Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
(575 reviews)
Price: $108.11
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
Item # AKHD-545-35-EZ-K
Our Price: $108.11
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (575)
- Q & A (0)
- Photos
etrailer by AxleTek Trailer Hubs and Drums - AKHD-545-35-EZ-K
- 5 on 4-1/2 Inch
- For 3500 lbs Axles
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Hub with Integrated Drum
- 1/2 Inch Stud
- Easy Grease
- EZ Lube
- Pre-Greased
- etrailer
Hub-and-drum assembly for your trailer. For electric or hydraulic brakes. Fits 3.5K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.
Features:
- Trailer hub-and-drum assembly provides surface area for brake shoes to grip when brake is activated
- Compatible with electric and hydraulic drum brakes
- Dexter E-Z Lube and etrailer Easy Grease-compatible grease cap makes lubricating bearings fast and easy
- Remove rubber plug to access zerk fitting on spindle - no need to disassemble hub
- Sturdy iron construction
- Zinc-enriched paint on drum adds durability
- Zinc-finished bolts resist corrosion
- Pre-greased hub-and-drum assembly is easy to install - no need to pack bearings
- Lithium complex, multipurpose grease keeps bearings lubricated
- Bearings, races, grease seal, grease cap, and lug nuts are included
- QAI and CSA certified
Specs:
- Application: 3,500-lb Dexter E-Z Lube and etrailer Easy Grease trailer axles with #84 spindles
- Compatible with standard axles from most manufacturers, including Dexter, Lippert (LCI), and AL-KO
- Actual drum dimensions: 10" diameter x 2-1/2" wide
- Works with 10" brake assembly
- Bolt pattern: 5 on 4-1/2"
- Wheel studs: 1/2" diameter x 1-1/4" long
- Grease cap flange diameter: 1.99"
- Weight capacity: 1,750 lbs
- Limited 1-year warranty
Bearing, Race, and Seal Information
- Bearings (included)
- Inner bearing: L68149 (1.378" inner diameter)
- Outer bearing: L44649 (1.063" inner diameter)
- Races (included)
- Inner race: L68111
- Outer race: L44610
- Grease seal (included): 58846
- Inner diameter: 1.719"
- Outer diameter: 2.565"
Thoroughly Tested for Safety
This hub-and-drum assembly meets the requirements for certification by the Canadian Standards Association (CSA). The CSA creates standards, which when complied with ensure a safe and quality product. This assembly underwent extensive testing to measure stopping distances when braking. This assembly has also been tested by QAI for braking performance in a complete automotive setup and under real-world conditions to provide the most realistic scenario for the everyday driver.
E-Z Lube and Easy Grease-Compatible Assembly for Simple Lubrication
The grease cap on this hub-and-drum assembly is specially designed to work with your Dexter E-Z Lube or etrailer Easy Grease axle to make lubricating bearings quick and easy. Just remove the plug on the grease cap, attach a grease gun to the zerk fitting on the end of the spindle, and inject the grease. It will flow easily to both inner and outer bearings. Not only does this make lubricating the bearings easy, but it also helps to prevent corrosion of the hub. This is because you can lubricate the bearings without the mess of taking apart the entire assembly.
Determining the Bolt Pattern
The first number in the bolt pattern is the number of bolt holes. The second number denotes the diameter, in inches, of the circle on which the bolt holes sit.
On wheels with an even number of bolt holes, measure from the center of one bolt hole to the center of the hole directly across from it. (Example: 8 on 6-1/2 means 8 bolt holes with 6-1/2" from the center of one hole to the center of another on the opposite side.)
To determine the bolt-circle diameter on wheels with an odd number of bolt holes, measure from the center of any bolt hole to the point halfway between the two bolt holes directly across from the first. (Example: 5 on 4-1/2 means 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolt holes.)
Measuring the distance (D) from the center of one bolt hole on the wheel to the center of a bolt hole right next to it can also help to determine the bolt pattern.
- If D = 2-5/8", then the bolt pattern is 5 on 4-1/2"
- If D = 2-3/4", then the bolt pattern is 5 on 4-3/4"
- If D = 3", then the bolt pattern is 5 on 5"
- If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
KBD2-545-19 AxleTek 10" Trailer Hub and Drum Assembly for 3.5K Axle with Hardware - 5 on 4-1/2 - EZ Lube - Pre Greased
Compare to Dexter 84546UC3-EZ
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
- Product did not meet expectations
Customer Reviews
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased - AKHD-545-35-EZ-K
Average Customer Rating: 4.7 out of 5 stars (575 Customer Reviews)
Hub-and-drum assembly for your trailer. For electric or hydraulic brakes. Fits 3.5K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.by: David06/12/2024
VERY happy with this hub: an exact OEM match. I am leaving on a 6,300 mile U.S. Coast to Coast (and back) trip, and was going to purchase a set of wheel bearings, races, dust caps, etc. THEN realized that for just $[XX] more, I could buy an entire new hub -bearings installed AND pre-greased- to take with me. IF I have the misfortune of a wheel bearing failing, I now will not have to replace a bearing along the highway, just swap the hub out. Customer service was THE BESST EVER from moment of order through receiving my product. etrailer is DEFINITELY my "go-to" source for all things Trailer :-)/
by: Roderick07/22/2023
Hubs matched to my original Dexter hubs. The prices was more than 50% less than Dexter axles; well worth the savings.
Bearings came installed; made installation a breeze. Slide them on and put on retaining washer, nut and retaining bracket.
I’d buy them again (today) will re-evaluate in a year.
by: Jess12/11/2023
This is the trailer I built using your spindles and electric brakes.
It towed beautifully from Texas to Kansas City and back for the World of Wheels.
by: Robert08/31/2022
Easily installed... Pre-greased bearing... Should have come with new axel nut, cotter key and bearing washer, but didn't.. Used old ones...
Brooke M.
9/17/2022
Thank you for reaching out. I have sent this to our customer service team and they will be in touch about the missing pieces.
by: George07/15/2023
Purchased a used 2016 Keystone Hideout Trailer and wanted to be sure it was safe going down the road. These four assemblies were clean, packaged well and fit as expected. We will be headed out to campsite next month and will update this review ONLY if their is a discrepancy, otherwise, we are very satisfied with our etrailer purchase.
by: Jacob 05/28/2024
I will shop with this team again. The communication was great and it's great to know they know what they are selling and that it will fit your trailer/camper. Good service is so hard to find these days so we should shop with and support those who support American jobs and give great support. If the customer service were to be changed to a foreign country, I would have a change of heart.
by: Marcus05/22/2024
Part are great. Shipping was quick and communication was great. No issues with the transaction. Minus one start for less than adequate packaging for transport. I’ve had two orders. The hub that came with other items was in a box in a box. The other items were just loose in the box without protection. No damage noted, but the potential is there depending on the handling practice. Hub that cam skin was in its own box. Appreciate the reduced number of boxes, but this wasn’t sufficient. No damage to the part, but the outside of the.hub poked through the box, the plastic was pulled out and shredded and the hi. Protective cap was damaged.
by: Jeffrey02/12/2024
Pleased with the quality of these hub/drum assemblies. Bearings were nicely pre-greased. Kit comes with solid bearing hub covers and bearing buddy types with removable rubber grease plugs...your choice.
by: James 04/29/2024
Product replaced OEM part exactly. product was fully lubed as advertised. Installation was simple.
by: Shannon04/29/2018
I ordered the hub and idler set, my trailer came with 15x5 hubs and I ordered 15x4.5 rims. Since they wouldn't return my rims I ordered the correct hubs from etrailer. Got my box only had one seal slightly damaged. Installing was a breeze and happy with my purchase... Website was very user friendly as my first plan was to do a 6lug but I talked myself out of it. Thanks etrailer good job, nice company to deal with.
by: Jeffery03/28/2024
One of the lug nuts was damaged and could not be used. I would like a cotter pin and a flat washer included in this assembly.
by: Donald 02/12/2024
I think your a great company but my hub drum assembly was a little out of round.
This is probably from storage by the manufacturer.
Have great day! Don
by: Lawrence11/11/2023
I ordered an easy grease trailer hub and drum assembly to replace the one on my 14 foot cargo trailer which was damaged by a defective magnet. The one I ordered fit perfectly. Since it came pre-greased, it saved quite a bit of time because I did not have to pack the bearings and press in the seal.
by: Mike06/03/2017
This is my second order. I ordered for the rear axle first. The parts looked good. So ordered for the other axle. The seals are robust and double seal design. But the bearing are China bearings. Would have liked to seen timkin or the like but are serviceable. The break kit fit well and looks good. We will see how they do on my 2500 mile round trip thru the mountains with a small truck loaded on it. The operators both times were very friendly and knowledgeable about their products. Keep up the good work and I'll keep buying!
Mike
6/3/2018
Put about 3000 miles with zero issues. They performed better than expected. I have ordered several items since then and the operators are all knowledgeable and all ways willing to do what they can to ensure a proper order and that Im satisfied with my order
by: John 05/15/2024
Very good quality and easy to install I highly recommend this company for all your trailer needs
by: John03/28/2024
I haven't received my leaf springs at the same time. I ordered them within minutes of each other. So I have to wait until next week now. Once I get things together I can make an accurate assessment. Probably the only gripe of mine is that I have to wait now. Thanks for the follow up.
by: Keith 03/20/2024
drums and brakes went together perfectly. Amy J was a big help.
by: Buck.04/15/2024
Fast service. Help us work through getting good replacement parts. Thank you.
by: Brian07/10/2023
Missing parts, one of the two kits I ordered was already opened an missing the caps
Rebecca N.
7/13/2023
It is a bummer that it arrived missing the grease caps. I will have our Customer Service team reach out to you.
by: Royce05/26/2024
i really do like it,good items pretty sturdy and price is good and super fast shipping A+++++++
by: Allen09/11/2023
Received the hubs very quickly. They were well greesed and ready to go. They look well machined. I did have one lug nut that had something wrong with the threads. I might could have used it, but since it would not thread on by hand I did not want to try it since it might damage the stud. I went on line and did a chat with etrailer. Thier customer service is top rated. They shipped me out another lug nut. This is why I do business with etrailer. They understand the needs of the customer and understand the products they sell.
I installed the hubs this weekend and took the trailer for a test pull. Needed to adjust the brakes up a little, but all was well.
by: David 02/07/2024
Service was great and the shipping was fast. As always etrailer out performs its competitors.
by: Brian05/25/2024
your trailer selection and specifications were not right for my Forrest River. your site said it has 3.5 k axles but it really has 4 k which regulate different parts. i returned the parts and sent your prople the manufactures delivery sheet so you can update your site.
by: Albert B05/15/2024
13,737 miles to Fairbanks from Ft. Myers and bank, still going good.
by: Walter 07/23/2023
Perfect fit for the corresponding e-trailer brake assembly. Even comes with lug nuts, but I didn’t use them because they are a size up from whats on the rest of my trailer wheels. Same thread, just different lug wrench size. Personally, e-trailer, I’d forgo including the lug nuts and instead, include the mounting hardware with your e-trailer brake assemblies.
25
575
Show More Reviews
See what our Experts say about this etrailer Trailer Hubs and Drums
- Replacing Lippert 3,500 Pound Axle with 76 Inch Spring Seat Length Your trailer is equipped with a Lippert 3,500 pound axle that has a 95 inch hub face length and a 76 inch spring seat length. The closest replacement axle we have available to these specs is the Dexter Trailer Axle # 7359765-EB that features a 95 inch hub face length, an 80 inch spring center length, and a 3,500 pound weight capacity. The axle comes with hub and electric brake assemblies already mounted. If you were to use this particular axle on your trailer though new spring seats would...
view full answer... - Recommended Axle-Less System For 2000-Lb Off-Road TrailerSince the trailer you are building is 2,000-lbs or less the axle-less system I recommend is part # ASR2KHDS09. This is the Timbren system with a 4-inch drop and it is designed for off-road tires. It has a weight capacity of 2,000-lbs and has EZ Lube spindles that make it easy to grease the bearings without having to remove the hubs. This system has a 4-bolt brake flange. If you do not plan on adding brakes I recommend part # AKIHUB-555-35-EZ-K idler hubs. This hub has a 5 on 4-1/2 wheel...
view full answer... - Replacing Torsion Axles with Timbren Axle-less System on a Trailer Used to Make Tear TrailerThe axle on the trailer you are going to purchase is probably a 3,500 pound axle. To determine if the Dexter hubs will fit the spindles on the Timbren Axle-less system # ASR3500S05 we need to know the inner and outer bearing numbers stamped into the sides of the bearings. They are likely going to be L68149 for the inner and L44649 for the outer. If they are then the hubs will fit the Timbren system. But I do recommend going ahead and getting brakes on the trailer because the laws for when...
view full answer... - Losing Grease from etrailer Trailer Hub and Drum Assembly Part # AKHD-545-35-EZ-KThe Bearing Buddy Bearing Protectors part # BB1980A-SS are indeed correct for the etrailer Trailer Hub and Drum Assembly part # AKHD-545-35-EZ-K. Have you noticed any grease on the outside of your wheels/tires? If grease was leaking out of the Bearing Buddy Bearing Protectors then there would be grease all over your wheels and tires. It wouldn't just fly off either so you should notice it if present. If there isn't any grease on the outside of your wheels/tires then odds are it is leaking...
view full answer... - Adding Electric Brakes to 3,500 lb Axles of LOOK TrailerFor 3,500 lb axles you will use 10 inch assemblies. My recommendation is the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs # AKEBRK-35-SA. These assemblies will work well for your axles. If you don't already have the hub/drum assemblies, then I recommend using the Trailer Hub and Drum Assembly - 3.5K E-Z Lube Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased # AKHD-545-35-EZ-K. This combination will work well and if you are adding brakes for...
view full answer...
- Replacing Hydraulic Surge Trailer Brakes with Electric Drum BrakesDexter 10 x 2-1/4-inch electric drum brakes # 23-468 and # 23-469 are a perfect choice for your 3500-lb axle that has a 4-bolt brake flange. We see more and more boat trailer manufacturers specifying electric drum brakes as standard equipment due to their lower cost and easier installation. Electric brakes require a compatible brake controller like the Prodigy P2 # 90885. To choose new hub/drum assemblies you'll need to know the bearings used in your existing hubs; this will ensure new...
view full answer...
- Availability of Parts to Convert Mobile Home Frame to Utility TrailerWe offer a wide range of trailer axles, hubs, brakes, wheel and tires. I have included links to all product pages for you. New hubs need to use the same bearings as the ones being replaced. This ensures the new hubs will fit on your spindles. You also want to choose hubs that have the weight capacity needed for the axle and the same bolt pattern as used by the wheels/tires you want to install. You can check the axle for a sticker that indicates its capacity. One thing you'll want to note...
view full answer... - Recommended Axle-Less Suspension System For Small Home Made TrailerI recommend going with an axle-less system. Due to the size of the trailer you will have a much easier time finding the right fit and you will not need to worry about the suspension like springs or hangers. The system I recommend is part # A12RS440. This system is designed with a capacity up to 1,200-lbs and has hubs with a 4 on 4 bolt pattern already installed. I have attached a link to a review video for this system you can check out. The 12-inch tire/wheel combo I recommend is the...
view full answer... - Should I Change My 5 On 5.5 Wheel Bolt Pattern To Something More Common?With the options being as limited as they are for the 5 on 5-1/2 bolt pattern, I do recommend changing to something more common, specifically the 5 on 4-1/2 bolt pattern. This is very widely available and it will not only give you more options for wheel design, it will also be significantly easier to replace if ever needed. The only drawback to doing this is that you will indeed need to replace your hubs to get the new wheels attached. The vast majority of hubs that used the 5 on 5-1/2...
view full answer... - Solution for Getting Trailer to Drop 2 inches to Fit Through Barn Garage DoorThe smallest wheels we offer that will fit over a 10 inch drum are 13 inches. I wish we had a smaller wheel that would fit. If it's just a garage door that you are trying to get past you could deflate the tires to the point where the trailer loses 2 inches in height, move the trailer past the door, and then reinflate the tires. Be sure to remember to do the same thing to get the trailer out!
view full answer... - Replacement Hubs and Brake Assemblies for Dexter 023-217-00What you have is a 10 x 2-1/4 inch brake assembly that's typically found on a 3500 lb capacity axle. We offer the # AKEBRK-35-SA from AxleTek or the # 23-468-469 from Dexter that would provide perfect replacements. I prefer the US manufactured Dexter product. These are self-adjusting brake assemblies. Once installed, you'd want to take them to a large empty parking lot and actuate the brakes at moderate speed about 25 times to get them initially adjusted. From that point on, they'll...
view full answer... - Replacement 10" Electric Brakes for a 1995 Fleetwood 5th Wheel TrailerThank you for all of the info! Since your current drums are 10" that means you need the 10" Self-Adjusting Electric Trailer Brake Kit # AKEBRK-35-SA. If you're needing to get new hub/drum assemblies then we do have some replacements for you. The 2-3/4" measurement you took means that you have a 5 on 4-3/4" bolt pattern so I recommend using the assembly # AKHD-5475-35-EZ-K. With that being said, the most common bolt pattern is 5 on 4-1/2" and while 5 on 4-3/4" isn't impossible, it isn't...
view full answer... - Replacement Hub, Drum and Brake Assemblies for AL KO 3,500 lb AxleThe one piece of info I need from that pic is partially blocked by the bent plate. What is the full capacity number listed? With that I can see what we have that you'd need.
view full answer...
- How to Pick Out Replacement Hub for EZ Loader Trailer AxleIn order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. You gave me that info so we are on the right track. Next thing you will need to know is what spindle you have on your trailer. In order to do that you can either get the inner and outer bearing numbers from a hub or use a dial or digital...
view full answer... - Problem with Adjusting Lippert Forward Self Adjusting Brakes As we do not carry the Lippert brakes, I cannot say for sure what is going on as I have not had the chance to mess with them before. However, if you had say an etrailer.com Left Hand Self-Adjusting Electric Trailer Brake Assembly # AKEBRK-7L-SA, I would say it is most likely one of two things. First, something has become disconnected on the brake. This does happen every now and then and can be confirmed by removing the hub/drum. If this has happened, you can most likely just reattach the...
view full answer... - Trailer Hub/Drums for 3500-lb Axle with Drum BrakesThe trailer hub # AKIHUB-545-35-K is an idler type hub that is intended for trailers without brakes. On the linked page you can view all hub/drums for trailers with drum brakes that carry the same 3500-lb axle weight rating, use the same 5-on-4-1/2 bolt pattern and use the same set of bearings, inner bearing # L68149 and outer bearing # L44649. Any new hub has to use the same bearings as your old one in order for it to fit on your spindles. An example is part # AKHD-545-35-EZ-K. These...
view full answer... - Replacement Hub/Drum and Brake Assemblies for 2017 KZ SportsmanHey Kent, with just the info you gave me I can let you know what you would need. The correct bearing kit would be the part # BK2-100 and for brake assemblies you'd want the part # TRU36FR. If you happened to also be looking for hub/drums you'd want the part # AKHD-545-35-EZ-K. These actually come with bearings so you wouldn't need to also buy those if this is what you needed.
view full answer... - Parts Needed to Add Electric Drum Brakes to a Home Made TrailThe first thing you are going to want to check would be the axle to determine if it has brake mounting flanges welded on. A brake mounting flange on an axle/spindle would looks similar to # TRU74FR or # TRU37FR . The flange is that piece with the holes about midway down each of those examples. If you do not see those on your axle then they will have to be added. This is a precision job that requires a professional welder with the special jig needed and experience with welding on brake...
view full answer... - Correct Hubs and Electric Brake Assemblies to Use with Timbren Axle-Less System # ASR1200S04The etrailer 3,500 Pound Trailer Hub and Drum Assembly # AKHD-545-35-EZ-K that you referenced is indeed the correct hub/drum for the spindles on the Timbren Axle-Less Trailer Suspension System # ASR1200S04. These will fit with this system perfectly and they feature a 5 on 4-1/2" bolt pattern. This is the most common pattern for this capacity but you will just want to make sure it matches the hole/bolt pattern on your wheels. I have attached an article on measuring your bolt pattern if...
view full answer... - Correct Replacement for Tru-Ryde Hub/Drum RVD-H-545The Trailer Hub and Drum Assembly part # AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part # AKFBBRK-35.
view full answer... - Parts Needed to Add Electric Drum Brakes to a TrailerThe first thing you need to do is check the trailer axle to see if it has brake mounting flanges. It will look like the square part welded onto # TRU74FR. If the trailer does not have those they will need to be added by a professional with experience in welding on brake flanges because it is a precision job. For a 3,500 pound axle you would use # 4-35 sold in quantities of 1. You would need 2 per axle. You will also need to have hub and drum assemblies. For this I would need to know the...
view full answer... - How Much Does Timbren Axle-Less System w/ Hub # A35RS545 Weigh?The weight of the Timbren Axle-Less System, # A35RS545, is right at 50 lbs for each side and make up a total of 100 lbs of your trailers GVW. This is pretty comparable, maybe slightly less, in weight compared to a traditional axle and leaf spring suspension. If you ever want to add electric brakes to this kit, I suggest picking up the following parts: Brakes - # AKEBRK-35-SA qty 1 Drums - # AKHD-545-35-EZ-K qty 2 7-Way Wiring Kit (If you need wiring for brakes) - # HS381-9000 qty 1 Brake...
view full answer... - Complete Axle-Less Suspension And Electric Brake Setup For 1990 Aliner CamperI do have a solution for your axle. It looks like you have a torsion axle on your 1990 Aliner Camper, which we do not carry. I recommend going with an axle-less suspension setup. This will replace your current axle and suspension. If you are wanting a 3,500lb rated axle then you can go with Timbren Axle-Less Trailer Suspension System Straight Spindle # A35RS545 or go with Timbren Axle-Less Trailer Suspension System 4" Drop Spindle # A35RD545 which has 4" drop for lower ground clearance....
view full answer... - How to Determine if Trailer Brake Magnets/Brake Assemblies and Hub and Drums Need to Be ReplacedThe way you are describing testing your brake magnets is the way we recommend testing the brake magnets, by connecting the multimeter to the blue brake wire behind the brake controller. When testing your trailer with 4, 10 inch brake drums, the maximum amperage should be between 15.0-16.3 amps at 12-13 volts. Assuming the appropriate voltage is reaching the brakes, the 0.025 amps reading is much too low for your trailer brake magnets. I have attached a help article on testing brake magnets...
view full answer...
Do you have a question about this Trailer Hubs and Drum?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Edited by:
Lindsey S
Installed by:
Jeff D
Installed by:
Randy B
Video Edited:
Joshua S
Video Edited:
Jacob T
Video by:
Chris R
Video by:
Zach D
Video by:
Jonathan Y
Updated by:
Wilson B
Updated by:
Mike S
Written by:
Alexander C
Test Fit:
Shane H
Test Fit:
Kevin C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Brooke M.
6/17/2024
Wow, coast to coast AND back? That sounds like quite the adventure! How long will it take you to do that?