Timbren Axle-Less Suspension System Compatible with Jeep for Matching Trailer
Published 05/08/2019
Products Featured in This Question
Question:
Just to verify, this axle ASR35HDS05 will work with Kodiak Trailer Hub for 5,200-lb to 6,000-lb Axles - 6 on 5-1/2 - Stainless Steel Item # KH42655S
asked by: Eric B
Expert Reply:
For the Timbren Axle-Less kit compatible with the bolt pattern of 5 on 5 like a Jeep, you would need the 2,200 lb capacity # ASR1THDS03. The spindles on the Timbren system are a little larger than their thru-axle counterparts, so the 3,500 lbs # ASR3500S06 will only fit larger hubs that won't have the bolt pattern you seek.
Using # ASR1THDS03, you can then use the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 5 # AKIHUB-550-35-EZ-K or the Trailer Hub and Drum Assembly # AKHD-550-35-EZ-K.
If you have the 5-on-5.5 inch like you stated, then you would need hubs # AKIHUB-555-35-EZ-K or hub/drum # AKHD-555-35-EZ-K. I've attached an article to help you measure your bolt pattern to confirm which you have.
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Standard Duty - 4" Lift - 4 Bolt Flange - 3,500 lbs
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- No Hubs
- 3500 lbs
- Spindles Only
- Universal Fit
- Lift - 4 Inch
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Timbren Axle-Less System with 5 on 5 Bolt Pattern Hubs for Overland Trailer
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 5 - Pre-Greased
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - 4" Lift - 4 Bolt Flange - 3,500 lbs
- Q&A: Recommended Timbren Axle-Less System for a Livin' Light QuickSilver 10.0 Pop-Up Camper
- Search Results: timbren axle~less trailer suspension
- Video: Let’s Check Out the TorkLift Cannon Hitch Extension
- Q&A: Adding Trailer Brakes to Livin Lite Quicksilver 10.0 Trailer and 2011 Subaru Forester with 4-Way
- Q&A: Recommended 2200lb Axle That Uses 3500lb Hubs and Bearings
- Search Results: wheel
- Shop: Loadstar ST215/75D14 Bias Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: TorkLift Cannon Hitch Extension - 3" Ford Super Duty Factory Hitch - 42" Long
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Video: Review of Timbren Trailer Axles - Axle-Less Trailer Suspension - T43AV
- Search Results: trailer wiring
- Search Results: electric jack camper jacks
- Search Results: camper jacks
- Q&A: Why Do Hitch Extenders Reduce Hitch Capacity but Long Ball Mounts Do Not
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer tires and wheels
- Video: How to Choose a Trailer Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Article: How to Measure for Trailer Hitch Drop
- Video: Measuring To Choose The Right Trailer Axle
on Trailer Axles
Eric
4/30/2019
After taking measurements of my military M1101 trailer, I think this axle would work very well but one with a 2 inch lift would work better. Is there such a beast?