Give your truck a finished look with a custom-fit third brake light. These LED lights with free form reflectors give you bright, clear light where you need it with the look you love, illuminating your bed much better than an OEM cargo light. Each light is equipped with a polycarbonate lens for durability and super bright LEDs which last longer and use less power than normal incandescent lights. These third brake lights use the existing factory plug for an easy installation with no cutting or splicing.
We offer many custom fit styles for popular truck manufacturers like Ford, Chevrolet, Dodge, and GM. Find the right fit for your vehicle by entering the year, make, and model to the left.
What our customers are saying:
Great merchant, fast shipping, did not markup shipping. Would buy from again.
Alan
The Colony, TX
Putco PURE Headlight Light Installation - 2007 Mazda 6
Today, in 2007 Mazda 6, we're going to install product number P230100SW from Putco. This is a pure H1 halogen headlight bulb. This is what it looked like before we install the bulbs. Now, we'll go ahead and remove the factory bulbs and install new Putco bulbs. Our headlight bulb is located on the outside of the headlight assembly towards the outside of the body. Behind this cap is the bulb and then there's a little wire latch inside it.
Blazer Light Buster Backup and Utility Light Review
Today we are going to show you the Light Buster backup and utility light for 7-pole connectors from Blazer, part number C8020. The Light Buster is designed to fit in the 7-way port on the back of your vehicle. The Light Buster has two modes, either utility mode or backup mode. To switch between the modes all you have to do is rotate the head of the light. You will notice that on the back of the light that there are three pins. The pin on the bottom right is the ground connection that is going to complete the circuit and connect to the ground on your 7-way on your truck. The large center pole is the reverse light. This pole only becomes active when you have your vehicle in reverse. The contact on the upper right is for your taillights. That means that in order to use the Light Buster in utility mode, you will need to have your vehicle headlights on. 0:54
Oval Amber Directional LED Warning Lights Review
Today we are going to show you the amber flashing hazard lights from Optronics, part number SLL72AB1 and part number SLL72AB2. The flashing hazard lights are designed to be used on emergency, road-side assistance, construction sites and off-road vehicles, along with the rubber grommets, part number A70GB and the straight 3-wire pigtails, part number A45PB. They fit the standardized 6-1/2 inch oval shaped trailer light mounting holes, using the rubber grommets. There are 24 amber LEDs covered by a lifetime warranty. The lights are designed to fit inside the grommets that will hold them snug inside your mounting points. The rubber grommets simply stretch over the lights. On the reverse side of the light there is a port for the pigtail harness. The pigtail harness just fits into the posts and pushes in snug. The wiring for your light is already done at this point. All you have to do is connect the loose ends to the vehicle. 1:03
Putco PURE LED Dome-Light Kit Manufacturer Installation - Chevy Silverado
Start by gently removing your dome light cover. Then, remove the old factory bulbs from their sockets. Install your new Pure LED lights by placing the metal brackets into the sockets. Once installed, carefully replace the cover and repeat these steps with your other consol lights as well. Congratulations, you have just installed your new Putco LED dome lights. Enjoy!
Putco PURE LED Dome-Light Kit Manufacturer Installation - Ford F-150
Start by removing your dome light. Once removed, twist the light bulb out of the dome light. Remove the factory bulb from the socket and replace it with your Putco light. Replace the dome light. And congratulations, you have just installed your new Putco LED dome lights. Enjoy!
Start by removing your dome light. Once removed, twist the light bulb out of the dome light. Remove the factory bulb from the socket and replace it with your Putco light. Replace the dome light and continue onto your other lights. Start by removing your dome light. Then remove the old factory bulbs from their sockets. Install your new Pure Led lights by placing the metal brackets into the sockets. Once installed, carefully replace the cover. And congratulations, you have just installed your new Putco LED dome lights. Enjoy!
Putco PURE LED Dome-Light Kit Manufacturer Installation - Dodge Charger
Putco PURE LED Dome-Light Kit Manufacturer Installation - Nissan Titan
Putco PURE LED Dome-Light Kit Manufacturer Installation - Ford Super Duty
Start by removing the dome light cover and then remove the middle factory bulb. Use a flathead screw driver to remove the screws. Once the screws are removed, take the dome light cover off. Make sure to unplug it. Remove the metal backing of the other two factory bulbs. Take them out and then replace them with your new Putco LED lights by placing the brackets into the socket. Plug the dome light back in and then put it back in its place by screwing it in. Replace the middle factory bulb with your new Putco LED light. Put the cover back on and repeat these steps with your other dome light. Congratulations, you have just installed your new Putco LED dome lights. Enjoy!
Replacement Automotive Lighting
