Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs
(76 reviews)
Price: $405.54
In Stock
Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs
Item # F141401
Retail:$831.77
Our Price: $405.54
You Save: $426.23
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (76)
- Q & A (0)
- Photos
Fulton Trailer Jack - F141401
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Utility Trailer
- 2001 - 3000 lbs
- Electric Jack
- Bolt-On
- Leveling Jacks
- Tongue Jacks
- 22 Inch Lift
- With Round Foot
- Steel
- Fulton
This electric side-mount jack offers 14" of screw travel. Spring-loaded pull pin quickly releases the 8" drop leg. 3 LED lights allow easy setup at night. Sealed surfaces resist corrosion. Fits 3" to 5" trailer frames.
Features:
- Electric marine jack lets you lift and lower your trailer quickly and easily
- Powered drive provides quiet operation and efficient use of electrical power
- No more hand cranking
- Weatherproof on/off and retract/extend toggle switches are easy to access
- Automatic-reset circuit breaker prevents overextension
- Self-healing Sharkskin finish offers a 1,200-hour salt spray rating on exterior jack surfaces
- Ideal for use on a boat or snowmobile trailer
- Durable enough for saltwater applications
- Clear ZMax finish offers a 600-hour salt spray rating on internal components
- Black housing with sleek design protects motor
- UV- and impact-resistant thermoplastic construction
- Durable stainless steel ACME screw resists corrosion
- 3 LED lights make it easy to set up at night
- 4" - 6" Overlap of tubes at full extension provides additional support for side loading
- Spring-loaded pull pin quickly releases the drop leg into position
- No more worrying about losing the pin
- Emergency, ratchet-style crank socket
- 3/4" Deep well socket inserts into end of drive collar - ratchet clockwise to retract, counterclockwise to extend
- Simple bolt-on installation to the side of your trailer
- Zinc-coated mounting brackets and hardware are included
- Wires to 12-volt power source
Specs:
- Application: fits 3" to 5" trailer frames
- Bracket height:
- 9-3/4" Retracted
- 31-3/4" Extended
- Total lift: 22"
- Screw travel: 14"
- Drop leg travel: 8"
- Inner tube diameter: 2"
- Outer tube diameter: 2-1/4"
- Lift capacity: 2,500 lbs
- Footplate diameter: 5"
- 5-Year limited warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
141401 Fulton XLT Powered Drive Marine Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs
California residents: click here
Customer Satisfaction Score:
95% were satisfied with this product
5% of customers were not satisfied
- Arrived Damaged
- Defective
- Wrong item was ordered
Customer Reviews
Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs - F141401
Average Customer Rating: 4.7 out of 5 stars (76 Customer Reviews)
This electric side-mount jack offers 14" of screw travel. Spring-loaded pull pin quickly releases the 8" drop leg. 3 LED lights allow easy setup at night. Sealed surfaces resist corrosion. Fits 3" to 5" trailer frames.by: Cal09/02/2023
easy to install, great sharkskin finish ,works perfectly on my 7000# camper trailer, quiet very pleased with this jack.
by: Quez07/11/2022
Used on Hoosier pontoon trailer (BX325TT-12).
Clamped to center 4 x 3" tube.
by: FastDawg07/14/2022
I installed this on my aluminum trailer that met the tongue weight criteria. I have ordered a solar panel to place on top of the storage box to maintain the battery.
by: Gary 10/11/2023
When first used it didn’t work, put a snowmobile battery hooked up and it started working now it works off the truck as it should
by: Shirley 06/27/2023
For a couple in their 60s, this electric jack on our 11,000lbs boat keeps allows us to continue enjoying the sport of boating.
by: Tom04/29/2020
Installation was a breeze and only required a few common household tools....
As you can see by the before and after pictures the finished product looks great and works better than I anticipated AND the best part about my new electric trailer jack is no more cranking on that old manual trailer jack.
by: Rob 08/25/2022
This is a very effective trailer jack. Easy to mount...easy to operate. Plenty of power to lift the bow of my 23' Sea Chaser. The older I get, the more lazy I get. (LOL) So this is the perfect tongue jack. I connected mine to a small solar charger and a small 12 volt battery and it's ready to go whenever I need it. Very nice jack. No problems so far. Highly recommended. The only small setback is that you have to align the hitch ball very close to the tongue...it's not easy to move the tongue over to the hitch. I guess that goes with the territory. If you're good at backing up to it, it takes less time. Maybe if it came with a wheel(s) rather than the pancake stand...it may make it even better.
by: Duncan R08/30/2023
Easy to install, Easy to operate
by: William 09/19/2022
The first one I bought broke, remounted the second one on the trailer further forward on the trailer reducing the weight. Works great.
by: Jason 04/05/2023
Very fast shipping and easy transaction! Always use etrailer!
by: Josh 09/18/2022
due to shoulder problems, i decided to replace my manual jack with this. Glad i did!! This item is great and very easy to operate. I wont have another boat trailer without one
by: Tom 06/28/2023
Works great!
by: Gary 10/25/2022
The jack arrived a day early. A nice start. Installed easily with no surprises. Lifts our two horse trailer effortlessly.
by: Thomas 09/09/2022
Mounting u bolts were not strong enough. Had to buy a stronger set locally. I went to a grade 8 u bolt.
by: Francis 07/13/2023
Great customer service
by: 10/05/2021
Used 6x bought 6 months ago and stopped working. No light at all. There is no information any where on how to troubleshoot this. I emailed customer support and the company is a joke. I have since emailed 4x asking for help and for them to contact me with any info. Can you imagine a jack failing like this and them never answering your contacts. The only email I got was we received your email and our warranty group is busy right now. That’s it. Jacks are so important to using your RV don’t trust your precious time or headaches to a company that doesn’t stand behind their products. I had read other bad reviews but decided to try it thinking I would get a few years but it didn’t even last 6 months. And I thought the company would stand behind the product but I was so wrong.
Jenny N.
10/14/2021
We will have customer service contact you.
by: Randy S11/14/2019
Installed on 14’ open/flat bed, tandem wheel trailer, for non-marine use. Trailer stored outside when not in use. No deterioration from being in the elements. Looks new. Easy to install. Has functioned flawlessly during first year of use.
Randy S.
11/15/2020
Reliable. No issues 1 yr+ service. Well worth cost in reduced effort ability to easily manage challenges of uneven, wet terrain without frustration.
by: Kelli H01/27/2020
My husband hurt his back and could no longer help me hitch and unhitch their boat, and I was really struggling to do it by myself... this motorized jack was an answer to my prayers. I have a 20’ Mastercraft X2 wakeboard boat and this jack handles it without any issue. My husband used the included wires to hook up a connection which plugs into the connection at the back of the truck where the trailer lights connect- I think this might take some electrical knowledge but works great for us.
by: William G.04/14/2021
it was very easy to install and it works great, a lot easier than cranking the trailer wheel up or down
William G.
4/16/2022
Great
by: Mr. Kelly04/16/2022
The salesman told me that if I could find it for a cheaper price somewhere they would honor that plus give me back 15% more of the original price. I found it for a cheaper price. I called etrailer. A gentleman emailed me a website to go to fill out the form with the information and within days had refunded me the difference plus the 15%. I have bought many things from this company. They have a great reputation.
by: Victor 04/24/2020
Amazing so far and wishing I had done this a LONG time ago! It's understandably slowish, but who cares. Super easy. Flip the switch and sit back. I power mine with a portable jumper box from Harbor Freight so I don't have to worry about a battery getting stolen off the trailer.
by: Carl 02/17/2021
Works well as it should! No problems at all 1 year out. As I have it powered by the same power as my trailer tilt battery, it is always powered for use. I don’t really use the light so no comment there. Adequate lift with a well loaded trailer. I do wish it was a little faster, but not a big issue.
by: Kevin 08/23/2021
Very easy to mount. Seems like a well built product and it is working well. I have it on a 28 foot boat trailer and my only complaint is that is seems a bit weak lifting it up. I mounted a standalone battery on the trailer so I do not have to use the vehicle power. It still moves it up fine but seems like it is struggling a little.
by: Chris09/08/2021
Looks lik3e a good product. Shipping is a different story. Box was ripped open at one point and somebody taped it up (shippers don't do this. Missing a two of the mounting nuts.
Brooke M.
9/16/2021
Thank you for your review! Our customer service team should be reaching out to you in the near future.
by: Bill09/02/2021
I was unsure as how to rate this order. etrailer did an excellent job in taking and processing my order. On the other hand, there were issues with shipping. My order was delivered to the wrong address, the box was very badly damaged and missing a part. I have installed the jack and it appears to be working.
25
76
Show More Reviews
See what our Experts say about this Fulton Trailer Jack
- Backup Brake Battery for Powering Trailer Jack Thanks for the picture. Yes, that battery will be able to power the Fulton XLT Powered Drive Trailer Jack item # F141401.
view full answer...
- Dimensions Of Head Assembly Of Fulton XLT Power Jack F141401I had our warehouse measure the Fulton XLT Powered Drive Trailer Jack # F141401 you were looking at and it has the following measurements. From top of mounting bracket to top of head assembly is 21", from the front to the back of the head assembly is 7", and the width of the head assembly is 2" as you can see in the included diagram. I included a video of the # F141401 for you to take a look at.
view full answer...
- Can Fulton XLT Powered Drive Trailer Jack Install Backwards on Trailer FrameThe head of the Fulton XLT Powered Drive Trailer Jack # F141401 that you referenced is not reversible on the rest of the jack assembly but you can install it backwards on the side of the trailer you want to install it on without issue.
view full answer... - How Does Fulton XLT Trailer Jack Wire to Trailer 7-WayThe Fulton XLT jack part # F141401 would need to run to the 12 volt accessory circuit of the 7-way on the trailer for the black wire and then to the ground circuit for the white wire. If you check out the attach diagram you'll see where these circuit are.
view full answer...
- Fulton XLT Powered Drive Trailer Jack for a CamperYes, the Fulton XLT Powered Drive Trailer Jack item # F141401 can be mounted on a camper. You will need to verify it will fit your tongue first. The bracket that mounts the jack to your trailer is made for 3" x 3" to 3" x 5" frames. This jack will allow up to 22" of lift using the 8" drop leg and 14" of screw travel. It has a 2,500 lbs capacity.
view full answer... - Recommended Electric Jack for Boat Trailer For an electric jack that will work great with your boat trailer, I highly recommend the Fulton XLT Powered Drive Trailer Jack # F141401. This is an electric, side-mount jack that will provide you with 14 inches of travel and a lift capacity of 2,500 pounds. This high capacity will allow the jack to work well below its limits on your trailer, which will lead to a longer lifespan. The jack also features a self-healing Sharkskin finish with a 1,200-hour salt spray rating that makes it ideal...
view full answer... - Can Motorcycle Battery Be Used to Power Fulton F141401 Powered Side-Mount Trailer JackThe Fulton # F141401 XLT Powered side-mount trailer jack has a lift capacity of 2500 lbs, so it will handle your trailer's 1100 lb tongue weight with no problem whatsoever. The jack draws 15 amps, and you'd want a battery that had a minimum 150 amp hour capacity for best function. You'll find that you won't get very many cycles out of the motorcycle battery before needing to recharge it. You'll be better off using a car battery instead. If you click the provided link, you can see a product...
view full answer... - What Diameter U-Bolts Does Fulton Jack # F141401 Include?I went out to the warehouse to measure the U-Bolts included with the Fulton Jack # F141401 and found they are 3/8" in diameter.
view full answer... - Where are Bracket Height Measurements of Fulton XLT Marine Jack Measured FromThe bracket height dimensions of the Fulton trailer jack # F141401 that you referenced are measured from center of the mounting bracket of the jack down to the bottom of the jack foot. So it would be 9-3/4 inches from center of bracket to ground retracted and 31-3/4 inches when extended. This does mean you could get your trailer's tongue 31-3/4 inches off of the ground.
view full answer... - How To Obtain Replacement U-Bolts for the Fulton XLT Powered Drive Trailer JackI checked with Fulton and they don't offer replacement u-bolts for the Fulton XLT Powered Drive Trailer Jack part # F141401. That said, we do offer plenty of replacement u-bolts that could be used with said jack you'd just need to measure and then choose the correct replacement from the list below.
view full answer... - Is There Any Way To Mount The Fulton XLT Powered Drive Trailer Jack # F141401 on 7-1/2" Tall Frame?There are a couple options to mount the Fulton XLT Powered Drive Trailer Jack # F141401 onto your 7-1/2" tall frame. The mounting bracket along with the included hardware only allows for mounting to a 3"-5" tall frame. You can either drill through your frame and insert sleeves which will allow you to bolt the mounting bracket to your frame without crushing the frame. Otherwise you will need to create a mount adapter using a couple larger plates of steel you can bolt to the jack and are...
view full answer... - Securing Fulton XLT Powered Drive Trailer Jack # F141401 To Trailer Parked In Public LotThe head of the Fulton XLT Powered Drive Trailer Jack # F141401 is not easily removable as it is connected internally to the jack tube. You would have to remove the entire jack if you are concerned about it being stolen while in the trailer parking area. You could also have the mounting bracket welded to the frame to make it impossible to take the entire jack without grinding off the welds.
view full answer... - Can Fulton XLT Powered Drive Trailer Jack Be Powered by Truck's 7-Way Connector The 12V circuit from your truck's 7-Way isn't typically the best source to power a higher-rated accessory like the Fulton XLT Powered Drive Trailer Jack # F141401 that you referenced. You might be able to operate the jack in this manner but it will likely be slow going and you may blow a fuse under the hood depending on the type of load you're looking at. The best way to power an electric jack really is with a dedicated 12V battery like you mentioned. This will ensure quick and reliable...
view full answer... - Mounting Bolt Pattern on Fulton XLT Trailer Jack # 141401The Fulton XLT Powered Drive Trailer Jack # F141401 has a bracket that is made for 3x3 to 3x5 inch frames using the included hardware. It can use other hardware as needed for your application and the mounting holes are 5-1/2 inches on center wide and 1 inch on center vertically with the exception of the space in the middle being 1-7/16 inches on center. I've attached a diagram and a video to assist.
view full answer...
- Amperage Draw For Fulton XLT Powered Trailer Jack and is Circuit Protection NeededI spoke with my contact at Fulton and he told me that the max amperage the Fulton XLT jack part # F141401 would draw is 15 amps before it would trip it's internal breaker. This breaker automatically resets itself. Because of that there's no need to have any circuit protection on the circuit that powers this.
view full answer...
- What is the Amp Draw From the Fulton XLT 141401 Electric Trailer JackThe maximum amperage that the Fulton XLT jack # F141401 will draw is 15amps, so a 12v battery with at least 150 amp hour rating would be optimal to ensure that it's properly powered and also is not going to draw down too much with frequent use over the course of the day. You will want this to be a dedicated battery for the trailer.
view full answer... - Electrical Connection Options for a Powered Drive Trailer Jack It is recommend to power the Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs item # F141401 off of your trailer's battery. So to answer your question, yes it is ok to run both your trailer brakes and the jack off of your trailer battery.
view full answer... - Recommended Swivel Bolt-On Trailer Jack for Pop Up Camper I recommend taking a look at the Fulton F2 Swing-Up Jack # F1413230134 for your pop up trailer. This is a really nice, heavy-duty jack that features a static capacity of 2,000 pounds. It includes an articulating footplate that provides superior stability (even on unlevel ground), a swivel system for easy lifting and transport, and a maintenance-free construction with its lubricated, 1-piece gearbox. It has a lift height of 10 inches and will fit 4 inch and 5 inch trailer frames. The bolt-on...
view full answer... - Powered Trailer Jack Solution for Trailer with Low Tailgate ClearanceSince none of our powered A-frame jacks are going to be short enough for what you said you'd need you'd have to use a side mount trailer jack like the Fulton part # F141401 which has a lifting capacity of 2,500 lbs. I know you said you wanted at least a 3,000 lb capacity but I wanted to clarify that the lifting capacity of the jack is relative to the tongue weight of the trailer and not the overall weight of it which is easy to confuse.
view full answer... - Side Mounted Powered Trailer Jack Recommended for Horse TrailerMost of the powered trailer jacks we offer are designed to mount in the center of the a-frame which is inaccessible, as shown in the photo you provided (thanks for the photo, by the way!) The Fulton # F141401 would be the exception. The jack has a 2500 lb lift capacity which is plenty and will fit trailer A-frame members that are between 3 and 5 inches, so it would work perfectly for you. I've linked to an install/demonstration video for the powered trailer jack I recommended.
view full answer...
- Power Tongue Jack For Side Mount Connection On Straight Pole/A-Frame Trailer TongueI recommend the Fulton XLT Powered Drive Trailer Jack # F141401 for your trailer. This jack will fit 3" to 5" trailer tongues and bolts to the side of the tongue since you do not have an A-frame style connection. The jack has a lift capacity of 2,500lbs. It features 22" of total lift from the 8" drop leg and 14" of jack travel.
view full answer...
- Will The Dutton-Lainson StrongArm Electric Winch # DL25500 Operate With 6 Gauge Wiring? The Dutton-Lainson StrongArm Electric Winch # DL25500 uses gauge 8 wire so your current gauge 6 wire being thicker should be able to power your winch without an issue. Be sure to not use both the winch and the Jack # F141401 at the same time to reduce the risk of damaging the wiring. For using the winch with a boat trailer it is recommended to secure the boat onto the trailer with appropriate bow and transom tie down straps or chains. With the boat fully secured on the trailer, it is advisable...
view full answer... - Powered Side Mount Trailer Jack that Can Power From a 7-WayFor a powered trailer jack that attaches to the side of the trailer frame the Fulton XLT part # F141401 would work really well. Then to power it from a 7-way you'd just need to wire the jack to a 7-way plug like the Curt 7-Way part # C58145 which you could plug in as needed.
view full answer... - Electric Side Frame Mount Jack for Boat TrailerCongrats on your new boat and trailer and while there is an electric side frame mount jack, there is not a conversion kit that will allow you to turn the Bulldog Square Jack into a 12 volt jack. The best (and only) option to use an electric side frame mount jack is the Fulton XLT Powered Drive Trailer Jack - Drop Leg - Side Mount - 22" Lift - 2,500 lbs # F141401. This jack will simply bolt onto 3" to 5" trailer frames and wires to a 12 volt source like you were wanting. It is designed...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Edited by:
Lindsey S
Video Edited:
Jacob T
Installed by:
Cole B
Installed by:
Randy B
Installed by:
Andy C
Written by:
Shelly K
Updated by:
Alexander C
Updated by:
Hannah L
Updated by:
Mike S
Video by:
Zach D
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Quez
7/12/2023
Jack has worked flawlessly. Since it was installed it has been used no less than 9 times. Works great with & without boat on trailer.