Do Studs of Optronics Fusion LED Trailer Light Thread Out Easily

Question

Question:

Do the studs screw/turn out if a person wanted to 3M tape the lights on instead?

asked by: Darren

0

Expert Reply:

Hey Darren, the studs of the Optronics Fusion LED Trailer Light # OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to install it the way you mentioned. What are you wanting to install this on?

expert reply by: Jameson C

0

Light Assembly Back Side
(click to enlarge)

Darren

6/17/2026

2021 Northern Lite 10-2 truck camper. Was just trying to avoid drilling extra holes if possible.

Jameson C.

6/17/2026

@Darren Makes sense! I know that drilling isn't ideal but it would hold the assembly better.

Answer 1

Hey Sal, the Optronics Fusion LED Trailer Light #OPT45KB is for just 1, not set of 2. These are super nice, but if you want some other options to consider, we also have the Fusion LED Hardwired Trailer Light #OPT57NR which does have the same…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Eddie, the Curt hitch part #C22RJ and the Trailermate part #TMT29FR are both very similar in design and capacity. I really like the Curt hitches and recommend them whenever available but Trailer Mate isn't bad either. If you are wanting the…

view full answer...

Answer 12

Hey Darren, the studs of the Optronics Fusion LED Trailer Light #OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to…

view full answer...

Do Studs of Optronics Fusion LED Trailer Light Thread Out Easily

Product Page this Question was Asked From

Continue Researching