Replacement Disc Brake Rotor/Hub For a 1990 Ranger Trail Boat Trailer
Updated 07/10/2024 | Published 04/23/2022
Products Featured in This Question
Question:
I have a 1990 Ranger Trail Trailer That Has Disc Brakes. Will This Part Fit My Ranger Trailer Spindles ?
asked by: Michael K
Expert Reply:
The Dexter 10" Hub-and-Rotor Assembly # K08-435-05 is designed to fit a 3,500LB trailer axle with the Inner Bearing # L68149, Outer Bearing # L44649 and Grease Seal # RG06-050. To confirm if this is what matches the axle on your 1990 Ranger Trail Boat Trailer, you will need to inspect your current hub for the bearing and seal information. If you are unable to find the information stamped on the bearings and seals you can measure your spindle with a Digital Caliper # PTW80157. Once you have the measurements for these, let me know and I can confirm the correct parts needed.
(click to enlarge)
Product Page this Question was Asked From
Dexter 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 3,500 lbs
- Trailer Hubs and Drums
- Hub with Rotor
- Standard
- L68149 / L44649
- Marine Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: trailer brakes
- Shop: Dexter 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 3,500 lbs
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 4.4K
- Video: Dexter 10" Hub-and-Rotor Assembly: The Breakdown
- Shop: Dexter 9-3/4" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 4,200 lbs
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Search Results: lucas marine grease
- Search Results: trailer bearings races seals caps
- Search Results: l68149
- Shop: Loadstar ST205/75D14 Bias Trailer Tire with 14" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Q&A: Availability of Bearing Kit for Dexter 4,400 lb Trailer Axle
- Q&A: Are There Pre-Greased Versions Of The Dexter 008-435-05 Hub/Rotor
- Video: What to Know About the Grease Seal
- Video: Review of etrailer Trailer Bearings Races Seals Caps - Bearing Kit - BK1-150
- Video: All About the Grease Seal
- Search Results: vortex cap
- Q&A: How To Easily Grease Trailer Hub Without EZ Lube Spindle
- Search Results: bearings
- Search Results: 44649
- Video: Review of the Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Q&A: Replacement Bearing Kit for Pop-Up Camper
- Q&A: Replacement Hub and Bearings for 1989 Tracker Boat Trailer
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Grease Caps Dexter Tie Down Vortex - DX66UR
- Q&A: Can Larger 3,500 lb Brake Rotor Be Used As Replacement On Trailer
- Q&A: Replacement Hub-and-Rotor Assembly for 2000 640 Ranger Boat Trailer With Tandem Axles
- Video: Comprehensive Review: Kodiak Disc Brake Kit-K2HR35D
- Shop: Vehicle Lights
- Shop: Trailer Wiring
Jacob W.
7/10/2024
Bud, I am looking for a hub for my 1995 Ranger 487VS Bass Boat Trailer. Currently, I have a 10" 5 on 4 1/2 hub with inner bearings of L68149. The ranger manual also says the outer bearing is a L68149. Is there a dexter hub that will fit my axel? The dexter 10" you referenced above has the same inner bearing but different outer bearing numbers. How can I determine if that dexter hub # K08-435-05 will fit?