What is the Difference Between the Landing Gear Set RVLG-8HDL and RVLG-8000?
Updated 04/02/2025 | Published 03/24/2025 >
Products Featured in This Question
Question:
What is the difference between your RVLG-8HDL and your RVLG-8000 . I am looking to replace the current jacks on my wolf pack 5th wheel toy hauler.
asked by: Bobby G
Expert Reply:
Hey Bobby! As far as the jacks go for item # RVLG-8000 and item # RVLG-8HDL there is absolutely nothing different. The item # RVLG-8HDL comes with the manual handle that I have attached a picture of below. That is the only difference.
If your 2019 Cherokee Wolf Pack toy hauler has brackets that are 2" tall then you most likely have the standard weld stop measurements of 15-1/2" inside to inside. I have attached a photo so you can compare these dimensions to your current set up. If these match up, I recommend the Landing Gear Set w/ Handle item # RVLG-8HDL over the item # RVLG-8000 because not only does it come with the handle but for some reason as of (3/30/2025) it's less expensive.
If you have any additional questions feel free to throw them into the comment box below and I'll be happy to help you.
Product Page this Question was Asked From
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 7001 - 8000 lbs
- Manual Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: accessories and parts
- Search Results: landing
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Search Results: lc142178
- Search Results: landing gear
- Search Results: stabilizer
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Video: All You Need to Know About the Landing Gear Set
- Search Results: trailer side marker lights
- Search Results: trailer side marker
- Shop: Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs
- Video: In-Depth Review of the Landing Gear Set
- Q&A: How to Determine Correct Replacement Landing Gear For 5th Wheel
- Q&A: Is there a Way to Identify 5th Wheel Trailer Landing Gear with No Markings
- Video: All About the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Q&A: Replacement Landing Gear for a 1996 Sea Breeze 5th Wheel Trailer
- Shop: Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Q&A: How To Install the Landing Gear Set Part # RVLG-8000
- Shop: Lippert Electric Landing Gear Set - 37" Lift - 6,000 lbs
- Q&A: Motor Kit Needed to Convert etrailer Landing Gear RVLG-8000 to Powered
- Q&A: Comparing the Stromberg Carlson Replacement Motors LG-196308 and LG-142178
- Q&A: Picking Out Replacement Landing Gear for 2010 Sandstorm Fifth Wheel
- Video: Ultimate Overview of the Lippert Electric Landing Gear Set
- Video: The Low-Down on the Replacement Motor for Stromberg Carlson Electric Landing Gear
- Shop: Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear
- Video: Complete Breakdown of the Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Video: All You Need to Know About the Optronics LED Clearance or Side Marker Light
- Shop: Suspension Enhancement
- Shop: Fifth Wheel Hitch




Bobby
4/1/2025
Thanks Jarred, yes I have the 2” and weld stops are standard. My current system does have manual crank but I have the electric motor and only use handle if needed, again thanks for the info.