Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs

Ask the Experts about this etrailer Camper Jacks

• Installation of etrailer Landing Gear
  The Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs # RVLG-8HDL will simply mount to the weld-on brackets by being bolted on. While an online copy of the manual is not available for this specific landing gear, I did cut out a portion of the Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs # LG-183708 so you can take a look. In regards to the brackets you asked about, the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket # LC113511 will work with...
  view full answer...
• Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
  I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or...
  view full answer...
• What is the Difference Between etrailer 8,000 lb Landing Gear Sets
  You are right on the money with the differences between the two etrailer landing gear sets; the only difference is that one comes with the manual hand crank (handle) and the other does not: - Manual Hand Crank: Landing Gear Set with Handle - 36-1/2" Lift - 8,000 lbs # RVLG-8HDL - Without Manual Hand Crank: Landing Gear Set - 36-1/2" Lift - 8,000 lbs # RVLG-8000 Both will have a 1-year warranty as they are the same part. I have added a link to a video review for you to check out as well.
  view full answer...
• Replacement Landing Gear Set for Forest River Cardinal Fifth Wheel
  I have some really great options for complete landing gear sets to use on a Forest River Cardinal Fifth Wheel, the Landing Gear Set with Handle part # RVLG-8HDL for example is super cost effective and it comes with everything you need. In regards to fit, it should work but I do recommend checking that the weld stops on your existing landing gear legs are 15-1/2' apart inside to inside.
  view full answer...
• Outside Leg Dimensions of etrailer.com Landing Gear for 1995 Skyline Layton Fifth Wheel
  The Landing Gear Set w/ Handle - 20-1/2" Travel - 8,000 lbs # RVLG-8HDL has an outer tube width of 2-1/2 inches. As long as the weld stop locations shown in the attached photo work, you will have no issues making this a direct replacement and reusing your current brackets.
  view full answer...
• Replacement Landing Gear Recommendation for a 2011 Keystone Raptor 3812 Toy Hauler
  While I don't know exactly what landing gear you have on your 2011 Keystone Raptor 3812 Toy Hauler, I can say that you should be able to replace them with the Landing Gear Set w/ Handle # RVLG-8HDL as this landing gear uses the standard weld mount locations of 15-1/2" inside and 17-1/2" outside measurements (see attached). You can confirm fitment by measuring where the weld stops are on your current landing gear. This set comes with a handle but if you don't already have an electric...
  view full answer...
• Difference Between etrailer Landing Gear Jacks RVLG-8HDL and RVLG-8000
  The difference is that the # RVLG-8000 does not come with a handle and the # RVLG-8HDL does come with one. Aside from that it's the exact same jacks. We don't offer replacement legs for them so if you need new legs best toption is the # RVLG-8HDL which will give you a new gear box as well.
  view full answer...
• Picking Out Replacement Landing Gear for 2010 Keystone Xlite
  If the landing gear on your 2010 Keystone Xlite is Ram jack brand landing gear then yes the # RVLG-8HDL would fit and your current motor part # M1230 would work as well. If you instead have the brand LCI, Lippert, Venture, or Stromberg you'd need the # LG-183708 instead. This is the much more common set that I believe you most likely have.
  view full answer...
• Will The Lippert Motor 142178 Work With the Landing Gear Set RVLG-8HDL
  Yes, the Lippert Motor for Electric Landing Gear part # LC142178 that you said you have will work with the Landing Gear Set part # RVLG-8HDL. The switch you have now can then be reused or we have the Lippert Components 5th Wheel RV Landing Gear Switch part # LC145236.
  view full answer...
• Replacement Landing Gear for 2009 Heartland Sundance 5th Wheel Trailer
  The 8K Landing Gear Set w/ Handle # RVLG-8HDL should fit just fine as it uses the standard weld stop locations measuring 15-1/2" or 17-1/2" for the mounting brackets. I don't know what the current bracket dimensions are for your 2009 Heartland Sundance but you can quickly verify if this is compatible by measuring the space between your mounting brackets. If it is 15-1/2" or 17-1/2" then you are good to go! This landing gear comes with a manual hand crank and you have the option to add...
  view full answer...
• Landing Gear Set to Replace Atwood Set on 1998 Excel Peterson with Atwood Landing Gear
  The landing gear part # RVLG-8HDL would bolt right up to your RV that had Atwood landing gear but since you just bought a Stromberg Carlson motor your best option would be to go with the Lippert manual landing gear set part # LC333966 instead as this also bolts right up to your RV but will allow you to also use the motor you have. The motor you have is not compatible with the # RVLG-8HDL.
  view full answer...
• How to Determine Replacement Landing Gear for 2007 Weekend Warrior LE3305
  To find the correct landing gear for your 2007 Weekend Warrior LE3305 you'll only need to know the distance between the weld stops that your current landing gear is attached to. From there you can choose the lift and weight capacity of your landing gear and if you want a manual or electric motor. Standard measurements for weld stops are 15-1/2 inches from inside to inside and 17-1/2 inches from outside to outside. Those dimensions are the same used on top sellers such as the Landing...
  view full answer...
• Can the Follow-Leg Be Replaced On an Atwood Landing Gear Set
  I would love to be able to give you a replacement follow leg for your landing gear set but sadly it's not going to be that simple. The issue is that Atwood has gone out of business and the products they offered while in business did not always follow the industry standard so I would really have no way of making sure you get a compatible follow-leg that's to say there is even one available which is really anyone's guess. I hate to say it but the solution for you and all of our many other...
  view full answer...
• Replacement Landing Gear for 2010 Keystone Fuzion FZ322 Fifth Wheel Trailer
  There is a way for you to determine the correct replacement landing gear for your 2010 Keystone Fuzion, though we do not have landing gear made specifically for your trailer. Instead, you will need to measure the mounting brackets on your trailer from outside to outside like in the attached diagram and choose the amount of lift and weight capacity that will work for you. For example, you may be able to use the Landing Gear # RVLG-8HDL, which has an 8,000 lb capacity, offers 20-1/2" of...
  view full answer...
• Recommended Replacement Landing Gear Set for a 2004 Keystone Cougar 5th Wheel Trailer
  When you are looking for replacement landing gear the 2 big things to take into consideration are the weight of your trailer and the weld stop locations on your current setup. Since the GVWR of your 2004 Cougar is 10,300 lbs our Landing Gear Set w/ Handle # RVLG-8HDL that you referenced can handle the weight capacity of your RV. Keep in mind that some of the weight of your trailer is still supported by the axles and tires so a landing gear setup doesn't need to be rated for the total...
  view full answer...
• Would etrailer.com Landing Gear Set # RVLG-8HDL Fit 1996 Excel 5th Wheel Camper
  The Landing Gear Set w/ Handle # RVLG-8HDL that you referenced is MOST LIKELY the correct set of landing gear for your 1996 Excel 5th wheel camper as this landing gear fit is the most common seen on RVs. I would actually be shocked if it didn't fit because of that. So what you'll need to do to verify is measure the dimensions of the welded mounting brackets on your camper and compare them to the picture I attached. The sure way to tell is that if the distance between the mounting brackets...
  view full answer...
• Replacement Landing Gear Leg Set for a 2005 Keystone Montana 3670RL
  Yes, the Landing Gear Set w/ Handle part # RVLG-8HDL will fit your 2005 Keystone Montana 3670RL. The weld stops are 15-1/2" apart from the bottom of upper weld stop to top of lower weld stop and 17-1/2" apart from the top of upper weld stop to bottom of lower weld stop. According to my research, this should be the same as what is on your trailer now so they will be a direct replacement. If you would like to add an electric motor to this set then you can using part # LC142178.
  view full answer...
• Difference Between Landing Gear Sets
  The only difference between the two landing gear sets you referenced is that Landing Gear # RVLG-8HDL comes with a handle and # RVLG-8000 does not. Apart from that they are the exact same landing gear sets, with 20-1/2" of travel, an 8,000 lb weight capacity, 44-1/2" between the legs when they are as close as possible and 72" when as far apart as possible. This landing gear is designed to fit the standard weld stop measurements of 15-1/2" inside to inside of weld stops and 17-1/2"...
  view full answer...
• Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
  Good news! I was able to go out to the warehouse and measure the etrailer landing gear # RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld stops is 15-1/2 inches. I have linked a dimensional diagram to this page for you to better see where I measured. I have linked this product to this page for your convenience.
  view full answer...
• Can Trailer Landing Gear Legs be Welded Directly to Frame
  Trailer landing gear sets like the etrailer.com # RVLG-8HDL that you referenced are designed to bolt onto brackets that are welded to the frame. In terms of function or capacity there is no particular reason you couldn't just weld the legs directly to the frame instead but I don't recommend doing this for a couple of reasons. First the actual install process is going to be a lot more in depth than just bolting to existing brackets or even welding on new ones for the legs. You will need...
  view full answer...
• Replacement Landing Gear Needed for Part # VMC900R-304103
  If you are looking to replace your landing gear then I have a possible solution for you, we just don't carry any sets with the part VMC900R-304103 that you referenced. Our Landing Gear Set # RVLG-8HDL is rated for 8,000 lbs and has 20-1/2" of travel. This set comes with a manual hand crank, but if you are wanting for your landing gear to be electric then you need the 12V DC Motor # LC142178 as well. To determine if this landing gear set is compatible with your 2008 5th wheel you simply...
  view full answer...
• Recommended Replacement Landing Gear For 1988 Fleetwood Cimarron Model 32
  Without knowing the brands of landing gear on the 1988 Fleetwood Cimarron Model 32 its not possible to find the replacement gears. Since the landing gear is most likely older, the best option is to just replace it. I recommend to measure the distance between the mounting brackets on the 5th wheel. The most common measurement is 17-1/2". If that is the the measurement between your mounting brackets, I recommend the Landing Gear Set w/ Handle part # RVLG-8HDL which gives you 36-1/2" Lift...
  view full answer...
• Difference Between etrailer.com 5th Wheel Trailer Landing Gear Kits RVLG-8000 and RVLG-8HDL
  The only difference between the two part numbers is that the # RVLG-8000 does not include the manual crank handle and the part # RVLG-8HDL does include it. Aside from that it's the exact same landing gear set.
  view full answer...
• Powered Jack Recommendation to Replace 3,500 Power Jack that Strains
  For your style of A-frame trailer and it's loaded weight the best option is a higher capacity powered a-frame jack like the Husky Brute Jack part # HT87247 which has a 4,500 lb lifting capacity which would be more than needed since your trailer that weighs right at 10k would have a tongue weight around 1,000 lbs. My favorite powered jack to recommend is the Husky Jack part # HT87247 as it has bearings in the screw which allow it to operate quicker and smoother. It also shuts off automatically...
  view full answer...
• How to Know if Landing Gear Set # RVLG-8HDL Will Fit 2001 Sunnybrook 31BWFS
  In order to pick out a direct replacement for the landing gear on your 2001 sunnybrook 31bwfs we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Tandem Landing Gear Set # RVLG-8HDL. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of...
  view full answer...
• Replacement for Atwood Landing Gear on 2004 Fleetwood Wilderness 5th Wheel Trailer
  I reached out to my contact at Lippert who said that the Atwood line has been discontinued and they don't have any replacement parts for it. Since this is the case you'll need to replace your Atwood jack. Was this for the landing gear or for a stabilizer jack? If you can let me know this I can recommend a replacement for you.
  view full answer...
• Replacement Landing Gear for 2005 Americamp 5th Wheel
  Since your 5th wheel already has landing gear mounting clamps in place you'll just want to check the spacing of the clamps to confirm the fit of Landing Gear Set # RVLG-8HDL. This 8K landing gear set has weld stops (that mate with the clamps) and these are spaced apart by 15-1/2-inches on their inside edges and by 17-1/2-inches on their outside edges. This is shown in the linked photo. The spacing between the two legs is adjustable and can range from 44-1/2-inches to 72-inches. If you...
  view full answer...