See what our Experts say about this Timken Trailer Bearings Races Seals Caps

• Availability of USA Made Bearing Kit for 3,500 lb Trailer Axle
  Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part # TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?
  view full answer...
• Determining Bearings For 2021 Rice Car Trailer
  Hello Jeffrey, While I'm sure we have a bearing kit for your car trailer, we don't have any way of knowing off-hand or cross-referencing what bearings you need. You mentioned you have them out, so you should be able to see the part number stamped directly on them, and you can use that as a guide for what to get. For example, if you have bearings L68149 and L44649 you would use the 3,500 lb Timken Bearing Kit # TMK52VR I have added a link below to our entire selection of bearing kits...
  view full answer...
• Replacement Bearing Kit for a 2021 Jayco Jay Flight SLX 195RB
  Hey Scott, thanks for reaching out! The Timken Bearing Kit # TMK92VR you're looking at is for a 7K axle, and according to my research your 2021 Jayco Jay Flight SLX 195RB should be equipped with a 3.5K axle so we need to get you a different kit. For a 3.5K axle the Timken Bearing Kit # TMK52VR uses the standard bearings and seal, but it always helps to double check everything. This kit comes with the following parts: - Inner bearing L68149 - Outer bearing L44649 - Grease seal with...
  view full answer...
• Who Makes The Best Quality Trailer Bearings?
  Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 # TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I have seen. That said, As long as you do regular maintenance, they should last a good long time. The only downside to Terran Industries specifically is the Mobilgrease XHP 222 grease they use. It can be a bit hard to find and we have heard it does...
  view full answer...
• Replacement Bearings and Seals for 2021 Grand Design Imagine 22MLE XLS
  Hey Joseph! That is a 3,500 lb Lippert axle so you can use the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle # BK2-100. If you prefer a Timken kit made in the USA the # TMK52VR is also available. Both come with everything you need for replacement. Any big trips coming up with the Imagine once you swap out your bearings?
  view full answer...
• What Bearing Kit Will Work With A 3,500 lb Terran Axle?
  Hello Daniel, thanks for reaching out. The Timken Bearing Kit # TMK52VR uses the standard 3,500 lb bearing sizes so it SHOULD fit your 3.5K Terran axle. The only way to absolutely confirm this will be to pull a hub and check/measure the bearings. The Terran brand axles are not common, so we do not have any specific info on their bearing sizing. As long as the axle was made within the last 20 years or so it should use the same standard bearing sizes, but please do confirm this.
  view full answer...
• Recommended Timken Bearing Kit for a 3,500 lbs Axle w/a #84 Spindle
  Thanks for the information Ryan. The Timken Bearing Kit item # TMK52VR is the correct one for your boat trailer. It includes inner and outer bearings and races, seal, cotter pin, and EZ lube spindle washer. This kit is sold per hub. For a grease cap with a 1.98" Outer Diameter on a boat trailer, I recommend the Bearing Buddy Bearing Protectors item # BB1980A-SS, which are made in the USA. These are capable of being completely submerged and will keep water and dirt out of your hubs and...
  view full answer...
• Replacement Hubs and Brakes for 2022 Forest River Flagstaff MAC 425M
  Hey Brent, welcome back! For replacement brakes you need the Dexter Nev-R-Adjust Electric Trailer Brakes # 23-468-469. You can also use our etrailer Electric Trailer Brakes # AKEBRK-35-SA if you want to save some money. For the hubs I'm assuming you have a 5 on 4-1/2 bolt pattern. For a Dexter replacement you need # 84546UC3-EZ. If you want to use our brand we have the # AKHD-545-35-EZ-K as well. Both of these are pre-greased and the bearings won't be made in the USA (China or similar)....
  view full answer...
• Replacement Bearings and Grease Seal for Lippert Axle LCI35-SB-67.62-53.0-NOSP-US-L-545-7213
  Hey Ryan! I sent that information to Lippert and despite the weight rating of 2,200 lbs it has a 3,500 lb axle spindle. I thought that was the case since LCI35 indicates 3,500 lbs but usually the axle rating isn't that much lower. Based on this information the correct replacement bearings are the # BK2-100 or if you want the Timken version # TMK52VR. What kind of trailer do you have?
  view full answer...
• Looking For Bearing Kit For 2014 Arising 6x12 Enclosed Trailer
  Hey James, thanks for reaching out. We certainly should have a bearing kit for your enclosed trailer, but there is no way for me to look up a year and model of trailer to know exactly what bearings you will need. Even if I had your VIN, trailer manufacturers just do not make this kind of information available online. Your best option here will be for you to pull a hub and remove the bearings. Each bearing will have a number stamped on the edge, or your can measure the ID with a caliper....
  view full answer...
• Difference Between etrailer and Timken Bearing Kit
  Hi Tony; the # BK2-100 and # TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.
  view full answer...
• Replacement Bearing Kit for a 2022 Grand Design Transcend Xplor 265BH
  Hey Jason, thanks for reaching out! Your 2022 Grand Design Transcend Xplor 265BH either has 3,500 lb axles or 4,400 lb axles. Both are listed out on the Grand Design website so you'll just need to check out the tags in the middle of your axles to verify which weight rating you have. For 3,500 lb axles use the Timken Bearing Kit # TMK52VR, and for 4,400 lb axles use the Dexter Bearing Kit # DX86ER. What weight rating do you have listed on your axles?
  view full answer...
• Bearing Kit Recommendation for 2023 Aliner Ranger 12
  Hey Jeff, since we know your 2023 Aliner Ranger 12 has 3,500 lb axle the correct bearing kit would be the part # BK2-100. This comes with the needed bearings, a new seal, tang washer, and a cotter pin so if you were to every have a problem you'd have everything you'd possibly need. Have you had bearings fail while towing before?
  view full answer...
• Replacement Bearing Kit for a Dexter 4,400 lb Hub
  Hey Robert, thanks for reaching out! To replace the bearings and seal for your Dexter 4,400 lb axle you can either use out Bearing Kit # BK2-100 or the Timken Kit # TMK52VR. The 4,400 lb hubs use the same bearings and seal as the 3,500 lb axles which is why these work. Let me know if you have any other questions or need to replace other parts! I've attached an installation video of this bearing kit for you to reference.
  view full answer...
• Looking for Replacement Bearing Kit for 2022 Imagine 2400 BH
  Hey Mark, since we know your 2022 Imagine 2400BH trailer has 3,500 lb axles the correct bearing kit would be the part # TMK52VR. Bearing replacements are all based on the axle capacity of the trailer. Are you looking to have a spare set on hand or do you have a damaged bearing setup currently?
  view full answer...
• Replacement Bearing Kit for a Jayco Jay Flight w/ 3,500 lbs Axles
  Hey Tim, thanks for the information. Since your Jayco Jay Flight has 3,500 lbs axles you'll need the Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle item # TMK52VR. This kit includes a 010-019-00 seal, along with the inner/outer bearings, races, cotter pin, and spindle washer. You'll need one kit per hub.
  view full answer...
• Timken Bearing Kit for Tie Down Engineering Hub 11033L
  Hey Aaron, the correct Timken bearing kit you need for your 3,500 lb axle (based on your bearing numbers) would be the part # TMK52VR. Now with that said a grease seal and an oil seal are different and we don't have an oil seal that matches the dimensions you need so you would need to go to grease or source the seal separately from somewhere else. Do you have oil currently?
  view full answer...
• What Bearing Kit Does 2017 Trailstar Pontoon Trailer Use
  Hey Mike, it would be really odd if your other axle used a different bearing kit so I would feel very confident that if the one axle took the part # TMK52VR the other would too.
  view full answer...
• Where are Timkin Bearings Made?
  Hey Randy. Timken Bearings like the Kit for Lippert, Dexter, and AL-KO Axles item # TMK52VR are made in the USA and Mexico. They don't list what's made where just that all of their products are made to the same specifications. The item # TMK52VR will replace one hubs worth of bearings, races, and seals on a 3,500 lbs axle with a #84 Spindle.
  view full answer...
• Bearing Kit for 2006 Weekend Warrior FK1900
  Hey Casey, since we know that your 2006 Weekend Warrior FK1900 has 3,500 lb axles the correct Timken bearing kit you need is the part # TMK52VR.
  view full answer...
• Timken Bearing Kit for Lipper 3,500 lb Axles
  Hi Daniel; the correct Timken bearing kit for your 3,500 lb Lippert axles is the # TMK52VR. The kit comes with the bearings, races, grease seal, cotter pin. and an EZ lube spindle washer.
  view full answer...
• Is the BK2-100 Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles Made By Timken?
  No, it is not Rob, but we do have one that is. The Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles item # TMK52VR also fits 3,500 lbs capacity axles with a #84 Spindle. The item # TMK52VR kit includes Timken inner and outer bearings item # L68149 and item # L44649, races and seal. It also includes a cotter pin and spindle washer. What kind of trailer do you have?
  view full answer...
• Replacement Bearings, Seals, Hubs For 2021 Riverside Retro 135 With 3,500 lb Axle
  Hey Rob; thanks for the photos and it was actually the one with the hub number that did it. That's a BD 545 which is an AxleTek 3,500 lb hub and drum like the Trailer Hub and Drum Assembly # AKHD-545-35-K. The 35 on the axle sticker was a good indicator it was a 3,500 lb axle, but the hub number verified it. So you can use that hub and drum, and for a bearing kit use Hub Bearing Kit # BK2-100 or for Timken parts the Timken Bearing Kit # TMK52VR. Both kits come with the bearings, races,...
  view full answer...
• Replacement Bearing Kit, Brakes and Hubs For a Lippert LCI35 Axle On Pop Up Camper
  Thank you for providing your axle tag and the tag for the brakes on your pop up camper Hector. You are going to need the Bearing Kit # BK2-100 or Timken Bearing Kit # TMK52VR should you want the higher quality bearings. Each kit is for one hub so you will need to order 2 for your axle. Should you need to replace your brakes I recommend upgrading to the Self-Adjusting # AKEBRK-35-SA which includes both the left and right assemblies for one axle. We do have the Shoe and Lining Kit # AKBRKR-S-10...
  view full answer...