To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Get a brake controller in your truck that looks like it's supposed to be there. This sleek knob blends right into your dash and makes your settings simple and convenient to adjust.
Features:
Specs:
Note: The main unit must be mounted horizontally level and parallel to the direction of travel within 20 degrees.
Power output: To get more power output - the maximum amount of power that will be applied to your trailer's brakes - rotate the knob clockwise. To decrease the power output, rotate it counterclockwise.
Manual override: To engage manual override, simply press the knob. This will activate the trailer's brakes and brake lights independent of your tow vehicle, great for stopping sway or controlling your trailer's momentum in an emergency. The Voyager iD will reach the maximum set power in half a second.
The Voyager comes in 2 pieces: the main unit and the control knob.
The control knob can be installed in any convenient spot that's easy for you to see and access. This can be a blank switch panel, an open spot on your center console, or wherever there's space on your dashboard. Before you do any drilling, be sure there's enough clearance behind the dash for the entire knob to install!
Once you've decided where you want to put the control knob, you'll need to find a good place to install the main unit. It needs to be horizontally level and parallel to the direction of travel within 20 degrees. A mounting kit with hardware is included.
This kit comes with a vehicle-specific wiring harness that plugs right into the factory port beneath the dash of your vehicle. That means no hardwiring!
You will also need a circuit breaker kit to complete your installation:
Note: If you don't already have a 7-way plug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately).
Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Voyager iD uses an internal inertia sensor to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on this 2010 Toyota Tundra we are going to install part number 90885-3040P. First thing we will do is show you where the port is on the vehicle, this has a factory tow package. It is going to be underneath the dash on the left hand side. First thing we are going to do is plug the adapter cord into the factory port right here. Next, we are going to take our ground wire and ground it to the piece of sheet metal right here next to this fastener. :31
Then we will take our cord and route it behind the dash and over to our location where we are going to install our brake controller. We will let that sit for now. There is not much room to install the brake controller. This is because we can not do anything in this area here because that is where the air bag is. So what we are going to do is mount it offset. We will mount it to the flat spot here on the plastic. Make sure there is nothing in the way. We will have the bracket offset this way. 1:08
Now when we install this we are going to use just one side of the bracket. We are going to put our screw on this side and this side to help hold it up. Now that a second to set your brake controller up, make sure it is straight and aligned with the vehicle. Then we will use the other screw to help set it in place. Now we will plug the adapter cord into the back of the brake controller and then install the brake controller on the bracket. Snug up the screws. 1:56
Now this is tight quarters, what you can do is use a bit and a 1/4 inch wrench on the end to help you get a little extra torque in. With that, our brake controller is already installed. There you have it for part number 90885-3040P.
Everything worked as it should! Very happy with the look as well
Works good
The install was pretty simple. It took some time to modify the knock out plug to conceal the adjustment knob but after a bit of work it fit nicely and looks like it’s supposed to be there. I missed a photo of the final mont of the control unit but I was able to install the supplied clip for the module just above the airbag. There is a clip that holds the wire for the computer input so I removed it for extra space and secured the wire with a zip tie.
Works great. custom harness makes it plug and play!
Easy install. I used the cable harness that came with my 22 Silverado. Hardest part was just locating a place on the dash for the knob and access from behind for the 2 inches or so length of the switch assembly. Small and looks good on the dash.
2 minute installation. Nice product.
Great unit, plug and play!
Easy to install. Great service. Thank you.
Easy to install and works great!!
It was just what I wanted
great item
Made install super easy.
works good
Pleasure to do business with.
Just what I needed!
High Quality.
Makes brake control insall a snap!
all arrived quickly without any problems
Did the job just fine. Easy to install
Do you have a question about this Trailer Brake Controller?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.