See what our Experts say about this Optronics Accessories and Parts

• Recommended 2-1/2" Long Amber Clearance or Marker Light for a Boat Trailer
  Thanks for the pictures Jaime. The Peterson item # M152A is what you'll need to replace the marker light in your Shorelandr boat trailer's fender. This is an incandescent light that measures 2-1/2" wide x 1-1/4" wide. It is sold individually and has two male terminals that accept a standard 2-wire female plug. I attached a picture below so you can see the terminal connections. I know you said you preferred to avoid an LED replacement light. However, the Thinline LED Clearance and Side...
  view full answer...
• Replacement Lens Availability for Reflect-O-Lite SAE-P-P1-68
  Unfortunately we do not have any replacement lenses for your Reflect-O-Lite lights. There may be some out there somewhere but the only solution we have for you would be to replace all of your lights. If you end up wanting to do this I can help you with replacement lights but it may be worth seeing if somewhere else has replacement lenses.
  view full answer...
  
• Does Optronics Clearance Light A91RB with Base A91BOB Have Clearance for 90 Degree Mount
  Hey Jim, yes the Mounting Bracket # A91BOB with the clearance light part # A91RB would allow a right angle pigtail like the part # A46PB to fit and have enough clearance.
  view full answer...
• Do Thinline LED Clearance and Side Marker Lights Come With Bracket and Wiring
  Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The # AL91RB and # AL91AB will work with the Mounting Bracket # A91BB and then for a pigtail you can use the Right Angle 2-Wire Pigtail # A46PB. Where are you headed with your boat once you get the lights replaced on your trailer?
  view full answer...
• Replacement Parts for WESBAR 787264, 108662, and 729063
  Hey Laura, thanks for the part numbers. Wesbar's lights, connectors, and wiring harnesses have been gone for years but we do have comparable options. I have listed them below: 787264 - 3-Wire Pigtail for Optronics Trailer Lights item # A45PB 108662 - Right Angle 2-Wire Pigtail for Optronics Trailer Lights item # A46PB 729063 - Curt Wiring Harness with 4-Pole Flat Trailer Connector item # C97NR If you have any additional questions, go ahead and click on the box that says Add Comment...
  view full answer...
• Two Prong Connector To Use with TecNiq Side Marker with Reflector # TN53TR
  Hey Wade, the 2 wire connector you need to use with the TecNiq trailer taillights part # TN53TR is the part # A46PB.
  view full answer...
• What Bracket and Wire Plugs Fit The Thinline LED Trailer Clearance Light # OPT66FR?
  You will need the Bracket # A65B with either the 1-Wire # A65P or 2-Wire # A46PB for the Thinline LED Trailer Clearance Light # OPT66FR.
  view full answer...
• Replacement Grommet for Optronics
  Hey Jay! I am definitely going to need you to send me those pictures to the email address you receive this response from. Meanwhile I have listed some of the parts I think you described below along with that grommet you need: Grommet for Optronics A91, AL82, AL90, AL91, or AL191 Series Trailer Lights - Black PVC item # A91GB Replacement Pigtail - 3-Wire - 90 Degree item # 40-00-004 Right Angle 2-Wire Pigtail for Optronics Trailer Lights item # A46PB What kind of trailer do you have?
  view full answer...
• Spacing Between Two Electric Connectors On Thinline LED Clearance and Side Marker Light AL91RB
  Hello Jeff, thanks for reaching out. The two electric connectors on the Thinline LED Clearance and Side Marker Light # AL91RB are indeed 1/2" apart on center. This will work with really any standard 2-prong plug. They would all use that standard 1/2" pin spacing. For example, the Right Angle 2-Wire Pigtail for Optronics Trailer Lights # A46PB will go with it.
  view full answer...
• What Size Hole is Needed to Mount Optronics 2-1/2 Inch Side Marker Light with Reflector and Grommet
  The Optronics Sealed 2-1/2 Inch Round Trailer Clearance, Side Marker Light # MC57AB along with the Round Grommet - Floush Mount # A55GB will require you to cut a 3 inch diameter mounting hole. You will also need the Right Angle 2-Wire Pigtail Plug # A46PB to pair with the female connection on the Optronics light. I have attached video reviews of these products for you to look at.
  view full answer...
• Replacement Clearance and Side Marker Lights for a 2019 EZ Loader Tandem-Axle Boat Trailer
  Hey Cory, welcome back and thanks for the picture. That's a tough situation you're in. I went through all of our submersible lights and I do not have a suitable replacement that does not require the use of the item # A46PB pigtail. My only solution is to use the Thinline LED Clearance and Side Marker Light - Submersible item # AL91RB in red and item # AL91AB in amber. They measure 2-1/2" L × 1-3/16" W × 7/8" D. These lights work with the following mounting brackets and grommets: Mounting...
  view full answer...
• Surface Mounting Bracket For Custer LED Side Marker/Clearance Light CPL26-A
  Hi Adam! We do have another option that will fit the exact same way, but I am sad to say the Custer bracket is no longer available. The Custer LED Side Marker or Clearance Trailer Light # CPL26-A snaps into the Optronics bracket # A91CB perfectly (almost too perfectly as it took a slot screwdriver and some patience to get it out when I test fit them together). Unfortunately, it does only come in silvery chrome finished plastic, but it could very easily be rattle canned to whatever color...
  view full answer...
• Electrical Plug to Use with Optronics Trailer Clearance Light LP97CB
  Hey Greg, so the correct harness to use with the light part # LP97CB is the part # A46PB.
  view full answer...
• Replacement Clear Marker Light For a Glo-Brite 9500c-88
  While we do not carry the Glo-Brite 9500c-88 you currently have, we do have a light that will work as a replacement for you. From the information I could find on your Glo-Brite 9500c-88, it measures 2" in diameter. For the clear light, you would want the Optronics Miro-Flex LED Utility Light # UCL50CB. This light measures 2" in diameter and should fit in your current grommet. You would also need the 2-Wire Pigtail for Optronics Trailer Lights # A46PB. If you want to replace the grommet...
  view full answer...
• LED Clearance Light Recommendation for Sundowner Horse Trailer
  What you have on your horse trailer is a pretty common clearance light that we do offer in red and amber as an LED. For the red you'd want the part # AL91RB and for amber part # AL91AB. You'll also need the grommet part # A91GB and the right angle pigtail part # A46PB and you'd be set.
  view full answer...
  
• Availability Of White Replacement Fender For 2003 Shoreland'r Trailer W/ ST205/75R15 Tires
  I sure can! Based on the picture you provided the correct replacement fender for your trailer is going to be the Plastic, Single-Axle Trailer Fender w/ Top and Side Steps - White - 13" to 15" # PF11X35W which will work perfectly with the ST205/75R15 tires on your 2003 Shoreland'r Trailer and closely resembles your current fender. You will also need mounting brackets # PF1135-BKT-2 to mount the fender to your trailer. In regards to the clearance lights I will need to know the length...
  view full answer...
  
• Replacement Amber Clearance Light for Dutchman Kodiak
  The lenses on clearance lights are not generally removable as they are often "sonically sealed" such as the Optronics Trailer Clearance or Side Marker Light # MC57AB; this means they are submersible. Instead of buying a light and taking the lens off I strongly recommend an LED Trailer Clearance or Side Marker Light w/ Reflex Reflector # MCL59AB for your Dutchman trailer because an LED is a far better, much longer lasting option. You only need to make sure your existing lights have the...
  view full answer...
  
• Replacement Clearance Taillight Solution for EZ Loader 250-032130
  I looked up your EZ Loader part number and it appears to be the same design as the part # AL91AB which for the matching grommet you'd then need the part # A91GB. You'll also need the wiring harness # A46PB.
  view full answer...
• Replacement Trailer Lighting and Wiring Harness for a Big Tex 70PL Utility Trailer
  While I cannot lookup exact part numbers for your Big Tex 70 PL utility trailer I was able to create a list of parts based off of images I could find online. You will want to compare the measurements for your lights against the ones of the lights I have listed. 2" Amber Marker Light # MCL57AB 2" Red Marker Light # MCL55RB 2" Rubber Grommet # A54GB 2-Wire Pigtail # A46PB 6-1/2" x 2-5/16" Tail Lights # TLL12RK The tail lights include the grommets and wire pigtails. I recommend using the...
  view full answer...
• Replacement Trailer Clearance Light for PM150
  The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part # AL91RB. For a replacement harness that would plug into this you'd need the part # A46PB and then for a grmmet part # A91GB for a flush mount or part # A91BOB for a bracket for surface mount.
  view full answer...
  
• What Size Hole Needs to be Drilled to Install 2-1/2 inch Optronics Clearance Light MC57RB
  The Sealed, 2-1/2" Round Trailer Clearance, Side Marker Light with Reflector # MC57RB requires the use of a the Grommet part # A55GB to install. This grommet will require a 3 inch hole to be drilled. For a pigtail harness you would need the part # A46PB as well.
  view full answer...
• Trailer Clearance Light Recommendation to Fit 2-3/4 inch Diameter Hole
  For a grommet that fits the diameter hole of 2-3/4 inches we have the part # A57GB which fits lights that are 2-1/2 inches in diameter like the Miro-Flex LED Trailer Clearance or Side Marker Light # MCL51RB. You'd need these two things plus a wiring pigtail part # A46PB and you'd be set.
  view full answer...
• Procedure to Re-Install Trailer Side Marker Lights
  Installation methods will vary depending on the nature of the particular light you are using. We offer a wide range of clearance/marker lights (all can be seen on the link provided) and these include flange-, flush- and surface-mount types. You can use the filters in the left-hand margin to narrow the product results shown to just those light that meet your requirements. You can sort by lens color, bulb type, mounting type, brand and dimensions. For example, in 2-1/2- x 1-1/2-inch size...
  view full answer...
• Replacement Taillights, Wiring and 7-Way Connector for Car Hauler
  To fit the round 4-1/2 inch holes on your trailer for the rear brake lights you could use the # STL42RB as this will fit in that hole. For a pigtail harness you would also need # A45PB. For the side clearance lights you would need to enlarge the holes to 3 inch in diameter, use the # A55GB as a grommet and then use # MCL59AB for the lights and # A46PB as a wiring harness. For a replacement 7-way with 8 feet of wire for running new wire everywhere you would want the part # H20046. You...
  view full answer...
  

Do you have a question about this Accessories and Part?