See what our Experts say about this TruRyde Trailer Spindles

• Are the TruRyde Spindle # TRU59FR and etrailer Idler Hub Assembly # AKIHUB-545-2-2K Compatible
  The TruRyde Spindle # TRU94FR and our Trailer Idler Hub Assembly # AKIHUB-545-2-2K are not compatible, but you could use the TruRyde EZ Lube Spindle # TRU44FR instead as it has the correct spindle measurements. For a hub that will work with the TruRyde Spindle # TRU94FR you can use part # AKIHUB-545-2-1K. To determine if a hub is compatible with a specific spindle you will need to make sure that the inner diameters of the Inner Bearing, Outer Bearing, and Grease Seal of the hub matches...
  view full answer...
  
• Replacement Axle Options For A Trailex SUT 200 Boat Trailer
  That is a very unique trailer you have, Gordon. Maybe a little too unique. We have spindles that you could use as replacements (1-3/8" Diameter Stub # TRU59FR, 1-1/4" Diameter Stub # TRU94FR, or 1-1/2" Wide (square) Stub # TRU97FR) that all have a 1" shaft for the bearings (which would be part # L44643). That axle is going to be too short for us to have anything that would work, unfortunately. What I would probably do would be grab two of these spindles and some tubing that will slide...
  view full answer...
• Compatible Hub for TRU44FR BTR Spindle
  The # TRU44FR spindle you'd looked at is compatible with an L44649 inner and outer bearing, like what's used by the # CE13109. The hub includes the inner and outer bearing and race, the grease seal, the dust cap and the lug nuts. The hub has a 4 on 4 bolt pattern. For a 5 on 4-1/2 inch bolt pattern, use # AKIHUB-545-2-LFEZ-2K.
  view full answer...
• Spindle Compatible With Trailer Idler Hub Assembly AKIHUB-440-2-1K
  The Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased # AKIHUB-440-2-1K won't fit your trailer spindle as it will be too long. The reason is, this hub is designed to work on BT8 spindles, which are longer than what you have. The only solution we can offer is to replace your short and older spindles with a new one that will work with the Trailer Idler Hub Assembly # AKIHUB-440-2-1K, which is the BT8 Spindle for 2,000 lb Trailer Axles # TRU59FR. I have...
  view full answer...
• Replacement Trailer Axle Spindle that is 1 inch Diameter and Uses Bearings l44643
  Hey Douglas, thanks for all of the info you listed on your spindle. Based on that the correct replacement would be the BT8 part # TRU59FR. Did you damage your old spindle?
  view full answer...
• Recommended Hub W/ Integrated Drums for a BT8 Spindle
  Charles, it looks like none of our hubs with integrated rotors are going to work with your BT8 Spindle # TRU59FR. We do have the DeeMaxx 10" Hub/Rotor Assembly # DE49VR which will work with 3.5K axles and has a 5 on 4 1/2" bolt pattern, but nothing for your BT8 spindle. We do also have hubs with integrated drums like the Easy Grease Trailer Hub and Drum Assembly for 2K Axles # AKHD-545-2-EZ-1K which will work with your BT8 spindle.
  view full answer...
• How to Determine the Correct Replacement Spindle With Bearing 07100
  Bearing 07100 are older bearings with the same dimensions as bearing # L44643. The spindles that uses those inner and outer bearings are # TRU94FR and # TRU59FR. The difference between these is one measurement, the furthest outer diameter, which is 1.25" on TRU94FR and 1.38" on TRU59FR.
  view full answer...
  
• Replacement Axle for 1956 Dutton-Lainson Trailer
  Hi Mark; it looks like you may have already sorted this out since you bought the # TRU59FR replacement spindle. Assuming this is a 2k axle that is the best option aside from replacement. You can still send me your pictures but based on the age and your description I'm 99% sure it is an old outdated spindle nothing would fit. If the axle appears to be in good shape by all means swap out the spindle, otherwise it is probably a good idea to replace it completely like you originally thought.
  view full answer...
• What Replacement Spindle Do I Need for a Dexter 69-46 Spindle?
  As far as removing your current spindle, you will need to grind/drill off the old one. One the old spindle is removed, I recommend the BT8 Spindle for 2,000-lb Trailer Axles # TRU59FR (for a 1-3/8 diameter) or the # TRU94FR (for 1-1/4 diameter). The measurement of the diameter is the stub (innermost tube on the spindle). In order to get the correct size, I recommend measuring the stub of your old spindle once it is removed. I went ahead and attached videos of both of these spindles in order...
  view full answer...
  
• How to Determine The Correct Replacement Trailer Hubs by Bearing Numbers or Spindle Size
  The best way to determine which replacement hubs you need for your trailer would be to remove one of the hubs and retrieve the bearings. Find the numbers stamped into the bearings and with those we will be able to get you the correct hubs. If you are unable to retrieve the bearing numbers, you can take measurements of the spindle. I have included a link to our spindle main page. At the top of the page is a diagram showing all of the measurements we would need to find the correct hubs...
  view full answer...
• Replacing Hubs On a 4' X 6' Carry On Trailer From 4 on 4" Lugs to 5 on 4-1/2" Lug Pattern 15" Wheels
  Your current axle on your 4' X 6' Carry on Trailer will likely have either a BT8 Spindle # TRU59FR or BTR Spindle # TRU44FR. You can determine the spindle by removing your current hub and inspecting the bearings or by measuring the spindle itself. I have included a image that shows the locations of the bearing numbers and grease seals on your current hub as well as the measurement points for spindle as well. The BT8 Spindle # TRU59FR uses Bearings # L44643 which have an inner diameter...
  view full answer...
  
• Depth Measurement For Hubs That Fit A 1" Straight Spindle
  We do have hubs available for a 1" straight spindle in part # AKIHUB-440-2-EZ-1K. This hub measures 4-1/4" deep so it will run a bit longer than the hub you are looking for. There are a total of 4 hubs that we carry for a 1" straight spindle and all 4 would be identical as far as depth. A lot of these older boat trailers use hubs that are trailer specific, and it may prove very difficult to find. We do carry replacement spindles like part # TRU59FR, if you want to change it out for a more...
  view full answer...
• Replacement Hub For BT-100 Trailer Idler Hub On a 1" Straight Spindle
  The Easy Grease Trailer Idler Hub Assembly # AKIHUB-440-2-EZ-1K will replace your current BT-100 idler hub. This hub fits your 1" straight Spindle # TRU59FR with the 4.80-8 Wheel and Tire # AM30040 and will use the Bearing Kit # BK1-100.
  view full answer...
• Replacement Hub For A 1949 Or 1950 TeeNee Boat Trailer With Short Spindles
  I have a solution for you, but as the short spindles have not been produced for some time now, there will not be a hub that will fit them properly, unfortunately. You will need to replace the spindles with the BT8 Spindle for 2,000-lb Trailer Axles # TRU59FR. If you are or know a good welder, this can be done pretty easily, but you need to make sure the cross tube connecting the two spindles has an inner diameter of 1-3/8" (typically a 1-3/4" outer diameter). Once these are on, the CE...
  view full answer...
• Replacement Bearing Kit For Idler Hub 5 On 4.5 With 1 Spindle and 1.24 Inner Diameter Grease Seal
  The measurements that you gave tell me that you have a BT8 Spindle # TRU59FR. If you wish to replace your bearings, races and grease seal you will want the Bearing Kit # BK1-100. This includes 2 Bearings # L44643, 2 Races # L44610, a Grease Seal # 34823 and a Cotter Pin # 165649. To make things easier you can replace your entire hub. Depending on your wheel size you can choose either the Idler Hub # AKIHUB-545-2-1K that has the 5 on 4-1/2" lug pattern you said you have with 10"-12"...
  view full answer...
  
• How to Find a Replacement Spindle and Hub for a 5x10 SnowBear Utility Trailer with 2000 lb Axle
  We do have spindles and hubs for 2,000 lb axles, but we first want to determine which spindle and hub will work best for you. To do this we will need additional information about your current spindles and hubs to ensure the new spindle and hub match what you currently have. Unfortunately SnowBear does not provide general spindle and hub information for their trailers. The best way to ensure you get the correct spindle and hub is by using the part numbers of your bearings and grease seal....
  view full answer...
  
• What Does a Damaged Trailer Spindle Look Like
  Yes, that spindle does look too beat up to be usable. I attached a link to this page that has all of the spindles we carry. You would need to pick out the one that matches the axle capacity on your trailer. It looks like maybe a 2,200 or 2,000 lb axle possibly like the # TRU59FR.
  view full answer...
  
• Correct Bearings for 1-3/8 Inch Spindle
  I do have the correct bearing for a 1.375" spindle like part # TRU59FR however, the L68149 bearing is not the correct bearing for this spindle. The correct bearing for the 1-3/8" spindle is the L44643 bearing like that in the Bearing Kit for 1" BT8 Spindle part # BK1-100 which is designed for 2,000 lb. axles. The Replacement Trailer Hub Bearing part # L68149 is compatible with an #84 spindle such as the Spindle # TRU24FR which is designed for use on a 3,500 lb axle. I have attached our...
  view full answer...
• Should a Spindle That is Chipping be Replaced
  Anytime that a spindle is starting to take damage you will want to replace it as that will affect the performance of your bearings and seal. In this case since that chipping is right where the seal sits (as you mentioned) that will eat at the rubber seal which will likely cause it to fail. A failed seal will leak grease and cause further damage to your spindle/hub area. From the picture you sent in it looks like you have a round BT8 spindle. For replacements we have parts # TRU94FR, #...
  view full answer...
  
• Replacement Hub Options For a Peterson Brothers Gator 417 Boat Trailer With 5 On 4-1/2" Bolt Pattern
  Based on your spindle measurements you will want to update your axle as there are no replacement hubs which will fit your current spindle. We have a couple different size axle which includes idler hubs with the 5 on 4-1/2" bolt pattern. 60" etrailer Trailer Axle with Idler Hubs # e84YR 72" Dexter Trailer Axle with Idler Hubs # 20545I-ST-72-15 You can also have 2 new Spindles # TRU59FR welded onto your axle and then be able to use the Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-2-EZ-1K...
  view full answer...
• Replacement Trailer Idler Hub With Inner Bearing 1.25" and Outer Bearing 0.75" Inner Diameters
  The only hub we carry that will fit your spindle size is the Agricultural Hub # AH15450ECOMP, as most have changed over to the more common BT8 # TRU59FR and BTR # TRU44FR. The agricultural hub is only rated for speeds up to 20mph and uses a 4 on 5" bolt pattern. You can have your spindles replaced to one of the more common sizes but this is best done at a trailer manufacturer so they can true up the ends of the spindle to ensure it is welded on straight. Otherwise if you can give me dimesnions...
  view full answer...
• Are There Trailer Hubs With 4 on 110 Bolt Pattern
  Hi Clint, There aren't actually trailer hubs with the 4 on 110 bolt pattern, as nice as that would be to match the pattern of your tires. There is a 4 on 4" which you can use if you like, the Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 # AKIHUB-440-2-1K. With this you can use the BT8 Spindle for 2,000-lb Trailer Axles # TRU59FR. I have added a link below to our entire selection of hubs as well as spindles if you wanted something different than this option.
  view full answer...
• Dimensions Of Dexter Hub Assembly For 8 to 12 Inch Wheels
  The Dexter Hub Assembly, part # 34822545BX is designed to be used with 2,000 lb axles and for 8 inch to 12 inch wheels. This assembly includes bearings, races, seal, grease cap, wheel bolts and lug nuts. I have attached a photo of the hub and have the hub length noted on the photo. The length of the hub is 4-1/4 inches and the inner diameter of the inner and outer bearings, part # L44643, that are included with the hub measure 1 inch. A spindle that is designed to work with the 34822545BX...
  view full answer...
  
• Which Spindles Will Work with the Trailer Hub Assembly for 2,000 lbs Axles
  You can use any of three spindles with the Trailer Hub Assembly - 2,000 lbs Axles - 5 on 4-1/2, item # 34822545BX. I have listed these spindles below. # TRU94FR - BT8 Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter # TRU59FR - BT8 Spindle for 2,000-lb Trailer Axles - 1-3/8" Diameter # TRU97FR - Square BT8 Spindle for 2,000-lb Trailer Axles - 1-1/2" Wide The main difference in these spindles is the mounting dimensions on the inboard end of the spindles. the bearing seal and threaded...
  view full answer...

Do you have a question about this Trailer Spindle?