What Does a Damaged Trailer Spindle Look Like

Question

Question:

Hello. The attached pictures are of the top and bottom of a spindle for boat trailer. Are the grooves on the under side too excessive? Thank you.

asked by: Adam

0

Expert Reply:

Yes, that spindle does look too beat up to be usable. I attached a link to this page that has all of the spindles we carry. You would need to pick out the one that matches the axle capacity on your trailer. It looks like maybe a 2,200 or 2,000 lb axle possibly like the # TRU59FR.

expert reply by: Jameson C

0

Damaged Spindle
(click to enlarge)

Answer 1

Based on your inner bearing being L68149 and outer bearing indicating L44649, I recommend Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles #84545UC1-EZ as long as your wheels have a 5 on 4-1/2 inch bolt pattern. This hub is designed for…

view full answer...

Answer 2

If you remove the hub and wipe away the grease on the spindle you can check to see if it is damaged. Look for an scarring, gouges, discoloration, or scoring on the spindle. If the spindle is damaged then the bearings won't ride properly and can…

view full answer...

Answer 3

For the drum what you are going to want to look at is discoloration where the pads make contact with the drum and the armature surface which is where the magnet makes contact with the inside of the drum. Discoloration means that the metal is damaged…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

What Does a Damaged Trailer Spindle Look Like

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching