See what our Experts say about this etrailer Trailer Bearings Races Seals Caps

• Replacement Disc Brake Rotor/Hub For a 1990 Ranger Trail Boat Trailer
  The Dexter 10" Hub-and-Rotor Assembly # K08-435-05 is designed to fit a 3,500LB trailer axle with the Inner Bearing # L68149, Outer Bearing # L44649 and Grease Seal # RG06-050. To confirm if this is what matches the axle on your 1990 Ranger Trail Boat Trailer, you will need to inspect your current hub for the bearing and seal information. If you are unable to find the information stamped on the bearings and seals you can measure your spindle with a Digital Caliper # PTW80157. Once you have...
  view full answer...
  
• Replacement Brake Assembly and Grease Seal for AL-KO T44 Axle
  For your AL-KO T44 axles, the brake assemblies you need are the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4.4K # K23-478-479 or the manual adjust # K23-462-463-00 along with spoon adjuster # W80630. The grease seal you want is AL-KO part 568861 which is the Grease Seal - Double Lip - ID 1.719" / OD 2.565" # RG06-050 for a set of 2 seals.
  view full answer...
  
• Replacement Bearings and Seals for Lippert 4,400 Lb Axle
  The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part # BK2-100 or just the Grease Seal part # RG06-050.
  view full answer...
• Wheel Bearings and Grease Seal for 2023 Keystone Cougar 23MLE
  Well, Dexter is normally really helpful but in this case not so much. From what they sent back you have a # L68149 inner and outer bearing. I've never heard of that before and really don't believe you have a straight spindle. Based on the fact that you also have a 10-19 grease seal # RG06-050 I feel like the outer bearing is actually # L44649. This would mean you can use the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle # BK2-100. I hate to say it but...
  view full answer...
• Timbren Axle-Less Suspension System Compatibility with Aluminum I-Beam Trailer Frame
  The Timbren Heavy-Duty Axle-Less Trailer Suspension - 4" Lift Spindle - Off-Road Tires - 3,500 lbs # ASR35HDS02 is compatible with I-beam frames and in tandem axle configuration. Due to the Aluminum frame, I recommend putting a thin rubber pad between the steel mount and the aluminum I-beam. The powder coat on the steel should keep the two dissimilar metals from galvanic corrosion, but a thin rubber pad would drastically increase this safety. Zinc plated hardware will work well with...
  view full answer...
  
• Availability of Bearing Kit for Dexter 4,400 lb Trailer Axle
  We do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following: Bearings # L68149 and # LM67048 Races # L68111 and # LM67010 Grease Seals # RG06-050
  view full answer...
• Replacement Brake Assemblies and Grease Seal for 3,500 lb Trailer Axle
  Hey Phillip, since we know you have 3,500 lb axles we can help but it's not based on the VIN. Since we don't know what brake assembly brand you have on your trailer but we do know capacity the correct replacement assemblies are the part # AKEBRK-35-SA. It's oftentimes more cost effective to just replace the assemblies instead of the individual components plus it's a lot harder to find the parts. Then for a grease seal you'd want the part # RG06-050.
  view full answer...
• Need Bearing Kit For Lippert 3,500 lb Axle On 2021 Forest River Grey Wolf 23DBH
  Hello, and thanks for providing all of that information for your axle. I had my contact at Lippert run the item number and serial number. Your axle is a standard 3,500 lb axle and it used the standard bearing and seal sizing. Our bearing kit # BK2-100 is exactly what you will need to repack everything. This comes with both bearings, races, seal, tang washer and cotter pin. Use one kit per hub. I have included all of the bearing info for your trailer below. Let me know if you need anything...
  view full answer...
• Replacement Grease Seal for Lippert 4400 lb Axle
  The grease seals for the hubs on Lippert's 4,400 lb trailer axles are the same grease seals used on 3,500 lb axles, and you can get either a pair of seals or just one seal, depending on how many you are looking for: 2: Grease Seals # RG06-050 1: Grease Seal # 58846
  view full answer...
• Replacement Grease Seal for Trailer Hub that is Marked 171255
  The seal we offer part # RG06-050 that you mentioned cross references as the same thing as a Transcom part 171255TB. It would be the exact same as what you have/need.
  view full answer...
• Replacement Grease Seal for 3,500 lb Dexter Axle on Forest River Trailer
  Thank you for reaching out! What is the weight rating of your axle? Unless it's a really old axle I should be able to make a recommendation based off of that. The Dexter Axle part number you sent in normally doesn't pull anything up on their system (although I'm not sure why) so I would need the serial number and/or a photo of the sticker in the middle of the axle for me to get any info from Dexter Axle.
  view full answer...
  
• Replacement Hub with Inner Bearing LM48548 and Outer Bearing L44649
  I may have a solution for you, but we do not have any hubs that are compatible with the # LM48548 inner bearing that you've currently got in your hubs. Additionally the # 84556UC3 is not going to fit your spindle because the # L68149 outer bearing it contains is going to be slightly too big. You could continue to use your old hubs and simply replace the bearings with the # LM48548 and # L44649. For the races, you'll want # Replacement Race for LM48548 Bearing # LM48510 and # L44610 and...
  view full answer...
• Wire Size Butt Connectors is Needed to Connect Wiring for Electric Trailer Brakes
  Electric brakes, like part # 23-26-27, use 16 gauge wiring. However, we generally recommend using 10 gauge, like part # 10-2-1, to connect to the brakes because of how far the wiring generally has to be run. So you need to use butt connectors large enough for the 10 gauge wire, like part # DW05745-5. They'll still be able to be crimped down onto the smaller 16 gauge as well, especially since they're heat shrink. Between the two grease seals, parts # 58846 and # RG06-050, we prefer our...
  view full answer...
• Double-Lip Grease Seal to Replace Hayes Seal 09103305 or Al-Ko Seal 568861
  Tru-Ryde double-lip grease seal kit # RG06-050 will work as a replacement for Hayes seal 09103305 or Al-Ko seal 568861 since these parts all share the same inner diameter of 1.719-inches and the same outer diameter of 2.565-inches. Part # RG06-050 is a set of 2 seals.
  view full answer...
• Replacement Grease Seals For TRP GS-1719DL
  From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you need are part # RG06-050. There are 2 seals in the package. When replacing any components for your hub, you will want to make sure you either get the numbers for the parts or take precise measurements with a digital caliper. I have attached...
  view full answer...
  
• Replacement U-Bolt and Grease Seal for Dexter 3,500 lb Trailer Axle
  If you can get me the axle capacity or even just the diameter of it I would be able to tell you what seal and u-bolts you'd need.
  view full answer...
• What are the Trailer Suspension Parts to Upgrade the Suspension on a 2021 GD Imagine 2600 RB?
  Hello Ron, I am very sorry to hear that your frame is bending, but I am happy to hear that the people at Lippert are getting you taken care of! Upgrading the suspension is always a great idea! In my search I see that the 2021 GD Imagine 2600 RB is equipped with 2.25" shackles. Looks like you already found the right shackle kit # MR46ZR. This kit is great, it will come with new shackles, wet bolts with the zerk fittings making them easy to lube, lock nuts, and even the bronze bushings....
  view full answer...
• What Electric Brakes and Grease Seals do I Need for My 2022 Discovery Rover ET ?
  Hello Sean, Thanks so much for getting that picture to me. It is most helpful. Your axles are rated for 3,500 pounds, so you will want our etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K # AKEBRK-35-SA (or the TruRyde you were looking at # TRU36FR ). These are self adjusting brakes, so one less maintenance thing you have to worry about. If you are looking to repack your bearing when you swap your brakes out, make sure to grab some LubriMatic...
  view full answer...
• Replacement Grease Seal for 3.5K Dexter Axle on Forest River Salem Hemisphere 22RKHL
  Hey Jeff, thanks for all of the information! For a 3,500 lb Dexter Axle you need the part # 58846, which is also available in a kit of 2 as part # RG06-050. Is there anything else you're needing to swap out or update on your trailer?
  view full answer...
• Replacement Bearing Kit For a 1999 Dutchmen Model 801D Pop Up Camping Trailer
  I do believe that the Bearing Kit # BK2-100 is the correct kit for your 1999 Dutchmen 801D Pop up camper. You will want to verify that this is the correct kit by comparing to your current bearings or spindle. Inner Bearing # L68149 (1.378"ID) Outer Bearing # L44649 (1.063"ID) Inner Race # L68111 (2.361"OD) Outer Race # L44610 (1.980"OD) Grease Seals # RG06-050 (1.719"ID, 2.565"OD)
  view full answer...
  
• Finding the Most Cost-Effective Solution to Add Brakes to Trailer
  Hydraulic disc brakes will be the most cost-effective solution for you. In order to add those you will need to know your axle's weight capacity. I recommend going with a hub and rotor disc brake kit such as the Kodiak # K2HR35D. To add a hub and roter you will need to take apart your current hubs and find the bearing numbers. The # K2HR35D, for example, use inner bearing # L68149 and outer bearing # L44649 and yours would need to match. The hubs in this brake kit also have a 5 on 4-1/2...
  view full answer...
• Grease Seals for 2019 Coachmen Apex 288BHS with Dexter 3.5K Axles
  Hey Rod! Yes, the Grease Seal # RG06-050 is exactly what you need for the Dexter 3,500 lb axles on your Coachmen. You'll need one kit per axle (so, 2 kits) as the seals go on the part of the hub closest to the axle tube. What kind of experience do you have repacking bearings so far?
  view full answer...
• Replacement Bearings for 2019 Grand Design Imagine 2670MK
  Hello again Dave, can you email me a picture of your axle tag? We already know it is a 4,400 lb axle but those bearing combinations can vary depending on the spindle they used. If you respond to the email with the link for this page it will come to me directly.
  view full answer...
• Can 1/4 inch Thick Trailer Hub Grease Seal be Replaced with a 1/2 inch Thick Seal
  Hey Zachary, are you sure you need the seal to be that thin? Normally variances in seal thicknesses doesn't really affect anything and replacing a thinner seal with a thicker one doesn't cause any issues. If that's case our part # 58846 would fit and work great.
  view full answer...

Do you have a question about this Trailer Bearings Races Seals Cap?