Are the TruRyde Spindle # TRU59FR and etrailer Idler Hub Assembly # AKIHUB-545-2-2K Compatible
Published 09/01/2017
Products Featured in This Question
Question:
Is spindle TRU59FR compatible with this hub?
asked by: Doyle W
Helpful Expert Reply:
The TruRyde Spindle # TRU94FR and our Trailer Idler Hub Assembly # AKIHUB-545-2-2K are not compatible, but you could use the TruRyde EZ Lube Spindle # TRU44FR instead as it has the correct spindle measurements.
For a hub that will work with the TruRyde Spindle # TRU94FR you can use part # AKIHUB-545-2-1K.
To determine if a hub is compatible with a specific spindle you will need to make sure that the inner diameters of the Inner Bearing, Outer Bearing, and Grease Seal of the hub matches up with the corresponding locations on the spindle. These locations are B, C, and D on the attached picture.
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Idler Hub
- Pre-Greased
- Standard
- L44649 / L44649
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Continue Researching
- Search Results: camper jacks
- Search Results: winch stand
- Search Results: jacks and jack stands
- Search Results: lock n roll straight tongue trailer coupler
- Search Results: trailer hitch lock
- Search Results: lock n roll a~frame trailer coupler
- Search Results: trailer axles
- Shop: Hydrastar Adjustable Winch Stand Assembly for Trailer Tongue - 3" x 4" Post
- Shop: Lippert Trailer Brake Drum for 10K Axles - 12-1/4" x 3-3/8"
- Shop: Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel - Qty 2
- Shop: CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" - Qty 4
- Shop: CE Smith Carpeted Bunk Boards for Boat Trailers - 7' Long - 1 Pair
- Video: How to Install Your Curt Friction Sway Control
- Shop: BT8 Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter
- Q&A: BLTL-20 Coupler Lock Fit a Bulldog Coupler Heavy-Duty Cast Head Coupler w/ Wedge Latch
- Shop: BOLT brand vehicle and hitch locks
- Video: An In-Depth Look at the CE Smith Carpeted Johnboat Bunk Board for Boat Trailers
- Video: Setting Up Your etrailer Trailer Idler Hub Assembly for 2K Axles
- Q&A: Looking for Replacement 5 Lug Hub with Bearings L44649 Pre Greased
- Q&A: Depth Measurement For Hubs That Fit A 1" Straight Spindle
- Q&A: Recommended Hub W/ Integrated Drums for a BT8 Spindle
- Q&A: Do You Have a Replacement Bearing Kit for a Lippert 8,000 lbs Axle?
- Video: Review of etrailer Trailer Fenders - Black Plastic Single Axle 3 Step 12 Inch Wheel - HP33RR
- Q&A: Replacement Wheels And Hubs For A Triton LTWCI Personal Watercraft Trailer
- Video: Review of ESCO Trailer Breakaway Kit - ES34FR
- Shop: Gooseneck Hitch
- Shop: Fifth Wheel Hitch
- Shop: Trailer Hitch
- Shop: Headache Rack
Doyle W.
9/1/2017
Is spindle TRU59FR compatible with this hub?