Depth Measurement For Hubs That Fit A 1" Straight Spindle
Updated 07/12/2023 | Published 07/11/2023
Products Featured in This Question
Question:
I am looking for a trailer hub for a 1inch diameter spindle that is 3 3/4 inches long from the inner bearing landing to the end of the threads. It is for an old Sterling boat trailer that only has the wheel with casalated nut and cotter pin.
asked by: Doug R
Expert Reply:
We do have hubs available for a 1" straight spindle in part # AKIHUB-440-2-EZ-1K. This hub measures 4-1/4" deep so it will run a bit longer than the hub you are looking for. There are a total of 4 hubs that we carry for a 1" straight spindle and all 4 would be identical as far as depth. A lot of these older boat trailers use hubs that are trailer specific, and it may prove very difficult to find.
We do carry replacement spindles like part # TRU59FR, if you want to change it out for a more "standard" spindle. You can use that with the hubs # AKIHUB-440-2-G-EZ-1K. The spindles can be tricky to install and you would want to take your trailer to a professional welder or axle shop.
We also have replacement axles if that is something you want to look into. I would want to confirm the length of the current axle, but something like part # e25GR would be a potential replacement. This axle is 60" long from hub face to hub face and is rated for 2,000 lbs.
I can also provide the cotter pin # 165649 and castle nut # 165686 if you are in need.
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44649 / L44649
- Marine Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 8 Inch Wheel
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- etrailer
more information >
Continue Researching
- Search Results: 2 5/16 trailer tongue
- Search Results: trailer hitch lock
- Search Results: 2 5/16 balls
- Search Results: 2 5/16 coupler
- Search Results: trailer hubs and drums
- Search Results: bearing buddy
- Search Results: bearing buddy caps
- Video: Review of Kenda Trailer Tires and Wheels - Tire with Wheel - KE44WV
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Trailer Spindle Nut 1"
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased - Threaded
- Shop: B&W Tow & Stow Pintle Hook with 2" and 2-5/16" Balls - 2" Hitch - 10K/16K
- Q&A: Spindle Compatible With Trailer Idler Hub Assembly AKIHUB-440-2-1K
- Video: Feature Review CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles
- Shop: Kenda Karrier KR53 ST225/75R15 Radial Trailer Tire with 15" Silver Mod Wheel - 6 on 5-1/2
- Shop: Washer For 1" Spindle
- Shop: Trimax Receiver Lock for 2" and 2-1/2" Hitches - 3-1/2" Span - Black
- Q&A: Bearing Buddy Dust Covers for Bearing Buddy with 2.125" Outer Diameter
- Q&A: Should There Be a Washer on Trailer Spindle Between Spindle Nut and Outer Bearing
- Q&A: Replacement Hub Recommendation for Trailer with .99 inch Bearing ID Surface Dimension
- Q&A: Hub length of CE Smith Trailer 13110 and 13100
- Article: Rooftop Cargo Carriers
- Q&A: How To Determine the Weight Capacity For a Trailer Axle
- Q&A: Replacement Hub for Spindle With 1" Inner Diameter Bearings
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: How to Determine Tire/Wheel Diameter
- Video: Identification Light Bar for Trailers over 80" Wide: The Breakdown
- Video: Trailer Idler Hub Assembly for 2K Axles Review
- Video: DIY Installation for the etrailer Galvanized Trailer Idler Hub Assembly for 2,000-lb Axles