Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
(118 reviews)
Price: $193.84
Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
Item # LC179013
Our Price: $193.84
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (118)
- Q & A (0)
- Photos
Lippert Accessories and Parts - LC179013
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
- Lippert Components Power Landing Gear is standard on most fifth-wheel RVs produced today. This replacement lead landing gear drop leg and snap pin will get you back to camping and enjoying the great features of your power landing gear. This kit includes the landing gear lead leg and snap pin and is easy to install with minimal assembly required.
- Kit includes landing gear lead leg and snap pin
- For use on LCI Power Landing Gear assemblies
- Easy to install
- Minimal assembly required
- Black powder coat finish is corrosion resistant
- Grease zerk fitting makes maintenance easy
- Made in the USA
- Weight capacity:
- Manual crank: 4,000 lbs per leg
- Single motor: 2,500 lbs per leg
- Dual motor: 4,000 lbs per leg
- Overall height: 32"
- Outer tube width: 2-1/2"
- Inner tube width: 2-1/4"
- Outer tube height: 29-1/2"
- Travel distance: 21"
- Drop leg travel: 16"
- Can be adjusted in increments of 1", leaving the bottom hole for installation of footplate
- 1-Year limited warranty
179013 Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
- Alternate product found
Customer Reviews
Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin - LC179013
Average Customer Rating: 4.8 out of 5 stars (118 Customer Reviews)
by: Josh08/13/2023
I ordered 2 jacks to replace on my fifth wheel camper, one jack didn’t have any grease in it and was not easy to move up and down causing my gearbox to break so hard to replace the gearbox and it still doesn’t go up and down very easily. Not very happy with the jacks.
by: Aristides05/07/2024
A little more of a challenge to get this component installed into my rig, however it fit perfectly! Odelia is always a reliable resource.
by: Tom 04/10/2024
EZ to install. Highly recommend this company and this product.
by: David 08/22/2023
Received quickly, and installed that afternoon. Easily fit right back into clamps. Was expecting to make some kind of adjustments. No problem at all. Etrailer staff knew what they were talking about. Understood what I was mumbling and got me the right parts. Great people, hats off to Quinn and Nickolas.
by: Sammy03/20/2022
Great service and timely delivery and Thanks Steve Z for helping me pick out the parts I needed for my Trailer. The Jacks fit perfectly
by: Ronnie 01/18/2024
Four nuts and bolts, old one out and new one in, took 30 minutes, with a smoke break.
by: Daniel06/04/2018
The parts were exactly what I ordered and better than the OEM parts. It took only an hour to replace the OEM landing gears.
by: Greg11/16/2023
They are easy to install and work great.
by: Danny06/12/2022
Fast Delivery, excellent price, great customer service!
Danny
6/13/2023
Still working as it should, I do appreciate your speedy delivery, since I was camping at the time the part broke, thx again
Mike L.
9/6/2023
@Danny We're glad that the # LC179013 replacement landing gear leg worked well for you!
by: John09/21/2023
was a direct fit. worked great.
by: Russell09/19/2019
Product shipped fast. As per some reviews I had to modify the tabs to get it to fit. I ground off about 1/16" with a cut off wheel on my die grinder. This leg works great and comes with 2 zerk fittings which my OEM did not have. The zerks are better than nothing but I used a piece of PVC packed with grease to lube the jack screw.
Russell
9/20/2020
Still working great!
by: paul k06/16/2015
the landing gear drop legs look good they even have grease fittings for the gears and shafts the original ones did not . I will install them in about a week . the price was very good they were on back order but worth the wait thanks paul
Paul K.
6/15/2016
legs work great very good product
by: Edward 08/15/2022
I ordered the complete landing gear for my 2006 Thor 5th wheel. As I have always in the past been satisfied with the quick service and quality of the components. Installation was pretty straightforward. I will continue to order all my hardware from etrailer as done in the past. Great customer service over the phone and quick delivery of the parts.
by: Michael04/19/2019
Great experience from start to finish! Bryan provided competent professional customer service. The items arrived sooner than I expected and were a perfect fit for my RV. Installation was easy and quality of the parts is superb. I am a huge fan of etrailer.com!
Michael
4/20/2020
The parts have been on the RV for a year now and still work perfectly!
by: Guy N.01/23/2017
Good product easy to install, perfect fit for my trailer. Also gas 2 zerk fittings for grease.
Guy N.
1/24/2018
Still working great
by: Wayne09/12/2022
I had bent the inner shaft on this landing gear because I did not raise it enough before moving. The new landing gear fit perfectly and videos spelled out each step. Very pleased with the replacement.
by: Clyde12/08/2017
Have purchased from etrailer off and on for several years. Have always found the products to be good quality, reasonably priced, and shipped promptly. Thanks!
Clyde
12/8/2018
Working great!
by: Stan O.12/18/2016
Everything fit and works perfect, excellent customer service over the phone. Would definitely buy from etrailer again
Stan O.
12/18/2017
Thanks...and a Merry Christmas....it has been working without fail....
by: Richard 09/24/2020
I had to weld a 5/8” piece a flat steel above the lower weld stop in order to fit my 5th wheel but any replacement jacks would have required this modification. There are 2 grease zirk fittings and fortunately I can easily get to them. Just a quick bolt in replacement.
by: Linda01/03/2019
The lead leg went on our 2006 Keystone Montana Mountaineer and was an exact fit. Order just the gears but before came realized needed to replace whole leg. Called and spoke with customer service and sales, they sent me a return slip and my item was returned per their policy with no problem. They were very helpful and knowledgeable, to help me get what I needed for sure. Product arrived quickly, easy installation, and now ready to enjoy summer. Ordered from etrailer before, they are a wonderful, knowledgeable company to keep our equipment operational. They get a A+ for customer service.
by: Ron H05/03/2017
The landing gears have work flawlessly. I have lubricated them once with Valvoline Multipurpose Grease #615.
Ron H.
5/5/2018
The 5th wheel landing gears are doing great!
by: Doug10/26/2019
I called my order in so I could ask the questions to make sure it was the correct piece. Nick was very astute and understood how to help me! I first found this part without grease fittings, but she'd if I could put them in. Then, Nick found me this that already has them!
Ordering was easy. Free shipping got it here in a few days, on time. Install was easy. Popped in just like the old one popped out.
The only issue: my old one had a bracket welded onto it that would push up against a flat bracket on the trailer post. This new one did not. I'm not sure if it is necessary since this new one didn't come with it? But I cut the old one off and welded it onto this one. Took an extra half hour. Fortunately, that was easy for me... But if you don't have a welder? Just make sure to ask if it is truly necessary?!
Other than that, very pleased with their service and the product with as soon as it was installed. I'll update if it breaks early...
by: Tom08/10/2019
Landing gear has been installed for over a year and continues to function. Still quiet too.
Tom
8/11/2020
Still working fine, and it had a workout this year visiting every western state except AZ over a 10 week period. Lots of raising and lowering...
by: Butch M01/25/2020
On my 5 whl the landing gears froze up and would not turn either way. I ordered LC179013 and installed myself. That was s good job for an old 70Yrs fat man to do..
I got them installed and wired up and they work like a champ. That has been over a year ago and have been used alot.
by: Thomas 07/27/2023
Came in as expected
25
118
Show More Reviews
See what our Experts say about this Lippert Accessories and Parts
- Replacement Landing Gear Leg for VMC900R with 29-1/2 inch Outer Tube HeightThe replacement follow leg replacement you need is the Lippert # LC179013 which works and is interchangeable with Venture landing gear legs like you have and has the correct outer tube height of 29-1/2 inches.
view full answer... - Correct Replacement Landing Gear Legs for 2004 Keystone Montana 5th Wheel Big SkyThe correct replacement landing gear leg for a Keystone Montana 5th Wheel is actually the Replacement Leg for Keystone Montana 5th Wheel Landing Gear part # LC178652 for the follow leg and part # LC178653 for the lead leg. However, there are others that will work which have the same dimensions. That said, the issue you are having is that you purchased a lead leg which is for the driver side and need a follow leg, the part # LC178652.
view full answer... - Comparing Lippert and Stromberg Carlson 5th Wheel Landing Gear Lead Leg Kits The Lippert Components 29-1/2-Inch Lead 5th Wheel RV Landing Gear Drop Leg # LC179013 and the Stromberg Carlson Replacement Lead Jack with Drop Leg # LG-179013 are virtually identical. If one fits your landing gear the other will too. Lippert Components is the OEM maker of almost all trailer frames and also of many trailer accessory items like jacks and landing gear. They also make the products as OEM items sold under other brand names like Stromberg Carlson.
view full answer... - Troubleshooting Venture M-9000-PK Landing Gear on 2010 Komfort Fifth Wheel TrailerThe next step is to take apart the top of the jack and check the gears there. If you find your problem there, possibly some worn gear teeth, and you have Lippert landing gear, the repair kits are parts # LC146059 for the lead leg and # LC146060 for the follow. Another possibility is the screw down the center of the jacks has possibly gotten stripped. However, if this is the case your best bet will be to replace the legs. You'll need to measure the outer tube to determine which legs...
view full answer... - How To Find the Correct Replacement Landing Gear Legs for a 2013 Keystone LaredoIn order to find the correct replacement landing gear legs for your 2013 Keystone Laredo 335TG I would need you to take two quick measurements of your existing landing gear legs, the outer tube length and weld stop spacing. I have attached a photo to assist. The most common replacement landing gear legs are the Replacement 5th Wheel RV Landing Gear Legs part # LC179013 for lead and part # LC179014 for follow. These measure 29-1/2" on the outer tube and 15-1/2" between the weld stops....
view full answer...
- Is Lippert Components Lead Leg Replacement part # LC179013 Idle or Motor Side LegThe Lippert Components Lead Leg Replacement part # LC179013 is the leg that has the motor.
view full answer... - What Holds Inner and Outer Landing Gear Tubes Together on Lippert Landing Gear Follow LegThank you for the photo of your 5th wheel landing gear leg. My technical contact at Lippert Components confirmed that on their landing gear legs such as this follow leg # LC179014 the outer tube has two pinch points that are intended to prevent excessive extension of the inner tube. These pinch points are also intended to prevent the inner tube from completely leaving the outer tube. My contact indicated that for safety reasons it is not recommended to try to repair this jack leg; it should...
view full answer...
- Replacement Landing Gear Legs for a 2008 K-Z 5th Wheel TrailerThe correct replacement landing gear legs for your 2008 K-Z 5th Wheel Trailer are going to be the Replacement 5th Wheel RV Landing Gear part # LC179014 for the follow leg and the Replacement 5th Wheel RV Landing Gear part # LC179013 for the lead leg. The correct replacement motor is the Lippert Components Venture 5th Wheel RV Landing Gear Motor part # LC142178 and the correct replacement gearbox is the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies...
view full answer... - Replacement Driver Leg for Atwood Landing Gear Jack on CamperI wish we had access to that part number but since Atwood was bought and mostly dissolved as a brand the replacement part you are looking for is no longer available. Best option is a new drive leg as other brands will fit as a replacement like the # LC179013 which is 32 inches long, part # LG-179013 which is 29-1/2 inches, or # LG-177202 which is 33-1/2 inches.
view full answer... - Replacement Landing Gear Leg for 179013We have the exact leg part number you have now with the part # LC179013 if that's what your preference would be for a replacement. The part # LC119102 has different dimensions and would not work if you have the 179013.
view full answer... - Which Replacement Gear Kit Fits Lippert Replacement Lead Leg # LC179013Yes, the landing gear repair kit part # LC146059 that you referenced is the correct gear replacement for the leg part # LC179013 you mentioned. So if you wanted to have a spare gear kit on you this would be correct kit needed.
view full answer... - How do Lippert Landing Gear Legs Attach to a Trailer FrameThe Lippert Components 29-1/2" Lead 5th Wheel RV Landing Gear Drop Leg # LC179013 that you referenced would bolt to a trailer if it currently has Lippert landing gear on it. This would attach to the trailer's current frame brackets. If your trailer has a different brand of jacks installed currently you would need to have the frame brackets moved if they are not 17-1/2 inches apart measured form the insides.
view full answer...
- Replacement Landing Gear Leg Recommendations for Colorado Dutchmen 260RLFWWe have just what you need. The Lippert landing gear is a very common set used on RVs. So if you are looking for a replacement follower leg you'd need part # LC179017 or if you needed a replacement lead leg you'd want part # LC179013.
view full answer... - Can a Lippert Manual Landing Gear Set Be Converter to a Dual Motor SetupIf you are looking for a way to convert your landing to a dual motor setup there's really no way to do that without replacing the follow leg with a lead leg, adding a motor and gear box, adding an additional switch and eliminating the cross shaft. For a lead leg you would need part # LC179013, for a gear box # LG-179015 and then motor # LC142178 and switch kit # LG-145236. The follower leg cannot have a gear box attached to it.
view full answer... - Landing Gear With Snap Pins for Keystone SpringdaleWe do have replacement landing gear legs with snap pins, though the part you referenced is specific to the Keystone Montana, so you will need something different. Assuming you have the standard 15-1/2" inside-to-inside distance between weld stops, and your leg has a 29-1/2" outer tube then you can use replacement legs from Lippert: - Replacement 5th Wheel RV Landing Gear Lead Leg with Snap Pin # LC179013 - Replacement 5th Wheel RV Landing Gear Follow Leg with Snap Pin # LC179014
view full answer... - Replacement Lead Leg Needed for Lippert Components LG-6000 Landing GearThe Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013 is the replacement you are seeking for your 6,000 lb capacity landing gear.
view full answer...
- Replacement Landing Gear Leg and Foot Pad for a 2008 Cedar Creek 5th Wheel TrailerLanding gear jacks have a lead leg and a follower leg. The lead leg is the one the crank goes into. For example if it is the lead leg that is missing then leg # LC179013 is a likely fit. This leg has an outer tube that is 29-1/2 inches tall. The matching follower leg is # LC179014. The standard replacement foot pad for these legs is # LG-119225. If you have any part numbers on the jack leg or any distinguishing names or marks let me know and I can determine if these are a fit for sure...
view full answer... - Replacement Parts For Lippert Landing Gear LC333964 On 2020 Forest River Wolf Pack RVI can certainly help you out with finding replacement parts for your Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs # LC333964. The correct replacement motor for this setup is Lippert Venture 5th Wheel RV Landing Gear Motor # LC142178. This motor is rated for 5,000lbs on single motor 2 leg setup, and 8,000lbs on dual motor setup. If you end up needing a replacement lead leg then you can go with Lippert Components 32" Lead Leg # LC179013, and for a replacement follow...
view full answer... - What Replacement Landing Leg do I Need for My 2000 Jayco Eagle Fifth Wheel Camper?Your 2000 Jayco Eagle likely uses either Stromberg Carlson Electric Landing Gear Set # LG-1 or a Lippert setup like Lippert Electric Landing Gear Set # LC333964. You will want to confirm this, but if you need the replacement lead leg for Stromberg setup then go with Lead Leg # LG-179013 which has total lift of 34-7/8" and uses Motor # LG-217884. If you have the Lippert setup then go with Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg # LC179013 and motor # LC142178 if you...
view full answer... - Replacement Landing Gear Bracket for an LCI Landing Gear On An 2019 GD Reflection 5th WheelWe sure do! I believe you're looking for the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket for Lippert RV's # LC113511. This is a standard weld-on frame bracket that is designed to work on LCI assemblies like your Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013, and has measurements of 2" long x 3-1/2" wide x 4-1/2" tall.
view full answer... - Does Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg Come With Bolt and RetainerYes, everything you see in our product images and the review video comes with the Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013. This includes the retainer and bolt you're referencing.
view full answer... - Do Lippert Landing Gear Legs # LC179013 and # LC179014 Have Grease FttingsThere is a great chance either of the legs you mentioned would work as a replacement, but I'd need to know for sure what landing gear you have on your trailer. The Lippert landing gear like the part # LC179013 and # LC179014 are very popular and there's a strong chance this is what you need.
view full answer...
- Recommended Replacement Lippert Landing Gear Leg for a 5th Wheel Trailer I believe what you need for your 5th wheel is the Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013. This replacement leg measures 32" overall, has the same 15-1/2" inner, 17-1/2" outer measurements, and has a total travel distance of 21". I was not able to find anything that matches both the 33-1/2" overall measurement with the same inner/outer measurement. As long as you have a Lippert Power landing gear, which most modern RV's and 5th Wheels do,...
view full answer...
- Recommended Landing Gear Leg Replacement for 2007 Forest River Sandpiper TrailerFor a replacement leg for your 2007 Forest River Sandpiper trailer, I recommend the Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for Lippert Components RVs # LC179014 unless you need the lead leg and then I recommend the # LC179013. I've attached a photo to show you how this leg will attach to your current frame brackets.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Installed by:
Cole B
Written by:
Chelsea B
Updated by:
Shelly K
Updated by:
Wilson B
Updated by:
Mike S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Sammy
3/21/2023
No issues at all. Still working fine