull with a 19 f250, install wasn't bad, except for the trouble shooting. Just happen to notice they had one with a 7 pole wire, which I got so it'd work off my truck(since I have a cargo and no batteries), I'm pretty mechanically inclined and started troubleshooting what the issue was as soon as it didn't work. I had to change terminals for the hot wire to my parking light terminal, only way it'd work. Other than that, works amazing and regret not getting one sooner.
by: Terry M.01/19/2024
I ordered the etrailer jack after doing some research. The installation was simple and straightforward. I have a 2018 GMC pickup and 24' ATC trailer. When the jack is installed as intended, my tailgate would hit the jack housing. So, I slightly elogated the mounting plate holes and rotated the jack 1/3 turn...problem solved! A nice surprise was that the manual cranking feature works very easily, less effort than the original hand crank that came on the trailer. Some reviews I had read complained about the slow speed of the jack. I did not find that to be a problem. While it is not fast, you won't get in trouble and it beats the heck out of manual cranking. I'm happy with the purchase and would recommend it to anyone.
by: Kyle10/02/2023
Ordered on Friday at 4:00PM. Shipped on Friday and arrived on Monday afternoon. Great service and quick shipping are what you can expect from etrailer. I installed the jack on a 7x14 cargo trailer that I use to haul misc. equipment and materials with a 2018 Ford F350 DRW using a Curt 48012 pintle/ball combo hitch. Once the old jack was removed, installation was very easy. I did however have to make a modification to the jack. My tailgate would not clear the jack when mounted in its intended position. With kids and misc helpers that is a no go for me. After looking at the jack, I removed the 5 screws holding the top cover on and noticed there are 4 socket head bolts holding the gear box onto the jack body. I removed the bolts, rotated the gear box around to the back of the jack and reinstalled. This position provides me clearance for my tailgate and protects the switches from potential damage. It does put the light on the wrong side to be useful, but as the etrailer employee said in the video, “its not the brightest light” to begin with. I have only used it a few times to confirm operation but so far it works well and sure beats the old jack I had on there. etrailer has great customer service and technical support. I would recommend this product to others and will continue to shop at etrailer. Thanks!
by: Darryl R04/11/2024
Hi Chelsea:
Order did arrive on Wed. & in good shape.
Have only had a brief moment to look at it.
From what I see so far.....looks like it will
fit. (the jack's top housing, clearing the front
support on my generator mount).
Hope to install it this weekend.
Thanks, reconnect later.
Darryl
by: John07/30/2023
Arrived on time, no damage, instalation under 30 minutes, works as advertised. Only issue was the 'stop here' tape near bottom of the shaft was skewed. I know from past experience not to lower the Jack all the way down but am awaiting a reply from my email asking for info on exactly what point I should not lower the Jack. Other than that, I am very satisfied with the product.
by: Ron 02/10/2024
After a year still works great……easy to install, and didn’t need the light because I had already installed a rear utility light to my truck to hook up trailers but for those who don’t have a back light it is much easier than a flashlight. Great product!
by: Frederick02/23/2024
it's finicky often leading to holding your break whether it will work. The plug can be responsible sometimes for that but if it sitting a while it gets sticky so a good bit of use and service is needed. etrailer has been fantastic customer support when needed.
by: Kris02/19/2023
Very easy install. Works amazing. I love the 7 way plug that powers it. Very simple to use.
by: Ed01/06/2024
Did not fit .Sanded the power coat down trying to get enough clearance Clarance haha and it still doesn’t fit so close so I guess I will sand some more. What is odd is that this is specific for my camper as per previous question as to fit.Paint remover maybe offer any suggestions
I already have over an hour in this and it still isn’t installed.
Thanks
by: Steven 05/15/2024
So far, the jack is performing as it should. It levels up our camper quickly and easily.
by: Dennis 03/29/2024
Works great on my 24' car trailer!
by: Andra03/13/2024
Best purchase I have ever made and I will never have go without one on my horse trailer ever again!
by: Richard04/21/2023
This is a good little jack! It came from etrailer quickly, installed easily, and works great! As usual, the folks at etrailer were a pleasure to work with!
by: Julie 04/04/2024
Package was delivered on the day that was scheduled. Very happy with the jack. It was very easy to install. Thank you so much.
by: Kevin 04/01/2024
It came to me with the light assembly broken due to shipping. The company forwarded me a new cover right away and I changed it out. Looks and works great
by: Gregg12/02/2023
Does not work when connected to my 2024 GMC Denali 3500HD, required an LED Load Adapter on the 7-way connector
by: David08/03/2023
Seven blade plug was miss wired. I had to disassemble and contect wires to correct location. Involved locating "hot" pin and then ground. This was complicated as new vehicles have so much plastic, it was difficult to get a ground for test light. High level of frustration. Cheap shielding for wires from plug to jack. Cheap plug, but works. Unit now works. Apprehensive about reliability.
Katrina D.
8/8/2023
That is not good that you had to go through all of that extra work. Let me see if there is anything that we can do for you.
by: Fotios08/19/2020
Great looks. Powerful Jack. I mounted a dedicated battery to it so I would not have to depend on my vehicle’s thin wiring. Questions that I had during the installation were promptly and professionally addressed by etrailer’s technical dept. amazing help and support. Thanks
Fotios
8/23/2021
This jack is amazing. Gets a regular workout and still works great a year later.
25
1745
Show More Reviews
See what our Experts say about this etrailer Camper Jacks
- Recommended A-Frame Electric Jack for Horse Trailer with Living QuartersIf you are looking for an a-frame electric trailer jack for a horse trailer with living quarters, you are going to want to go with a heavy-duty option because of the heavy tongue on the trailer. The heavier you go, the longer the jack will last as it does not have to work as hard and the faster it will extend and retract. The Stromberg Carlson Electric Trailer Jack part # JET-5000 is what I recommend because of the 5,000 lb weight capacity. That said, you could go with the Electric Jack...
view full answer... - Installing The etrailer Electric Trailer Jack On A Trailer Tongue With Excessive Powder Coating The outer tube of the Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX is 2-1/4" in diameter, which is a standard diameter for most tongue-mounted trailer jacks. If the paint on the trailer tongue is preventing the tube from sliding through the hole then you'll unfortunately need to sand through it or use a grinder to cut through the excess until you can get the jack to pass through. Once you get the jack installed I recommend touching up the paint to help prevent any rust or corrosion...
view full answer... - Is There An Electric Motor Compatible With The Buyers Square Jack 3370091415HWhile we do offer several other powered jacks, we do not have a motor that is compatible with the buyers # 3370091415H at this time (July 2023). The only powered jack we have are either a-frame style like part # EJ-3527-BBX, or fifth wheel landing gear like # UF17-943010.
view full answer... - Recommended Electric Trailer Jack W/ 7-Way Connector For 24' Cargo TrailerWe have the exact jack you are looking for. I recommend the etrailer Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX which has a 3500lb weight capacity and has 25-1/8" of lift making it perfect for your 24' cargo trailer. The # EJ-3527-BBX has a 7-way connector which plugs in to the 7-way connector on your tow vehicle allowing you to lift or lower the trailer without needing to connect it to an on-board battery. I included a video of the etrailer # EJ-3527-BBX for you to take...
view full answer... - Distance from Jack Foot to Mounting Bracket on Electric Jack EJ-3527-BBXThe bracket height or distance from the mounting plate to the bottom of the jack foot on the Electric Jack part # EJ-3527-BBX is 9" while retracted. I have attached for you below a photo with this dimension.
view full answer...
- Troubleshooting etrailer A-Frame Powered Jack Not WorkingTry cleaning the pins of the 7-way connectors on your vehicle as that's most likely what's preventing the etrailer jack # EJ-3527-BBX from working. Also make sure the battery on the vehicle is in good shape and that the 12 volt power circuit pin (1:00 position) has 10 gauge wire like part # 10-1-1 ran from it to the battery.
view full answer... - Adding An On-Board Trailer Battery to Trailer for Electric Power Tongue JackA 100 amp hour battery would suffice for powering a trailer tongue jack as well as some other accessories. For this, we have both AGM such as the Bright Way Deep Cycle RV or Marine Battery part # BRW94FR. In order to charge these batteries, you'd need to tap into the trailer connector's battery charge line circuit. This is only present on seven way connections so if you don't yet have one you'll need to upgrade using the Trailer Wiring 7-Way Upgrade Kit part # HS381-9000 which is for the...
view full answer... - Replacement Jack Options For a 2012 Casita Spirit DeluxeBased on images I can find for your 2012 Casita Spirt Deluxe it appears it came with a standard top wind jack like the # TJA-2002-B. Unfortunately, there is not a database like you have with cars to lookup parts since RV manufacturers do not keep these records and will constantly change parts depending on what is available. This may or may not match exactly what you currently have on your camper as it is 12 years old and could have been changed since it was new. As these are a mostly universal...
view full answer... - A-Frame Tongue Jack Recommendation with Drop LegWe do have a variety of A-Frame tongue jacks that come with a drop leg. Out of our linked selection I recommend going with out 3.5K electric trailer jack which comes as a hardwire install as part # EJ-3520-BBX or a 7-Way plug-in install as part # EJ-3527-BBX. These are standard electric jacks that use a pull-pin you remove to drop the leg. If you're looking for something with higher quality then you'll want the Bulldog Powered Drive Trailer Jack # BD500199 which is rated for 4.4K lbs...
view full answer... - Can the 7-Way Plug On the Electric Jack w/ Footplate EJ-3527-BBX Be RemovedThe Electric Jack w/ Footplate is offered both with the plug part # EJ-3527-BBX and without the plug part # EJ-3520-BBX. Therefore, if you wanted to go with the model that has the plug and just cut that off you would indeed just run the wire to the battery or you can go with the model that has the blunt cut wire which is more cost effective.
view full answer... - How Far Should You Retract A Ram Electric Trailer Jack The Electric Jack w/ Footplate and 7-Way Plug - A-Frame # EJ-3527-BBX should stop before it reaches the pin and clip that holds the drop leg. Most people will typically stop as soon as they're a few inches above the ground to avoid having to wait for it to fully retract as long as it will clear while towing the trailer. The sticker is mostly there to prevent people from pinching down on the pin and clip and is more of a guide.
view full answer...
- Why Does Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX Come with 7-WayThe Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX has a 7-way for powering the jack and was designed to plug into your vehicle 7-way when needed to raise and lower and then when you go to tow you'd plug your trailer 7-way back in. We have a similar jack that was designed to hardwire to the trailer wiring with the part # EJ-3520-BBX.
view full answer... - Recommended Electric Trailer Jack With 7-way Connector and Protective CoverThe Electric Jack w/ Footplate and 7-Way Plug - A-Frame - 25-1/8" Lift - 3.5K - Black # EJ-3527-BBX you were looking at has the foot plate and 7-way connector you were wanting, and you can use the Ultra-Fab Protective Cover for Electric A-Frame Jacks # UF38-944020 to protect the jack from the elements. I included videos of the products mentioned for you to take a look at.
view full answer... - Can etrailer EJ3527-BBX Trailer Jack Be Powered From 7-Way Trailer Connector on 2020 Ford F-150The etrailer brand # EJ-3527-BBX is equipped with a 7-way plug that technically can be plugged into the 7-way trailer connector on your 2020 Ford F-150, but it will not function due to the "intelligent" towing package these come with now. This makes your towing functions only operate when your truck detects a trailer with electric brakes. This being said, your best bet would be to install a battery on the trailer and run a powered jack from that. The etrailer # EJ-3520-BBX jack is designed...
view full answer... - Replacement Power Switch for a Ram 3,500 lb. Electric JackIf your Ram 3,500 lb. electric jack looks like the Electric Jack w/ Footplate part # EJ-3520-BBX, # EJ-3527-BBX, or # EJ-3520-WBX then the Replacement Power Switch for RAM Electric Trailer Jack with Footplate # EJ-3520-PSW is the correct replacement switch. If you do not have one of the above jacks and could send me pictures of your jack and switch, I would be happy to help look into this further.
view full answer... - What Electric Tongue Jack Can I Use On A 2020 Palomino Puma Travel TrailerUnfortunately Palomino does not list that spec for their trailers. Generally it will be a 2-1/4" hole but this is not exactly universal. Most of the jacks we carry will fit a 2-1/4" hole like the # EJ-3527-BBX. We have a few jacks like the # 3370093500 which require a 2-1/2" hole. For a camper like your 2020 Palomino Puma with a hitch weight around 620 lbs, a 3,500 lb electric jack will be plenty strong.
view full answer... - Power Connection for etrailer Electric Tongue Jack EJ-3527-BBXThe etrailer electric tongue jack # EJ-3527-BBX has a pre-wired 7-way plug like part # H20046 that saves you the hassle of hard-wiring the jack to its power source. It can receive its 12V operating power either from your tow vehicle's 7-way socket which uses 12V power from the vehicle battery, or it can be powered from a secondary 7-way socket you could install on your trailer, along with a trailer-mounted battery. You could use 7-way part # HM48480, which includes a mounting bracket...
view full answer... - Troubleshooting an Electric Trailer Jack That Gets Power But Sounds Like It's ShortingIt sounds like you have an issue with the buttons since your jack is getting power but when you use the buttons is when you hear the shorting sound. I recommend popping out the original buttons and inspect the connections to make sure they're secured correctly and there is no exposed wires. If you come to the conclusion that you need to replace the buttons, then you can use the Replacement Light Switch for Electric Trailer Jack with Footplate # EJ-3520-LSW for the light switch and #...
view full answer... - Can etrailer Electric Jack Install on Trailer that Has A-Frame Mount But Also Frame Mounted JackSince the a-frame jack mount of your trailer isn't in use right now you could certainly use the Electric Jack with Footplate part # EJ-3527-BBX to help make the trailer easier to jack up and down. Your other jack would not be affected by this one at all.
view full answer... - Recommended Electric A-Frame Trailer Jack for a Forest River Rockwood High WallThe Electric A-Frame Trailer Jack with 7-Way Plug part # EJ-3527-BBX would be an excellent option for a Forest River Rockwood High Wall (All Models). The Electric A-Frame Trailer Jack has a 3,500 tongue weight rating so this would far exceed the tongue weight rating of any Forest River Rockwood High Wall. The higher rated the weight capacity of the trailer jack is in relation to the tongue weight of the trailer, the longer the trailer jack will last so the Electric A-Frame Trailer Jack...
view full answer... - Replacement Electric A-Frame Trailer JackThe triangular pattern you see on the # 322-RDJ-2K and your trailer is pretty standard for A-frame trailers. For an electric jack that will fit this same pattern I recommend the Electric Jack w/ Footplate # EJ-3520-WBX. This has a retracted bracket height of 9", extended height of 28-1/2", and 25-1/8" of total lift. It also has a 3,500 lb capacity. This is also available in black # EJ-3527-BBX which includes a 7-way so you don't have to manually wire it for power. I have attached some...
view full answer... - Can the Ultra-Fab 4K Electric A-Frame Jack Be Powered From the VehicleYes, the Ultra-Fab Electric A-Frame Jack part # UF38-944016 can be powered from the tow vehicle's battery. I suggest simply attaching a trailer connector to the end of the power wire and extending if needed, similar to the etrailer Electric Jack with Footplate and 7-Way Plug part # EJ-3527-BBX. That said, the Ultra-Fab pulls more power than the etrailer so you really can't use the 7-way socket due to the wire gauge difference. I recommend installing part # PK11852 on the jack and part...
view full answer... - Is There a Drop Leg Attachment for the Trailer Valet JXC Trailer JackI do have an option for you but there isn't a drop leg available for the Trailer Valet JXC Trailer Jack part # TV54FR or part # TV94FR. If you're after faster operation or less work then you may want to take advantage of the drill powered operation using the Drill Attachment part # TVDA. The other option is to simply go electric using the Electric Jack w/ Footplate part # EJ-3527-BBX which has the same benefits as using the drill attachment but with a lot less parts.
view full answer... - What is Bolt Pattern of Powered A-Frame Jack # EJ-3527-BBXThe Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX uses the standard 3 inch A-frame jack mounting pattern. The holes are slightly slotted too which means yours measuring 3-1/4 inch would fit just fine.
view full answer...
Do you have a question about this Camper Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Expert Research:
Adam R
Edited by:
Lindsey S
Installed by:
Jeff D
Installed by:
Randy B
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Matthew E
Video by:
Zach D
Written by:
Mike S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
1/31/2024
Thanks for reaching out! What I am going to tell you to do first is check the fuse box for your Ford and make sure that is a fuse there for the 12-volt function. From time to time some Ford trucks do not have this fuse active. Also, you can do what you mentioned by running the power to a 40-amp circuit breaker like part # 9510 to the positive terminal of the battery. The jack would be grounded through the seven way.