Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K

Ask the Experts about this etrailer Accessories and Parts
Do you have a question about this Accessories and Part?

• Replacement Parts for Ram 12000 Series Jacks
  
• The rod and nut for the 12,000 Series Ram jacks is # TJD-12000-RODNUT and the replacement bearing is # TJD-12000-BR.
  view full answer...


• Repair Kit for Ram Series 12000 Trailer Jack
  
• To repair a Ram Series 12000 jack, like # TJD-12000SP-R2, we have the Gear Kit # TJD-12000-GR or the Replacement Rod and Nut # TJD-12000-RODNUT. Or you could need both. I just depends on what the problem is exactly.
  view full answer...


• Ram Square Jack Replacement Screw Assembly
  
• We have several replacement parts for the internals of a Ram brand square jack. The Replacement Rod and Nut # TJD-12000-RODNUT will fit the following Ram jacks: # TJD-12000SP-F2 10K Sidewind with 12-3/8 inches of travel w/handle # TJD-12000SP-R2NH 10K Sidewind with 12-1/4 inches of travel w/o handle # TJD-12000SP-R2 10K Sidewind with 12-1/4 inches of travel w/handle Some other replacement parts for these Series jacks are: # TJD-12000-GR Replacement Gear Kit # TJD-12000-BR Replacement...
  view full answer...


• Gear Kits for Single Speed Ram or etrailer Jack
  
• It is not possible for me to tell you with any degree of certainty that you can retrofit the Replacement Gearbox for etrailer and Ram 2-Speed Square Jacks # TJD2SP-12900-GBX for use with a single speed Ram jack though there are replacement gears available. If you have the TJD-12000 Series jacks such as # TJD-12000SP-R2 there is the Replacement Sidewind Gear Kit # TJD-12000-GR as well as Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT which you...
  view full answer...


• Replacement Screw and Nut Kit for Jacks
  
• There is one screw and nut kit longer than the 17-3/4" of the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT, which is the 20-3/16" Replacement Screw and Nut Assembly for Bulldog Square Jacks # BD500250. These parts are designed for specific jacks so please be aware if you needed a replacement for a TJD-12000 Series jack that Replacement # BD500250 would not work; this replacement screw and nut fits Bulldog Jacks rated for 10,000 lbs of lift...
  view full answer...


• Threaded Rod, Gears, and Pins for Ram Square Sidewind Jack
  
• For your Ram 10,000 lb jack, it sounds like you will need to rebuild it as the amount of force used most likely damaged the gears and the threaded rod. I recommend the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT along with the Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs # TJD-12000-GR designed for use with TJD-12000 Series jacks. There is most likely not a clean and easy way to remove...
  view full answer...


• Replacement Trailer Jack For Rice Trailer That Currently Has Ram 14K Jacks
  
• The Ram 14K jacks don't have a replacement rod and nut available like the 12K # TJD-12000-RODNUT and are no longer available in that capacity. I recommend changing out your jacks for the 12K option. You can use the Bulldog Side Wind Jack Assembly - 12,000 lbs # BD182513 or the Buyers Products # 3370091410H or # 3370091415H as a replacement. These are all excellent products for the price to help your trailer function as intended.
  view full answer...


• Are Bulldog and Stallion Jack Replacement Parts Interchangeable
  
• The Stallion brand of jacks has no relationship to Bulldog products. This was confirmed by my Bulldog contact. It does happen that a product design can be copied by a competitor. This could, theoretically, mean the copycat brand's customers could potentially use parts from the original maker's product, which would save the copycat company the big expense of supporting "their" product with replacement parts. That parts support may not sound like a big deal but I can assure you that a...
  view full answer...


• How to Replace Interior Ram Jack Rod and Nut # TJD-12000-RODNUT on 12000 Series Jacks
  
• Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears # TJD-12000-RODNUT in the # 12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically, you will not need to remove or cut the steel plate inside the top of the jack to do this. You will want to remove the cap, then the roll pin that holds the cross shaft into the leg, this will free up the smaller gear that will be removed...
  view full answer...


• Replacement Parts for Square Jack 12,000 lbs
  
• The Replacement Rod, Nut, and Grease Trap for etrailer and Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT replaces the ACME rod, lift nut, and grease trap on your jack. The overall dimensions of the rod are 17-3/4 inches long and 1 inch in diameter. The lift nut fits 3-1/2 inch square jack inner tubes. I have attached out return policy to assist if it isn't a fit. You can also find this under our customer service tab on our website.
  view full answer...


• Replacement Screw Kit for Older Ram 10K Jack
  
• The replacement jack screw nearest to your description is part # TJD-12000-RODNUT that you referenced. This is a rod, nut, and grease trap assembly for Ram 12K jacks. This fits jacks with an square inner tube of 3-1/2 x 3-1/2-inches. The rod overall measures 17-3/4-inches long x 1-inch diameter. If this part does not match yours we can still help you with a new jack. I linked our main page for all types of jacks. Just click on your jack type, weight rating and preferred mounting method...
  view full answer...


• Bolt-On Side Mount Caster Wheel Tongue Jack to Replace Fulton 1000-lb Jack
  
• We do sell replacement jack parts including the main screw like the one shown in your photo. Examples of these replacement jack screws are # TJD-12000-RODNUT, # BD500250 and # BD500217 which are shown on the linked page. Unless you can positively identify the model of Fulton jack you have I strongly recommend replacing the whole jack instead of trying to rebuild the old one. You may even save money by getting a new jack; you'll also get a new warranty and have the confidence of knowing...
  view full answer...


• Thread Pitch of Replacement Rod and Nut for TJD-12000 Direct Weld Jacks
  
• We do not have this item in stock for me to measure its thread pitch but two of us estimated it as being 6 or 7 threads per inch. I linked a photo of the instructions to replace this part. The bearing is removable and is available as a replacement part # TJD-12000-BR.
  view full answer...


• What Brand Jacks Does Replacement Rod and Nut TJD-12000-RODNUT Fit
  
• If the jack you have is the brand RAM then yes the part # TJD-12000-RODNUT would work for it. We have it branded for etrailer.com jacks but they also fit RAM jacks.
  view full answer...


• Replacement Handle Recommendation for Ram 12000 Series Jack
  
• For the Ram 12000 Series jacks the replacement handle is the part # TJD-12000-HD.
  view full answer...


• Replacement Rod and Nut for a Ram 12,000 lb Trailer Jack
  
• The closest option we have for you is the Replacement Rod and Nut part # TJD-12000-RODNUT which measures 17-3/4" long x 1-1/2" diameter. If you have a Ram 12,000 lb Direct Weld Jack then chances are this is the correct replacement rod and nut kit for you. Is there a label on your jack which has a part/model number? If so let me know what that is and I will see if we have another option for you.
  view full answer...


• Does Replacement ACME Screw Rod # TJD-12000-RODNUT Work for RAM Brand Trailer Jacks
  
• I would almost guarantee that the # TJD-12000-RODNUT is the correct part you need since you said you have a RAM brand trailer jack. This is designed to fit square RAM jacks like what you have so this would be what you'd want most likely. Feel free to email me a picture of what you have though and I'll take a look.
  view full answer...


• Replacement Nut for Ram Series 12000 Jack
  
• The Replacement Rod, Nut, and Grease Trap # TJD-12000-RODNUT is a fit for the 12000 series of Ram or etrailer jacks such as # TJD-12000SP-R2. It is specifically designed for square, direct-weld TJD-12000 Series jacks; the lift nut will fit 3-1/2" x 3-1/2" square jack inner tubes. If this matches the description of your jack it will work for you.
  view full answer...


• Option For Wanting to Upgrade Ram Jack to Powered Landing Gear
  
• The Ram 12000 jack that you have can have the motor kit part # BD1824200100 that you mentioned added to it to convert it a powered jack.
  view full answer...


• Repair Parts and Replacement Jack for 2000 Sundowner 2-Horse Gooseneck Trailer
  
• We do offer repair kits for many jack types, brands and models but we do not have a way to look up the specific brand and model of jack on your 2000 Sundowner gooseneck. From my research it appears most of the 2-horse gooseneck trailers from Sundowner used a single square jack, like the Bulldog 10K square jack # BD182804. This is a weld-on jack. We also have a Bulldog bolt-on 12V electric jack, part # BD185400 rated for 12K. If you can find brand and specific jack model information...
  view full answer...


• Replacement Top Cap for RAM Square Tube Jack
  
• It sounds like you are seeking the cap for the top of your square jack. The Replacement Cap for etrailer and Ram Square, Direct Weld, Sidewind Jack # TJD-12000-CP will fit the 4 x 4 inch outside square jacks.
  view full answer...

Do you have a question about this Accessories and Part?