Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear
(31 reviews)
Price: $23.26
In Stock
Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear
Item # RVLG-HDL
Retail:$25.73
Our Price: $23.26
You Save: 10%
Orders above $50 qualify for Free Shipping
In Stock
- All Info
- Reviews (31)
- Q & A (0)
- Videos (2)
- Photos
- Why etrailer?
etrailer Accessories and Parts - RVLG-HDL
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- etrailer
Replace the crank from your etrailer or Ram landing gear set (RVLG-8HDL). In case of power or mechanical failure, this crank handle will let you manually retract or extend the fifth-wheel landing gear legs.
Features:
- Replaces the crank handle from your etrailer or Ram 5th-wheel landing gear set (RVLG-8HDL)
- Durable steel construction with corrosion-resistant zinc-plated finish
- Handle radius: 8-1/2"
RVLG-HDL Replacement Manual Crank Handle for Ram 5th Wheel Landing Gear
Video of Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for etrailer and Ram 5th Wheel Landing Gear Replacement Crank Handle Review
John: Hey guys, John here from etrailer.com. Today we're going to take a look at the Replacement Hand Crank for the etrailer.com Landing Gear Set. As I said, it's a replacement hand crank here, so you're going to fit it on the end of your landing gear. This is going to be used for if you don't have the electric gear motor here, or maybe you're at the campsite and you've lost power. This still allows you to operate your landing gear and raise and lower it.It's going to feature a nice long handle, which helps give us some more torque. This landing gear is rated for 8,000 pounds, so depending on your trailer it might be a little more difficult to raise and lower the legs.
As you can see, the grips here, they spin freely, which allows for easier operation of the landing gear. It has a nice clear zinc coated finish which helps prevent rust and corrosion.One thing I would like to point out, a common question I've gotten from customers is whether they can use this with other landing gear sets. It kind of depends. There is no standard dimensions for this fitting, and so your best bet is to just get the exact replacement for your landing gear set. That'll complete our look at the Replacement Handle here for the etrailer.com Landing Gear.
Thanks for watching.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear - RVLG-HDL
Average Customer Rating: 4.7 out of 5 stars (31 Customer Reviews)
Replace the crank from your etrailer or Ram landing gear set (RVLG-8HDL). In case of power or mechanical failure, this crank handle will let you manually retract or extend the fifth-wheel landing gear legs.by: Lance05/25/2022
Arrived timely and works as expected. Simple transaction
Thank you
by: Steve05/24/2022
Very quick shipment and packed very well. Will use again
by: CallMeColt07/06/2019
Great value! I actually got this to use with a military trailer that was missing the handle to crank the jack up & down. Much cheaper than finding the surplus part.
by: Dean M Jensen 10/04/2017
Recieved the product and have installed half of it,got the unit in today looks good ,works well.
by: David10/10/2017
I purchased this handle along with new landing gear, but it didn't actually work. My camper has a smaller guide tube that this handle won't fit inside. The old handle worked fine, my mistake. The new handle is also longer. It is good quality and nicer than my old one. I am happy with the purchase, and I can use it on something else, but I didn't need to buy it.
by: Larry 09/21/2018
Product is as described and is of good quality. I bought it as a (replacement) backup for the electrically operated legs on my fifth wheel.
by: Robert 01/11/2022
Good quality product.
by: Dennis 11/13/2021
Order get here in good time and its what I order.
by: Shayne08/11/2019
Great product. Took less than an hour to replace the old landing gear with the etrailer brand. Was a direct replacement with no problems. Shipping was fast.
by: Lane 03/30/2020
Works very well for my application (military trailer).
by: Mike06/06/2019
Pretty easy install and lifts my heavy toyhauler easier
by: Martin 06/19/2021
This crank is larger and more sturdy than the one that came with my RV from the manufacturer.
by: Bob 05/11/2021
Well build and fit perfect
by: Brenda 02/26/2021
Works great!
by: Leah 09/11/2020
It came faster than I thought it would. Haven't tried it yet. But from what I have learned it is exactly what we need to open up our pop outs. Thank you for such fast delivery.
by: Phil k10/13/2017
As advertised came quick, easy order ,
Good price free shipping ??
by: Joel10/07/2022
by: Alex 12/19/2019
Great tool.
by: Everett W06/18/2017
Better than expected quality with prompt delivery
by: Donnie04/07/2017
Great tool perfect
by: Edgar 09/18/2021
by: cgw98x 05/03/2017
nice
by: Brian 05/05/2021
by: Brian 08/12/2022
by: Donald08/05/2022
25
31
Show More Reviews
See what our Experts say about this etrailer Accessories and Parts
- Replacement Crank Handle for Ram 5th Wheel Landing Gear Compatibility With 2007 Fleetwood Nitrous TTI don't have any way of determining if the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL will work with your 2007 Fleetwood Nitrous Hyperlite TT Toy Hauler or not, unfortunately. The Replacement Crank Handle # RVLG-HDL is designed to be a replacement for Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-8HDL. The part where # RVLG-HDL connects to the landing gear is 1/2" while the outer sleeve has a diameter of 3/4". I recommend...
view full answer... - What is the Outer Diameter of the Slotted End of Crank Handle RVLG-HDLAccording to my calculations the outer diameter of crank handle # RVLG-HDL is a hair more than 3/4 inches. Its actually closer to 13/16 inches.
view full answer... - DIameter of Replacement Crank Handle for Landing GearThe inside diameter of the end of the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL is 1/2 inch, and the outside diameter is 13/16 inches.
view full answer...
- What Is The Overall Length Of The Replacement Crank Handle For Etrailer 5th Wheel Landing Gear?The Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL measures 31" long, including the handle on the end. The crank assembly itself measures 27" not including the handle on the end. I attached a photo diagram along with a demonstration video for you.
view full answer...
- What Is The Shaft Of The Replacement Crank Handle For Etrailer 5th Wheel Landing Gear RVLG-HDLThe diameter of the shaft of the Replacement Crank Handle # RVLG-HDL that you referenced is 1/2 inch.
view full answer... - Diameter of Crank Handle for 8,000 Pound etrailer.com Landing Gear SetThe Crank Handle # RVLG-HDL has an inner diameter of about a 1/2 inch on the slotted end. It's designed to be used with Landing Gear Set # RVLG-8000.
view full answer...
- Compatibility of Landing Gear # RVLG-800 with 2011 Heartland Big Country 3450ts TrailerThe etrailer.com Landing Gear Set - 20-1/2" Travel - 8,000 lbs # RVLG-8000 will fit your 2011 Heartland Big Country as long as the legs are a minimum of 44-1/2 inches in between and a maximum of 72 inches apart. The weld stops measure 15-1/2 inches inside to inside and 17-1/2 inches outside to outside. I've attached a picture to assist. The hand crank is available as a separate item and is part # RVLG-HDL.
view full answer...
- Can the Gear Box on the Landing Gear Set RVLG-8000 Be TurnedThe gearbox on the Landing Gear Set part # RVLG-8000 can be rotated 90 degrees so that the drive shaft is positioned in front of the leg. That said, you will need to make sure you have adequate clearance to make a full rotation on the handle. The actual handle is not included either so if you don't have one you will also need the Replacement Crank Handle part # RVLG-HDL.
view full answer... - Inside and Outside Diameter of Slotted End on Replacement Crank Handle RVLG-HDLThe inside diameter of the portion of the handle that fits into the jack, is approximately 1/2 inches, while the outiside diameter is closer to 13/16 inches. The etrailer Crank Handle # RVLG-HDL is designed to be used with Landing Gear Set # RVLG-8000.
view full answer...
- How to Determine Fit of Landing Gear RVLG-8000 on 2007 Dutchman ColoradoI can tell you how to determine if the Landing Gear Set # RVLG-8000 will fit your 2007 Dutchman Colorado 5th wheel, though landing gear is a universal type of fit, and there isn't landing gear that is a specified fit. It's pretty easy to determine though, as all you will need to do is measure the distance between the mounting brackets on your Colorado as shown in the diagram. So long as that measurement is 17-1/2 inches from the top of the upper weld stop to the bottom of lower weld stop,...
view full answer...
- Compatibility of Replacement Crank HandleThe Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL is designed to be a replacement handle for Landing Gear Set # RVLG-8HDL. Replacement handles attach to landing gear in a number of ways so they need to be matched with their manufacturer. For example, # LC119226 is a replacement manual crank for Lippert Components landing gear. Once you take a look at the manufacturer of your landing gear, just go to the link I've attached which has each of our available...
view full answer... - Can etrailer Landing Gear Replace Landing Gear On 2007 Montana Fifth Wheel TrailerThe etrailer Landing Gear Set, part # RVLG-8000 can be used to replace the landing gear set you have on your 2007 Montana. The hand crank is available as a separate item and is part # RVLG-HDL. Most landing gears are interchangeable but you can take a quick measurement to make sure this works for you. The weld stops measure 15-1/2 inches inside to inside and 17-1/2 inches outside to outside. For a landing gear with a manual crank included you can order part # RVLG-8HDL. You can add...
view full answer...
- What Is The Difference Between The Landing Gear Set RVLG-8000 & RVLG-8HDL?The only difference between the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-8HDL that you mentioned, and the Landing Gear Set # RVLG-8000 is that # RVLG-8HDL comes with the handle, whereas if you were to go with # RVLG-8000 you'd need to purchase the handle separate with # RVLG-HDL. Both of these systems are rated for the same 8,000lbs capacity limit, and have 36-1/2" of total lift. Additionally, both of these can also be upgraded from manual to electric...
view full answer... - Will etrailer Landing Gear Fit a 2013 Columbus 320 RS 5th Wheel TrailerYou can use the etrailer landing gear set # RVLG-8000 on your 5th wheel trailer. As it comes it is a manual set and you will need crank handle # RVLG-HDL. You can also add a motor to the system using # LC142178.
view full answer... - Replacement Landing Gear Needed for a 2006 Big Horn with Part VMC900L-181526 Landing GearAlthough I don't know exactly what landing gear you have on your 2006 Big Horn, I can help you find some replacement landing gear. The part VMC900L-181526 that you referenced looks to be some Venture landing gear from the first digits "VMC900L". If you check the weld stops on your landing gear they should measure 15-1/2" on the inside and 17-1/2" on the outside (see attached picture). If this is the case then you can use the Landing Gear Set # RVLG-8000 which has 20-1/2" of travel and...
view full answer...
- Troubleshooting Atwood Landing Gear Leg That Doesnt MoveIt sounds like the screw itself is damaged if the motor and gears are turning but the leg isn't moving. Atwood no longer is in the 5th wheel landing gear business so I recommend replacing your landing gear completely. The reason you would need to change out your whole set is because both legs need to move at the same ratio so that your trailer raises and lowers evenly on both sides. Since replacement parts are already becoming scarce for Atwood landing gear it would be better in the long...
view full answer...
- Recommended Landing Gear For 2015 Forest River Wildwood Heritage Glen TrailerThe etrailer.com Landing Gear Set - 20-1/2" Travel - 8,000 lbs # RVLG-8000 will work well for your 2015 Forest River Wildwood Heritage Glen. The legs have a combined weight capacity of 8,000 lbs and retract to a height of 32-3/4 inches. The distance between legs can be anywhere between 44-1/2 inches and 72 inches. It has a gear ratio of 3 to 1. The manual crank for this is Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL. You may also choose to add the...
view full answer... - Atwood Landing Gear Replacement for 36 Long Landing GearTo replace the Atwood landing gear on your 5th wheel trailer you will need to measure the distance between your weld stops. This is typically 15-1/2" on the inside and 17-1/2" on the outside (see attached photo). We do have replacement options but since Atwood is no longer in the landing gear business you need to replace your whole landing gear set to ensure that the gear ratio and strengths are the same. If your weld stop locations match the picture then I recommend using the 8,000 lb...
view full answer...
- Replacement 8,000 lb 5th Wheel Landing Gear Set for 5th Wheel Toy HaulerThe Landing Gear Set part # RVLG-8000 is rated for 8,000 lbs like what you believe your current landing gear's weight capacity is. It also has a leg height of 32-3/4 inches to 53-1/4 inches giving you a travel of 20-1/4 inches which will work well for your application. This jack can be operated manually using part # RVLG-HDL or with a 12V DC motor using part # LC142178. The weld stops on this landing gear set have distance of 15-1/2 between the bottom of the upper weld stop and the top...
view full answer...
- How To Install the Landing Gear Set Part # RVLG-8000The installation of the Landing Gear Set part # RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part # LC113511 to it, 15-1/2" apart. Once these are installed you can then mount the jack tube and modify a cross-shaft that connects the two together which is included. Then, you will need to obtain a handle, the Crank Handle part # RVLG-HDL to raise and lower the legs. Unfortunately, we do not have a video...
view full answer...
- Depth of Slot on RVLG-HDL and LC119226 Replacement 5th Wheel Landing Gear Crank HandlesOn the Lippert # LC119226, the slot in question is 1/4 inch wide by 3/8 of an inch deep, on the # RVLG-HDL it measure 1/4 inch wide by 7/16 of an inch deep. You can see these photos in the photo I've provided.
view full answer...
- Replacement Landing Gear Motor and Gear Box Needed for a 2004 Keystone Montana 2980I do have a solution for you, but unfortunately manufacturers don't keep that kind of information on file. You could try using a replacement gearbox like part # RVLG-RDBOX and the compatible motor # LC142178 that fits Ram jacks, but without knowing the manufacturer and part number it would just be a guess as to whether it is the correct part or not. What I recommend doing is going ahead and just replacing your whole landing gear setup. It might be getting close to time to do that anyways...
view full answer...
- Will etrailer Landing Gear RVLG-8000 Fit a 1994 Terry 5th Wheel TrailerLanding gear set # RVLG-8000 will likely fit your 1994 Terry 5th wheel trailer. The size of the jack tubes are standard for 5th wheel jacks and the stop in the legs for the frame clamps have a standard spacing. I have included a picture showing the stop measurements on the legs so you can compare that to your existing set. If that and the other measurements match up then this kit is a great option. The hand crank is available as a separate item and is part # RVLG-HDL. Or you can add a...
view full answer...
- Will etrailer Landing Gear RVLG-8000 Fit a 1994 Avion/Fleetwood 5th Wheel TrailerMost likely yes, etrailer Landing Gear Set # RVLG-8000 will fit your 1994 Avion Fleetwood 5th wheel trailer. You will want to measure the distance between the bracket stops on the sides of the outer tubes of your existing landing gear to make sure it is a match. I have included a picture showing these measurements. The 15-1/2 inches is the distance between the upper and lower stops. The 17-1/2 measure is the distance from the top of the upper stop to the bottom of the lower stop. I have...
view full answer...
Do you have a question about this Accessories and Part?
Why etrailer.com?
At etrailer.com we guarantee:Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate accessories and part information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Installed by:
Jeff D
Installed by:
Randy B
Video Edited:
Joshua S
Updated by:
Wilson B
Updated by:
Mike S
Written by:
Amanda M
Video by:
Jonathan Y
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-636-306-4830
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.