Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Darren, the studs of the Optronics Fusion LED Trailer Light #OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
Hey Sal, the Optronics Fusion LED Trailer Light #OPT45KB is for just 1, not set of 2. These are super nice, but if you want some other options to consider, we also have the Fusion LED Hardwired Trailer Light #OPT57NR which does have the same…
Hey Eli! The first thing you want to do is make sure you have brake flanges on those axles. You also need to take a look at the axle tags and find the axle capacity. More than likely they're 3,500 lb axles so I'll answer based on that. If you…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…
Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Darren, the studs of the Optronics Fusion LED Trailer Light #OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
Hey Sal, the Optronics Fusion LED Trailer Light #OPT45KB is for just 1, not set of 2. These are super nice, but if you want some other options to consider, we also have the Fusion LED Hardwired Trailer Light #OPT57NR which does have the same…
Hey Eli! The first thing you want to do is make sure you have brake flanges on those axles. You also need to take a look at the axle tags and find the axle capacity. More than likely they're 3,500 lb axles so I'll answer based on that. If you…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…
Looking to freshen up your rig, rectangle led light options give a clean look with bright, modern performance. Installs are straightforward, and you can choose single-wire mounting-ground or two-wire setups to match your wiring. A solid pick for replacing factory units or updating markers and tail lamps on boat, utility, or camper trailers.
Yes, look for models with a submersible or waterproof housing. Sonically sealed, waterproof designs help on boat trailers. Add dielectric grease to pigtail sockets to help keep water out. If a light uses a chassis ground, consider a dedicated ground wire for dunking situations.
Yes, some LED tail lights use a 3-prong triangular pigtail so you don't have to cut your existing plug. Match the triangular shape and pin count to your trailer's connector. If you need a license plate light, make sure the driver's side assembly includes it.
You can use one-wire lights that ground through the mounting hardware, or two-wire lights with a dedicated ground. If your trailer is bolted together, running dedicated grounds from the wiring harness to each light can improve reliability. Verify the ground path is clean metal and secure.
Measure your existing light's length, height, depth, and mounting hole spacing, then choose a similar-size LED replacement. Confirm the contour and footprint will cover the original area. If your mount uses a carriage bolt in a plastic track, avoid nyloc nuts that can make the bolt spin.
Clearance Lights
Interior Lights
License Plate Lights
Tail Lights
Trailer Lights Parts or Accessories
Filters
