Double-Lip Grease Seal to Replace Hayes Seal 09103305 or Al-Ko Seal 568861

Question

Question:

Looking for a double lipped grease seal, Hayes part no. 09103305 or al-ko part no 568861

asked by: Mike

0

Expert Reply:

Tru-Ryde double-lip grease seal kit # RG06-050 will work as a replacement for Hayes seal 09103305 or Al-Ko seal 568861 since these parts all share the same inner diameter of 1.719-inches and the same outer diameter of 2.565-inches.

Part # RG06-050 is a set of 2 seals.

expert reply by: Adam R

0

Bill G.

8/2/2020

Looking for Hub assembly and brakes for an AL-KO 4,400lb axle. I'm finding that this axle was short lived, and everything i'm looking up keeps throwing me the 3,500lb axle. my inner bearing is L68149, and the outer is LM67048. Grease seal 568861. Any help or explanation on this is greatly appreciated.

Reply

Chris R.

8/11/2020

I really wish I had some better news but we don't have a hub assembly that will fit your existing spindles. It sounds like this is going to be really hard to find, so your best option may honestly be with a whole new axle that features a more standard spindle size (so replacement hubs are readily available). I've linked our full selection of trailer axles below.

Helpful Links

dept-pg-trailer_axles.aspx

Reply

Bill G.

8/12/2020

@ChrisR Wow! This blows me away that no one is making these hub/drums any more. I've been able to source everything except those.

Reply

Rick B.

12/26/2020

@BillG Can you tell me if you ever found replacement hub/brake assembly for your axle? I have AL-KO 3500lb axles, but with the 12” brake assemblies that are usually found on the 5200 and up axles. I would really like to avoid having to install a whole new axle - my trailer has three.

Reply

Answer 1

Triple-lip grease seals have been around for a while, and you're not going to notice a benefit with them over the double-lipped Grease Seals #RG06-050. We do not have triple lip seals, and they're honestly just not necessary.

view full answer...

Answer 2

For 3,500 pound axle U-bolt kits like the Redline #APUBR-1 that use 1/2 inch hex nuts you will want to torque them down somewhere between 45 and 70 foot pounds. I have attached a great article on trailer suspension that includes this info along with…

view full answer...

Answer 3

To replace your GloBrite 126 marker lights you can use the #MC44RB. These lights are 2-wire incandescent lights measuring 4" long by 1-1/2" wide (same as your existing marker lights) and will work great for your trailer.

view full answer...

Answer 4

It looks like the Glo Brite Red 410 is a red side marker lamp. It seems like it's a skinny rectangle shape. We have an LED that resembles the Glo Brite Red 410 #MCL82RB. It's LED so it will last a LONG time! Waterproof too! This is the…

view full answer...

Answer 5

The brake assemblies that I recommend to replace your AL-KO brakes are #AKEBRK-35R and #AKEBRK-35L. Theses are the brake assemblies for both the left and right sides of the axle. I like these brake assemblies over the others we carry for two reasons,…

view full answer...

Answer 6

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern so for a grease seal you'd want the part #RG06-050.

view full answer...

Answer 7

The hubs used by the Dexter 4400 lb axle are 3500 lb hubs that have had their weight capacity upgraded by using a LM67048 outer wheel bearing. A 4400 hub like the #8-407-5UC3-EZ would use the same #58846 grease seal as a 3500 lb hub would. Long story…

view full answer...

Answer 8

It took a bit of cross-referencing, but I found that the 10-10 grease seal, part #RG06-090 is the correct replacement for the Al-KO 568862 seals. You can confirm this by checking the ID of the hub bore where the seal would sit. The ID should be about…

view full answer...

Answer 9

Yes, the Dexter E-Z Lube Axles still require cleaning and repacking of the bearings every 12 months or 12,000 miles. The zerk fittings on the end of the spindle are to add new grease in between maintenance intervals but they are not designed to…

view full answer...

Answer 10

It sounds like the remains of a double lip seal. Was it like a rubber o-ring with a metal spring around it? You are going to have to replace the seal so I would just disregard the sleeve. It would go on the outside of the rubber lip though. I…

view full answer...

Answer 11

The TruRyde double lip grease seal set you referenced, part #RG06-050, is indeed the correct grease seal for use on a number 84 spindle with inner bearing #L68149 and outer bearing #L44649. The reference numbers you gave are the seal part numbers…

view full answer...

Answer 12

The best way to find the correct replacement hub is to obtain the reference numbers from the inner and outer wheel bearing. I've provided a photo showing where to find the reference number on the bearing. The inner bearing would most likely be a…

view full answer...

Double-Lip Grease Seal to Replace Hayes Seal 09103305 or Al-Ko Seal 568861

Product Page this Question was Asked From

Continue Researching