See what our Experts say about this etrailer Trailer Bearings Races Seals Caps

• Pre-Greased Replacement 5-on-5 Hub for 3500-lb Dexter Axle
  You can confirm the weight rating of your Dexter axle by removing one hub and pulling its bearings. The included photo shows how part numbers usually appear on bearings. The specific bearings used will tell you the axle's weight rating. Just refer to the linked article that lists the bearings commonly used for various axle weight ratings. A new hub must use the same bearings as the original hub in order to fit on your spindles. A 3500-lb axle commonly uses bearings # L68149 and # L44649...
  view full answer...
  
• Can a Hub with Outer Bearing 15123 and LM67048 Both Fit Same Spindle
  The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part # AKHD-655-6-EZ-K would fit your axle.
  view full answer...
• Replacement Bearing Kit For Dexter 6,000 lb Axle 2266389
  Hey David, thanks for the picture. I was able to track down a spec sheet for your Dexter axle which I have included below. The 031-029-02 bearing is item # 15123 and the 031-030-02 bearing is item # 25580. For a bearing kit you can use part # BK3-110 which will come with both bearings, races, grease seal, spindle washer and cotter pin.
  view full answer...
• Recommended 5 Spoke Hub For M1102 Military Trailer
  The Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility # 8-174-5UC3 is the only hub that is compatible with those bearing inner diameters. This uses # 15123 which have the same inner diameter as the # 14125A, it simply uses a different race so it will be compatible.
  view full answer...
• Parts Needed to Convert Military Trailer M105A2 to Electric Brakes
  We've had this question before and we were able to determine that your M105A2 either uses a 5200 lb or 6000 lb axle so for hub drums you most likely will need the part # AKHD-655-6-K. This hub and drum comes with inner bearing part # 25580 and outer bearing part # 15123. It fits a 12 inch diameter brake assembly. You do want to check your existing bearings for their bearing numbers. There should be bearing numbers stamped on the side. If there is not numbers stamped on the side you can...
  view full answer...
  
• Replacement Hubs And Brake Assemblies For A 2006 Colorado 5th Wheel
  Hello David, I can definitely point you in the right direction. The Lippert 5,200 lb axles will use the standard 12" x 2" brake assemblies. For that I recommend the etrailer Rust-Resistant Electric Trailer Brakes # AKEBRK-7-D. This comes with a pair of Dacromet coasted electric brake assemblies. As far as the hubs, it is not quite so cut and dry. The 5,200 lb axles generally use a # 25580 inner bearing and a # 15123 outer bearing. Given that your axle is almost 20 years old, it may not...
  view full answer...
• Electric Over Hydraulic Disc Brake Conversion For Boat Trailer With Two Dexter 6K Axles
  Hello Dustin, thanks for reaching out. We actually carry conversion kits that are made specifically for this purpose. For your boat trailer with 6K Dexter axles, you can use the Hydrastar Electric Over Hydraulic Actuator Kit for Disc Brakes # HBA16-252-82 which will come with everything you need minus the disc brake kit itself. For a disc brake kit I recommend the DeeMaxx Disc Brakes # DE58YR. This kit comes with stainless calipers and the rotors use a rust-resistant Maxx coat which is...
  view full answer...
• Recommended Disc Brakes for a Dexter 4,400 lbs Axle
  Hey Randy, thanks for the information. Do your 2021 Keystone Passport wheels have a 5 on 4-1/2" lug nut pattern or a 6 on 5-1/2 lug nut pattern? You can add this information, along with any other questions you have, where it says Add Comment. The Dexter 4,400 lbs axles use the same hubs as 3,500 lbs axles, which have item # L68149 inner and item # L44649 outer bearings. The issue with the DeeMaxx Disc Brake Hubs item # DE89YR are you have to jump down to 3,500 lbs setups which only...
  view full answer...
• Looking For Replacement Brakes, Hubs, And Leaf Springs For My Dexter Axles
  Hey Steve, Thank you for that information you provided, it sets me up to get you the direct replacements. For that replacement brake assembly you will want to go with the Dexter Nev-R-Adjust Brakes # 23-458-459. This is the left and right hand assemblies that came originally on the trailer, ready to slide on and bolt on for you. We have the hub and drum assemblies as well that are pre greased with the bearings, races and seals already in them ready to slide on. For that you want to...
  view full answer...
• Replacement Bearing For Timken 15123 Trailer Hub Bearing
  We do offer the Replacement Trailer Hub Bearing, part # 15123 for your trailer but I was unable to find a cross-reference for the Timken 09067 bearing you stated you need. You can measure the inner diameter and see if there are any bearings from the attached pages that would work as a replacement for you. We also offer the matching race for the 15123 and that is part # 15245.
  view full answer...
• Recommended Disc Brake Assembly to Replace UFP Brakes on Boat Trailer
  Would you be able to tell me what you mean by alternatives or are you looking for the entire assembly?
  view full answer...
• Bearing And Seal Kit Needed For A Dexter D60 Axle
  Hey Brian, For inner bearing # 15123 you would need race # 15245 and for outer bearing # 25580 you would need race # 25520. The grease seal can be purchased with part # GS-2250DL. The Timken Bearing Kit # TMK42VR would include 15123/25580 Bearings, 15245/25520 Races, and 412920 Seal (2.25" ID/3.376" OD).
  view full answer...
• Can A Hub With A 15123 Bearing Be used To Replace A Hub That Used An LM67048 Bearing?
  Hi Aaron! The # 15123 bearing included with the TruRyde Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 12" - 6 on 5-1/2 - Pre-Greased # TRU38AV has the same 1.25" inner diameter as the # LM67048 bearing, so you can indeed use this hub. That said, make sure the inner bearing is either a # 25580 or has a 1.75" inner diameter and the seal is either a # GS-2250DL or has an inner diameter of 2.25" as well. These are what come with the # TRU38AV hub/drum. As long as all these...
  view full answer...
• Which Bearing And Seal Kit Is Needed For 2022 Cougar 368MBI Travel Trailer With Dexter 6K Axles?
  Hey there Mark! That's a great idea to stock up on some spare parts. Most people don't have the foresight like that. You will need either Bearing Kit, 15123/25580 Bearings, GS-2125DL Seal # BK3-110 or Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal # BK3-100 depending on if you have the 2.125" or 2.250" inner diameter seal. You likely have the 2.250" I.D. seal but you'd need to check the part number or measure the seal to verify, unfortunately. The only difference in the kits is the grease...
  view full answer...
• Timbren Axle-Less Suspension System Compatible with Jeep for Matching Trailer
  For the Timbren Axle-Less kit compatible with the bolt pattern of 5 on 5 like a Jeep, you would need the 2,200 lb capacity # ASR1THDS03. The spindles on the Timbren system are a little larger than their thru-axle counterparts, so the 3,500 lbs # ASR3500S06 will only fit larger hubs that won't have the bolt pattern you seek. Using # ASR1THDS03, you can then use the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 5 # AKIHUB-550-35-EZ-K or the Trailer Hub and Drum Assembly...
  view full answer...
• Replacement Hubs With 5 on 5 Bolt Pattern
  We do have hubs available with a 5 on 5 bolt pattern; they are each compatible with 3,500 lb axles, have inner bearing # L68149 and outer bearing # L44649 and fit wheels that are between 13 inches and 15 inches. You need to take apart your old hub in order to find out if you have the same bearing numbers. If so hub and drum assembly # AKHD-550-35-K will work; for an idler hub assembly # AKIHUB-550-35-K would be the right choice. I've added a link to video reviews of these parts for you...
  view full answer...
• Do You Have a 6,000 lbs Axle w/ a 89" Hub Face?
  Hey Val. Our Trailer Axle Beam with Easy Grease Spindles item # e23GR is going to be the best option for a 6,000 lbs capacity axle that's 89" long. We don't have any axles with a 68.5" spring seat so you'll need to have a welder install two of the Spring Seats item # TRSS300 per axle to attach the axle to your suspension. The spindles fit item # 25580 inner and item # 15123 outer bearings. You'll also need a set of the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles...
  view full answer...
• What Is The Difference Between Dexter Hub/Drum 8-201-5UC3-EZ And 8-201-9UC3-EZ
  Hi Jim! The Dexter Trailer Hub and Drum Assembly # 8-201-5UC3-EZ and # 8-201-9UC3-EZ are very similar, but there are a couple differences. You noted the weight capacity differences, and that is due to the bearing combination, which I have listed below: # 8-201-5UC3-EZ Inner bearing # 25580 (1.75" inner diameter) Outer bearing # LM67048 (1.25" inner diameter) Inner race # 25520 Outer race # LM67010 # 8-201-9UC3-EZ Inner bearing # 25580 (1.75" inner diameter) Outer bearing # 15123 (1.25"...
  view full answer...
• Replacement Trailer Brake Assemblies For a 2011 Forest River Sierra 5TH Wheel Camper
  I recommend the Dexter Nev-R-Adjust Electric Trailer Brake Kit # 23-458-459 for your 2011 Forest River Sierra 300RL. These will only require you to adjust the brakes to ensure they are set correctly when you install them. After that they will self adjust themselves as the brake material wears away. This will ensure your brakes last longer and will keep you out from under the trailer adjusting the brakes. The Trailer Hub and Drum Assembly # AKHD-655-6-EZ-K will provide you with a new hub/drum...
  view full answer...
• Looking for Replacement Bearing Kit for Hub with Bearings 15123/25580
  Hey Mark, when in doubt the correct bearing info is what is listed on the bearings that are in your hub. So if you have a # 25580 and a # 15123 that is for sure the bearings you will need as a replacement. We have these bearings in a kit with the correct size seal with the part # BK3-110.
  view full answer...
• Looking for Replacement Bearings for etrailer 5,200 lb Axle e75SR
  Hey Lane, since your axle part # e75SR uses the bearings # 25580 and # 15123 with the grease seal # GS2250DL the correct bearing kit would be the part # DBRKHW6. How many miles have you put on the axle?
  view full answer...
• Determining Capacity of an Old Trailer Axle with No Information on the Axle
  The 15123 bearing is still common but I could not find any information on the 09057 bearing. But given that your hubs have the 4 bolt pattern it is likely that the axle is rated under 3,000 pounds. Most likely it is a 2,000 pound axle. Measure the spindle where the 09057 bearing rides using calipers such as # PTW80157 I can see if there is a different bearing with the same inner diameter that is commonly used with 15123 and go from there. Since you still have the trailer frame as well...
  view full answer...
• Recommended Brake Hubs, Assemblies, and Breakaway Kit for a Trailer w/ 6,000 lbs Axles
  Hey Chuck, I sure can and thanks for the information! For replacement hubs, you'll need the Easy Grease Trailer Hub and Drum Assembly item # AKHD-655-6-EZ-K if you have EZ lube axles or item # AKHD-655-6-K if you have standard axles without a grease zerk behind the dust cap. They are sold individually. These hubs fit spindles with inner bearing item # 25580 and outer bearing item # 15123. It wouldn't hurt to confirm the part numbers off of the bearings in your current hubs. 6,000 lbs axles...
  view full answer...
• Hub and Drum Assembly for AL-KO T-52 Axle
  Based on my research, your AL-KO T-52 Axle has # 42 spindles that use hub assemblies with a # 25580 inner bearing and # 15123 outer bearing. You will just want to determine the bolt pattern you are needing as well as the axle capacity, as this can vary between different models. I have attached an article that will help you determine the bolt pattern on your existing hubs. The etrailer.com Trailer Hub and Drum Assembly # AKHD-655-6-K will work for 5,200 pound and 6,000 pound axles and...
  view full answer...