See what our Experts say about this LubriMatic Lubricants Sealants Adhesives

• Who Makes The Best Quality Trailer Bearings?
  Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 # TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I have seen. That said, As long as you do regular maintenance, they should last a good long time. The only downside to Terran Industries specifically is the Mobilgrease XHP 222 grease they use. It can be a bit hard to find and we have heard it does...
  view full answer...
• Bearing Kit For A Dexter 3,500 lb Axle Dexter # 61877 S/N 611553937
  Thanks for providing all of the information for your axle. This axle is going to use the standard 3,500 lb axle bearing sizing. You can use the Bearing Kit # BK2-100, which will come with bearings, races, seals, cotter pin and tang washer - everything you will need to repack your hub. We can also provide bearing grease # L11380, if you are in need.
  view full answer...
• Recommended Bearing Grease For A 2024 Forest River Grey Wolf 26DBH Travel Trailer
  Hey Stephen, There unfortunately isn't a guide to tell us what grease was used for your trailer's bearings, but it's most just a high temp red bearing grease like part # L11380.
  view full answer...
• What Electric Brakes and Grease Seals do I Need for My 2022 Discovery Rover ET ?
  Hello Sean, Thanks so much for getting that picture to me. It is most helpful. Your axles are rated for 3,500 pounds, so you will want our etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K # AKEBRK-35-SA (or the TruRyde you were looking at # TRU36FR ). These are self adjusting brakes, so one less maintenance thing you have to worry about. If you are looking to repack your bearing when you swap your brakes out, make sure to grab some LubriMatic...
  view full answer...
• Do the etrailer Electric Brakes Come in a Set? What Brakes & Bearings do I Need for 3,500 Pound Axle
  Hello Tom, Thanks for writing in. The etrailer Electric Trailer Brakes # AKEBRK-35 are sold as a pair, so each kit includes one left-hand and one right-hand brake assembly. Since it sounds like you have a tandem axle trailer with brakes on all four wheels, you'll need (2) of the # AKEBRK-35 to replace all of them. Installation is pretty straightforward. The old assemblies unbolt from the brake mounting flange on the axle, and the new assemblies bolt right back into place. Then it's just...
  view full answer...
• What Bearings, Races, Seal, and Bearing Grease do I Need for My Cargo Trailer with 2 Axles?
  Hello Timothy, Welcome to etrailer, I'm glad you found us! I wasn't able to cross-reference the number from your axle, but we can get you figured out just fine without it. Typically, a tandem axle setup on a cargo trailer comes with (2) 3,500-lb axles. You can confirm this by checking the axle tag. In that case, you will want to order (4) Hub Bearing Kits for Lippert, Dexter, and AL-KO Axles - 3,500 lb # BK2-100, one for each hub. If you check the axle tag and they are not rated for...
  view full answer...
• What Hub, Brakes, Bearings, And Grease Do I Need For My Lippert 3,500 Lb Trailer Axle?
  Hello Richard, I am sorry we did not get to your question sooner, but the great news is that you already found exactly what you are looking for! The Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles # AKHD-545-35-EZ-K is the correct replacement for your Lippert 3,500 pound axle. It has the 10" drum and 5 on 4-1/2" bolt pattern you need. I also really like that it comes pre-greased with the bearings and seal already installed, so there is a lot less mess and work when you put everything...
  view full answer...
• Replacement Bearing Kit for Dexter Axle 0404 8-219 Hubs
  Hey Alen, thanks for reaching out and providing all of the info! Knowing that your trailer is equipped with Dexter 0404 8-219 Hubs is huge - this tells me that the exact bearing kit you need is part # BK3-200 which comes with the bearings, races, a seal, and cotter pin, so you'll need one bearing kit per hub. Be sure to take some supplies like paper towels or some cloth towels to completely clean off the spindle and clean out the hub because some greases don't mix well together, and I...
  view full answer...
• What Bearings, Shackle Straps, and Equalizers do I Need to Upgrade Suspension 2022 Keystone Passport
  Hello Peter, Happy to get the right parts for you. Upgrading your suspension parts is always a great idea for a smoother ride. I do not have a database that supplies me with what is put on what camper (would be pretty sweet if there were such a list). Based on my research, I see that the 2022 Keystone Passport 219BH is equipped with (2) 3,500-pound axles. Since I don't have a list, I would double-check your axle tags to confirm. - Bearing kit (1 per wheel): Hub Bearing Kit for Lippert,...
  view full answer...
• What Threaded Grease Cap will Fit My 2 1/16" Treaded Bore, Switching from Oil to Grease
  Hello Jim, Since your hub is measuring 2 1/16", I recommend using the Bearing Buddy Bearing Protectors - Model 2080T-SS - Threaded - Stainless Steel (Pair) # BB2080T-SS. It is a great maintenance free option. Don't forget some LubriMatic Prime Guard High Temperature Wheel Bearing Grease - Red - 16-oz Can # L11380 to complete the swap. What kind of trailer is this going on?
  view full answer...
• What Bearings, Races, and Seal do I Need for My 2023 Airstream Basecamp 20 with 4,300lbs Axle?
  Hello Wallace, Looks like you got the right one ordered for your 2023 Airstream Basecamp 20, the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal # BK3-100 which is commonly for 6K axles, but your 4,300 pound axle has the beefier spindles. I am sorry for the delay in response, received quite the spike in questions and are getting caught up. If you need a return label please let me know.
  view full answer...
• Is there an Interchangeable Hub for Mine that Had DB-42 Stamped on it? 3,500 Pound Axle.
  Hello Mike, Disc brakes are brand specific when it comes to parts, if you try to mix the parts the will NOT line up. What I am showing is that the DB-42 is an older UFP set-up that uses the standard 3,500 pound axle bearings Inner bearing: L68149 and Outer bearing: L44649. Since there is no longer a hub/rotor for the DB-42 you will need to get a whole new system. The DeeMaxx Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Maxx Coating - 3,500 lbs # DE66YR would be a great kit, the bearings,...
  view full answer...
• Recommended Trailer Wheel Bearing Grease for Dexter Axles
  Usually when you replace parts that get lubricated, you clean all of the existing grease first before adding any new grease, just in case there is a compatibility issue. Since you are using Dexter axles and replacing components with Dexter parts, the grease will be compatible. For wheel bearing grease, use # L11465, or # L11380. This is a polyurea-based grease that is compatible with most grease formulas of the same or similar chemical makeup. Take a look at our grease help article, linked...
  view full answer...
• Do I Have to Use Timken Races with Timken Bearings, or can I Use Mine that were Made in China?
  Hello Dennis, You can use your current Chinese races, and just get the bearings from the Timken Bearing Kit, 14125A/25580 Bearings, 14276/25520 Races, GS-2125DL Seal # TMK32VR. You will want: - Inner bearing: Timken Replacement Trailer Wheel Bearing - 25580 # TMK44FR - Outer bearing: Timken Replacement Trailer Wheel Bearing - 14125A # TMK54FR Also, don't forget some grease seals if you do not already have some on hand. - Timken: Timken Grease and Oil Seal - Double Lip - I.D. 2.125"...
  view full answer...
• Do You Have Idler Hubs for My 2021 Coyote Tandem Axle Trailer Under Robalo Cayman 226?
  Hello again, Ken, You are looking to remove the disc brakes and just install idler hubs. I can definitely get you the correct parts. I do not have a database that tells me what is installed on which trailer, but in my research, I see that the 2021 Coyote tandem axle trailer is most commonly equipped with (2) 3,500-pound axles (you will want to double-check the axle tag to confirm). You will want the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized # AKIHUB-545-35-G-EZ-K....
  view full answer...
• What Parts Do I Need to Install the Timbren Axle-Less Trailer Suspension # T99GR?
  Hello Andrew, Time to make the switch to Axle-Less, you won't regret it! The Timbren Axle-Less Trailer Suspension System - 4" Lift Spindle - Off-Road Tires - 5,200 lbs # T99GR will work with the Easy Grease Trailer Hub and Drum # AKHD-655-6-EZ-K, and the etrailer Electric Trailer Brakes # AKEBRK-7-SA. Our hubs do come pre-greased but it does not hurt to have some extra grease on hand so you might want to grab some LubriMatic Prime Guard High Temperature Wheel Bearing Grease # L11380. You...
  view full answer...
• Are There Pre-Greased Versions Of The Dexter 008-435-05 Hub/Rotor
  Hi Wendell, We do offer compatible replacement hub/rotors for your Dexter 008-435-05 but they unfortunately do not come pre-greased. I recommend picking up the # K08-435-05 as well as bearings # L68149 and # L44649, and grease seal # RG06-050 to pre-pack the hub yourself with some lube # L11380 before the trip. To prevent the bearings from falling out or any dirt/debris from getting inside the hub you can put two layers of plastic wrap over the holes and rubber band them down.
  view full answer...
• Bearing Kit Replacement For Lippert 4,400 lb Axle
  Lippert's 4,400 lb axles use the same bearings as 3,500 lb axles so the correct replacement bearing kit is the following: - Bearing Kit # BK2-100 If you are looking for grease as well, I recommend Bearing Grease # L11380, and for a bearing packer I recommend the Bearing Packer # PTW1218.
  view full answer...
• Replacement Bearings & Grease Seal Kit For 7,000 lb & 8,000 lb Lippert Axle
  We have the exact kit you need to replace your bearings, races, and grease seal on your Lippert 7,000 lb axle. I verified directly with Lippert for you that the correct kit is the following: - Bearing Kit # BK3-200 This kit is for one hub, so if you need to replace the bearings and seals on multiple hubs, just be sure to order the correct quantity. And then for grease I recommend the LubriMatic Grease # L11380 with Bearing Packer # ALL647646.
  view full answer...
• What Bearings do I Need for My Rockwell Trailer Axle that is Rated for 3,500 Pounds?
  Hello Christian, Thanks for all the information on your trailer, it is most helpful! Since you have a 3,500 pound with tapered spindles you will need the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle # BK2-100. It will come with inner bearing L68149, and outer bearing L44649. The nice thing about this kit is that it is definitely more cost effective than buying the bearings separately, but it also comes with new races, great seal, tang washer, and cotter...
  view full answer...
• Potential Causes for Trailer Hub to Heat Up
  So long as a hub uses the correct bearings that match the dimensions of the spindle that is on the axle there is no worry about using two different brands of products, such as a Dexter hub on a Lippert axle. That in itself is not a concern. When a hub heats up it is usually from either inadequate lubrication or a castle nut that is too tight; you confirmed that neither of these applies in your situation. If the trailer is overloaded with more weight on each hub than they are rated for...
  view full answer...
• How Can I Tell if I Need a New Idler Hub on My Trailer?
  Hello Gregory, If you're wondering whether it's time to replace the idler hub on your trailer, there are a few signs to watch for. Start by looking for visible damage: cracks, bends, or heavy rust can all mean the hub is compromised. A little surface rust isn’t a big deal, but deep pitting, especially around the bearing areas or lug studs, is a red flag. Also check the wheel studs; if they’re loose, stripped, or bent, it could be safer to replace the hub than try to fix them. Another...
  view full answer...
• What Bearing Kit do I Need for My 2024 Montana High Country 295rl with 7,000 Pound Axles?
  Hello Josh, Thanks for all the information, it is most helpful. I am showing that you have a #42 spindle. The # BK3-210 kit you were looking at was almost the right kit, the grease seal is the only thing that is not correct. You need one with a 2.25" I.D., so you will need the Bearing Kit, 14125A/ 25580 Bearings, 10-36 Seal # BK3-200 for your 2024 Montana High Country 295rl. If you don't have some grease on hand, make sure you grab some LubriMatic Prime Guard High Temperature Wheel Bearing...
  view full answer...
• What Bearings, Races, and Grease Seal do I Need to Replace My Timken 2785 and 1779 Bearings?
  Hello Nathan, I had to get some of the parts added to the site, so my apologies for the delay in getting an answer. You will need one of each per hub: -Timken 2785 Tapered Roller Bearing Single Cone - Imperial - 1.75" ID for Axles & Hubs # TMK78ZR, with race # TMK88ZR (this might not pop up on our site til tomorrow 5/9 as it was just added) - Timken Replacement Trailer Wheel Bearing - 1779 # TMK94FR with cup/race # TMK66FR - Cotter Pin - 1/8" Thick x 1-3/4" Long # 165649 - For the...
  view full answer...

Do you have a question about this Lubricants Sealants Adhesive?