Replacement for ALKO 568861 Grease Seal

Question

Question:

Need seal to replace Al-ki 568861

asked by: Thomas M

0

Expert Reply:

Hi Thomas; it looks like the old 568861 has an inner diameter of 1.719" and outer diameter of 2.565". I recommend measuring yours just to be sure. Assuming that is correct, you can use the # RG06-050 which is a pair of seals that share the same dimensions.

expert reply by: Robin H

0

Thomas

11/3/2024

Tks very much for info keep up the good work.

Answer 1

Tru-Ryde double-lip grease seal kit #RG06-050 will work as a replacement for Hayes seal 09103305 or Al-Ko seal 568861 since these parts all share the same inner diameter of 1.719-inches and the same outer diameter of 2.565-inches. Part #RG06-050 is a…

view full answer...

Answer 2

The replacement seal for 17146 is Grease Seal - Double Lip, part #58846. This is a single lip grease seal with an inner diameter of 1.719 inches and an outer diameter of 2.565 inches that is intended for 3500-lb axles. It is sold as single units. I…

view full answer...

Answer 3

For a torsion axle such as your Avan Aliner we have kits available that will give you some extra clearance. The Avan Aliner is a single axle trailer, so we have two kits that will work for you. Torsion axles must be side-mounted and not top mounted…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement for ALKO 568861 Grease Seal

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching