Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
(104 reviews)
Price: $257.44
In Stock
Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
Item # LC179014
Our Price: $257.44
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (104)
- Q & A (0)
- Videos (1)
- Photos
Lippert Accessories and Parts - LC179014
- Camper Jacks
- Trailer Jack
- Legs
- Follow Leg
- Lippert
Replaces your power landing gear follow leg and snap pin. Enjoy the power setup while you are out camping and know that your RV or fifth-wheel will be steady and secure.
Features:
- Replaces your follow leg and snap pin for Lippert Components power landing gear
- Fits standard power landing gear
- Supports your 5th wheel to prevent unwanted movement
- Constructed of sturdy steel with a black powder coat finish
- Made in the USA
Specs:
- Weight capacity:
- Manual crank: 4,000 lbs per leg
- Single motor: 2,500 lbs per leg
- Dual motor: 4,000 lbs per leg
- Overall height: 32"
- Width: 2-1/2"
- Outer tube height: 29-1/2"
- Distance between bracket stops:
- Outside to outside: 17-1/2"
- Inside to inside: 15-1/2"
- 1-Year limited warranty
179014 Replacement Follow Leg and Snap Pins for Lippert Components Landing Gear
Video of Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Lippert Components Trailer Jack LC179014 Review
Speaker 1: Today I'm going to take a look at the replacement fifth-wheel RV landing gear follow leg with the snap pin for Lippert Components RVs. This will replace your follow leg and snap pin on the Lippert Components power landing gear. It's designed to fit the standard power landing gear, supports your fifth-wheel to prevent unwanted movement. It's designed to connect right here to the lead jack and the landing gear set, with a connecting rod or a cross shaft, which we do sell separately. It does include the two zerk grease fittings, one right here, one right here for lubrication of the jack. This is constructed of a heavy-duty steel, has a nice black powder coat finish to it.
Part is made in the U.S.A.A few specs on this, the weight capacity. If it's a manual crank is going to be 4,000 pounds per leg. If it's a dual motor, it will be 4,000 pounds per leg. And if it's a single motor it'd be 2,500 pounds per leg. Overall height, which will be measured from the top to the very bottom of the inner tube right there, if we put a tape measure on that right here ...
Very top here you're going to see is right at 32 inches overall height. Total width on this going to be right at 2 1/2 inches wide. Now the outer tube, which is the black portion from here to the very bottom on the black tube, that's going to be right at 29 1/2 inches tall.And then the bracket stops or the weld stops right here on each side. This is where your jack will attach to the mounting brackets on your trailer. Outside the outside, which will be from here to down here.
You're going to be looking right at 17 1/2 inches, and inside the inside, 15 1/2 inches. So, each weld stop is about an inch wide. But that should do it for the review on the replaces fifth-wheel wheel RV landing gear follow Leg with the snap pin for the Lippert Components RVs.
Customer Satisfaction Score:
95% were satisfied with this product
5% of customers were not satisfied
- Wrong item was ordered
- Wrong item shipped
- etrailer mistake
Customer Reviews
Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs - LC179014
Average Customer Rating: 4.9 out of 5 stars (104 Customer Reviews)
Replaces your power landing gear follow leg and snap pin. Enjoy the power setup while you are out camping and know that your RV or fifth-wheel will be steady and secure.by: David 08/22/2023
Need to see my response under the Lead landing gear. Perfect fit and easy installation.
by: Rene 05/22/2023
Needed a new landing leg for my 5th wheel, You guys made it soo easy to find the right part, and a great price, great quality, and fast shipping.
by: Richard03/15/2018
Landing gear works great just like original equipment. It took about 7 hrs. to remove and install due to very tight working quarters and I am pretty handy with all the proper tools needed and some, so be patient, not as easy as the you tube video I saw.
by: Greg11/16/2023
They are easy to install and work great.
by: Bill 08/19/2022
Great people! Love working with them!
Bill
8/24/2023
Still working as expected.
by: Patricia10/09/2023
Thank you for your assistance. Not only did we finally get the correct part but also assisted in being able to ship back the "wrong part". Not to mention the quick delivery.
by: John09/21/2023
was a direct fit. worked great.
by: William 08/22/2023
Shipping was fast however still have not installed yet.
by: Roger 04/26/2023
The part was delivered very promptly, was of good quality, and was easy to deal with sales staff. The part was also reasonably priced. I would recommend this company to my friends for sure.
by: Anthony Romeo09/09/2016
Product is better than new, love the added grease fittings(zerks), this will provide a way to lubricate them for a much longer lasting.
I received the product sooner than expected from ETRAILER, however our local UPS could not deliver for a few days due to stormy conditions.
I installed the jack this morning and was back in operation sooner than expected.
Great product, great service and super customer service representative (John) to work with.
Thank you
Anthony R.
9/9/2017
Great, very happy with product
by: David03/18/2023
these fit my camper just like the original's and have had no issues with them in the past year of camping
by: doug k09/08/2016
great product with easy install ,customer service and knowledge is fantastic,you have a customer for life
by: Stanley09/14/2018
Fit perfect. Exactly as described and fast delivery . A replacement follow leg for my 5th wheel...Great company to get products from.
Stanley
9/14/2019
Flawless....
by: Guy N.01/23/2017
I replaced both the left and right side landing gear jacks and they fit perfectly and were easy to install. They also have the zerk fittings so they can be greased.
Guyn
1/24/2018
no problems after a year, working fine.
by: LC17901409/13/2018
Donna was a great help getting our order for a front landing leg. Called on Monday am and order was received at our destination by Wednesday, today with a short time had the leg replaced. Great customer service!!!!!
Lc179014
9/13/2019
The leg is working great, knowledge staff, great products and fast shipping.
by: Ron L.09/23/2016
Several teeth were broken off or worn down, on my following leg landing gear, on our 2005 Keystone Challeger 5th wheel camper. our local dealer wanted $500+ to remove it, and reinstall a new one. After some on-line searching, I found this etrailer.com website. After looking at reviews, I followed their recommendation, and ordered the LC179014 leg and gear. I put in the order late afternoon on Wednesday, and it was on my doorstep Friday afternoon!!! I took the old leg out. The new leg would not "seat" correctly, and I was concerned I had made a mistake purchasing it. After doing some investigation, I found a bead of weld - on my camper - was preventing the leg from locking in place. I ground it off with my angle grinder, and the new leg fit PERFECTLY!! This new replacement weighs about 4 pounds more and is heavier constructed than the original. Plus the fact, there are grease zerks on the new, so it can be properly lubricated - unlike the factory one! In summary, THANK YOU e-trailer.com for a fantastic part!! You saved me about $400. I will be using your website again!! Ron
by: Janice L08/20/2016
We ordered the landing gear follow leg for our fifth wheel trailer free shipping was a plus. The leg arrived a 2 days earlier than expected another plus. The leg fit perfectly after we discovered that the original leg had been bent and twisted slightly from the previous owners. We were able to make a few adjustments and we installed the new leg with no other problems. All in all the job took a little longer because of the damage we had to fix but went smoothly after that. Will use e-trailer again. Thank you Michelle for your assistance, God bless
by: Joseph 01/04/2023
The packaging was insufficient for the product, but the sales representative was helpful, the package was delivered timely and the product seems to work well so far.
by: Jerry04/12/2018
Received my 5th wheel landing gear on time & installed on trailer.....functioned landing gear after installation & worked perfectly...saved a ton of money on what the cost would be from RV place...took about 1 hr. & fit like a glove...anyone can do it....thanks for help...great info. on web site...have ordered from them several times & will order from them again for my trailer needs
by: Frank m01/15/2018
Ordered both legs, U-Tube said about and jour or so. Took 3.5 hours, but what a great learning experience. Goes quicker if your storage compartment is emptied before you start!
Frank M.
1/15/2019
Great
Frank M.
1/15/2019
All is good. Thanks for your help. We still have the 5th wheel, and all seems to be working fine. Fifth wheel put away for the winter, excited to continue our journeys.
by: Larry S09/17/2018
First i would give 10 stars if i could, my part was lost in shipping by ups, i called Pat in customer service and Boy what service, she shipped out another part that day, Thursday and i received it on Friday, the next day. Everything fit perfectly, to those of you that need to order this part check all the measurements and if your are the same it will fit with out alterations . I just can't say enough about this company and this is the very first time i have used them, it won't be the last and i have told all my RV friends that this is a company that cares.
Thank you Pat and all of the employees that were involved in making this experience with your company go so well.
Larry S.
9/18/2019
product works great and has solved the problems i had. I have been telling everyone i know that if you need parts for your RV you must call Etrailer first you wont be sorry.
by: Richard H.07/20/2017
I am the original owner of a 2010 Montana Mountaineer 5th wheel. I replaced both the lead and follow landing gear. I studied the different landing gear available, and chose to try the cheaper items. These less expensive ones LC179014 and LC179013 were exactly the same as the old ones. Installation went smoothly, and they fit perfectly.
by: Dr H09/29/2016
If anybody need to know how to install a landing gear leg on a Grand Junction, feel free to contact me.
The parts came in good, the customer service was good. I wish they would have let me know that they were waiting on the small bracket but when I asked about it they were very up front about it. SO I am very pleased with everything.
This is a very good internet company to deal with.
by: Kody10/30/2017
Product shipped fast and was relatively easy to install. With some difficulty from the fifth wheel bolts (that were previously installed backwards), the legs fit perfectly. Both work in harmony and I cant wait to use them full time this coming summer. The grease zerks will also be a nice compliment, as the prior ones did not have them, which is why I'm suspecting they faltered in the first place. Will be doing business again with etrailer.com!!!
by: Ron H05/03/2017
The Landing Gears have worked flawlessly for the last year. I have lubricated them once using Valvoline Multipurpose Grease #615.
Ron H.
5/5/2018
The 5th wheel landing gears are doing great!
25
104
Show More Reviews
See what our Experts say about this Lippert Accessories and Parts
- Difference Between Stromberg Carlson and Lippert Replacement Landing Gear Follow LegsStromberg Carlson Follow Leg # LG-179014 and Lippert Follow Leg # LC179014 are basically the same. Stromberg Carlson purchases parts from Lippert so a lot of their products are nearly identical to each other.
view full answer... - What to Do if Landing Gear Leg on Trailer is BentIf your landing gear leg (inner or outer leg) is bent then I strongly advise replacing it. A bent leg can be an indication of other unseen damage. We have numerous replacement legs available for both the lead leg and the follower leg. But it depends on the model of your system. For the most part, landing gear legs are interchangeable amongst manufacturers but there are some exceptions and you still need to get one that is the right height. If you know the make and model of the landing...
view full answer... - Replacement Follower Leg for Atwood Landing Gear on 2006 Sunnybrook 5th WheelThe replacement landing gear leg follower leg for your Atwood system I recommend is the Replacement 5th Wheel RV Landing Gear Follow Leg # LC179014. I've attached a photo to help you with the weld stop locations for installation.
view full answer... - Replacement Landing Gear For 5th Wheel Campers In order to determine whether or not the Replacement 5th Wheel RV Landing Gear Follow Leg part # LC179014 will replace your current landing gear legs, you will need to measure the distance between the bracket stops. The distance between the outside brackets is 17-1/2" whereas, the distance from the inside mounting brackets is 15-1/2". You could also provide me with the model number of your landing gear and I would be able to recommend an exact fit replacement. I have attached a photo to...
view full answer...
- How is Overall Height Measured on Replacement 5th Wheel RV Landing Gear Follow Leg LC179014Overall height of a landing gear leg such as # LC179014 is measured with the jack legs fully retracted and does not include the additional length of an extended inner leg or drop leg. That is probably where the discrepancy is coming from.
view full answer... - Replacement Follow Landing Gear Leg For 2009 Keystone Fuzion Toy HaulerFrom our research your 2009 Keystone Fuzion travel trailer has Venture landing gear on it from the manufacturer. You should be able to use the Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear part # LG-179014 to replace your follow leg but you want to make sure your leg measures 29-1/2". Since you cannot get to the landing gear, if you can find a brand of the landing gear it would be very helpful.
view full answer... - Replacement for Damaged Follow Leg on Landing GearIn order to choose the correct replacement follow leg, you will need to know the manufacturer or model number, which should be visible via a sticker or stamp somewhere on the landing gear. The reason for this is there may be slight differences that cause imbalance if the landing gear legs do not match. So if you have Lippert Components power landing gear then the correct replacement follow leg would be # LC179014. I have added a link to our page with each of our follow legs for you to...
view full answer... - How to Figure Out What Landing Gear is on a 2015 Heartland Gateway 3650BHThe overall height of the Replacement 5th Wheel RV Landing Gear Follow Leg # LC179014 is 32". Since landing gears should always be installed in sets (unless you are using an exact replacement) it isn't surprising that the follow leg doesn't have any identifying marks on it. Try checking your lead leg and the motor (if you have one) to see if there are any marks on it. If you still can't find anything then you can contact Heartland with the VIN on your 2015 Gateway 3650BH and they should...
view full answer... - Replacement Follower Leg Recommendation for Landing Gear on Forest River RVI have attached a link to our selection of follow landing gear legs for you to filter through. You will want to replace your current landing gear leg with an exact replacement to avoid any differences in gear ratio which would result in an uneven trailer leveling system. Since Lippert is one of the leading manufacturers when it comes to trailer parts it is very likely that you will need the Lippert Replacement 5th Wheel RV Landing Gear Follow Leg # LC179014 which is rated for 4,000 lbs,...
view full answer...
- Determining If Replacement Landing Gear Leg LC179014 Fits 2005 Pilgrim 27 5th Wheel TrailerI would be happy to help! The Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs # LC179014 you were looking at has a main tube measurement of 29-1/2" as you mentioned, but has a weld stop dimension of 15-1/2" from the bottom of the upper weld stop to the top of the lower weld stop, and 17-1/2" from the top of the upper weld stop to the bottom of the lower weld stop. We do not currently carry and landing gear legs with 13-1/2" between the weld stops, but a qualified...
view full answer... - Can Inner leg be Removed From Out Leg Of Lippert Landing Gear On Fifth Wheel TrailerPer our technical contact at Lippert Components they said that on their landing gear legs such as the follow leg part # LC179014, the outer tube has two pinch points that are intended to prevent the inner tube from extending too far. The pinch points are also intended to prevent the inner tube from completely leaving the outer tube. My contact also said that for safety reasons it is not recommended to try to repair this jack leg, and it should just be replaced.
view full answer... - Replacement Follow Leg for 2018 Palomino Puma 286-RBSSThank you for the pictures you submitted of the landing gear leg you need to replace. Based on that the correct follow leg you need for your Palomino is the part # LC179014.
view full answer...
- Follow Landing Leg Replacement Needed for a 2017 Forest River Blue Ridge 3780LFI have attached a link to our selection of follow landing gear legs for you to filter through. You will want to replace your current landing gear leg with an exact replacement to avoid any differences in gear ratio which would result in an uneven trailer leveling system. Since Lippert is one of the leading manufacturers when it comes to trailer parts it is very likely that you will need the Lippert Replacement 5th Wheel RV Landing Gear Follow Leg # LC179014 which is rated for 4,000 lbs,...
view full answer...
- Replacement Landing Gear Follower Leg for a 2010 Keystone Fusion 5th Wheel TrailerThe landing gear on your 5th wheel trailer is likely made by Lippert. Check the motor/lead leg to see if there is any indication of the manufacturer. If it is a Lippert system and the old follow leg has an outer tube height of 29-1/2 inches then this is the correct replacement follow leg. If you come up with a different manufacturer or outer tube measurement let me know.
view full answer... - Replacement Lippert Landing Gear Follow Leg for 2009 Crossroads CruiserThe Replacement 5th Wheel RV Landing Gear Follow Leg # LC179014 that you were looking at is exactly what you need to replace the follow leg for your Lippert landing gear system. Just like your existing leg this unit features an outer tube length of 29-1/2 inches, a distance of 15-1/2 inches between the bracket stops, and a distance of 17-1/2 inches when measuring outside to outside on the bracket stops. I have attached a short video demonstration that you can also check out.
view full answer... - Replacement Venture Landing Gear Follow Leg for 2006 Hitchhiker 5th Wheel Trailer The Replacement 5th Wheel RV Landing Gear Follow Leg # LC179014 referenced in your question is the closest option we have to the measurements you provided in your question. As you mentioned, this particular leg features a distance of 15-1/2 inches between the bracket stops inside to inside and a 17-1/2 inch distance between the stops outside to outside. The leg itself (outer tube) measures 29-1/2 inches and has a width of 2-1/2 inches x 2-1/2 inches. From the top bracket to the top of the...
view full answer... - Replacement Landing Leg for 2013 Cedar Creek Sliverback 29REThe replacement follow leg you will want for your 2013 Cedar Creek Silverback 29 RE is the Lippert Components Replacement 5th Wheel RV Landing Gear Follow Leg with Snap Pin # LC179014. I spoke with Cedar Creek to see which manufacturer's landing gear they use on the Silverback campers. They were able to tell me that your camper has Lippert landing gear.
view full answer... - Replacement Follower Leg Recommendation for 2003 Keystone Challenger with 4,000 lb CapacityThe leg you need is the part # LC179014. This is a replacement follower leg that will fit your 2003 Keystone Challenger and has a 4,000 lb capacity.
view full answer... - How To Determine The Correct Replacement Landing Gear For A 2009 Keystone Laredo 245RLIn order to determine the correct landing gear for your 2009 Keystone Laredo 245RL, you're going to need to measure the distance between the two weld stops, like illustrated in the diagram attached. From here, you can choose a replacement that will give you the correct amount of lift, and weight capacity needed. For example, the Lippert Electric Landing Gear Set # LC333964 has the standard 17-1/2" from the weld stops, 34-7/8" of lift, and a 6,500-lbs capacity.
view full answer...
- Replacement 5th Wheel RV Landing Gear Legs for a Terry 5th Wheel Series M-21 L5B TrailerIn order to choose the correct replacement landing gear legs for your Terry 5th Wheel Series M-21 L5B Trailer, I would need to know the overall length of the outer tube in addition to the distance between the weld stops. I have attached a photo of these measurements for you. If the outer tube on your landing gear legs measure to be 19-1/2" long and the weld stops are 15-1/2" apart then you can use the Replacement 5th Wheel RV Landing Gear Leg part # LC179014 for follow or part # LC179013...
view full answer...
- What Holds Inner and Outer Landing Gear Tubes Together on Lippert Landing Gear Follow LegThank you for the photo of your 5th wheel landing gear leg. My technical contact at Lippert Components confirmed that on their landing gear legs such as this follow leg # LC179014 the outer tube has two pinch points that are intended to prevent excessive extension of the inner tube. These pinch points are also intended to prevent the inner tube from completely leaving the outer tube. My contact indicated that for safety reasons it is not recommended to try to repair this jack leg; it should...
view full answer...
- Difference Between Landing Gear Follow Leg Replacements # LC119101 and # LC179014There really isn't a difference between the # LC119101 and # LC179014. One is just listed for Venture landing gear sets and the other Lippert. They are both identical though.
view full answer... - Replacement Follow Landing Gear Leg for Venture Landing Gear on 2000 Keystone Mountaineer 5th WheelIt sounds like you're looking for a replacement follow leg for your Venture landing gear. If this is the case, I recommend the Lippert Components Replacement 5th Wheel RV Landing Gear, Follow Leg # LC179014. This follow leg has an out tube that measures 29-1/2 inches long and is 2-1/2 inches wide. The bracket stops on this replacement leg measure 17-1/2 inches. The # LC179014 comes with the drop leg and snap pin for easy replacement of your existing follow leg. The gears for the leg...
view full answer... - Replacement Landing Gear Leg for Atwood Lead LegAtwood has been bought out by Lippert and for your replacement I recommend the Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013 and get the matching follow leg # LC179014. This will give you a matching set so they will operate at the exact same speed and strength. These legs are 29-1/2 inches long outer tube (32 inches total). These legs have the 2-1/2 inches outer tube width.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Installed by:
Jeff D
Updated by:
Laura H
Updated by:
Shelly K
Updated by:
Wilson B
Updated by:
Mike S
Written by:
Chelsea B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Richard
3/15/2019
Still working properly, I’ve had no issues with it...