Is this right for you? Product Expert Kathleen M says:
Yes, if you:
Prefer a solid white lid that lets in light without the sun shining through and heating up your camper
Boondock often and just need something basic to move some air while not eating up much power
No, if you:
Stay in areas with frequent rain and don't want to risk damage to the inside of your trailer
Have a 20' long or larger RV and need something with more oomph to pull more air out
Find it difficult to reach up to the ceiling to turn a knob or switch
This roof vent uses a 12-volt fan to circulate air in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. Wedge-shaped, white plastic vent cover opens and closes with a hand-operated crank. Lowest Prices for the best rv vents and fans from Ventline. Ventline Ventadome Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White part number V2094SP-30 can be ordered online at etrailer.com or call 1-833-496-1390 for expert service.
All Info
Reviews (890)
Q & A (0)
Related Parts
Photos
Why etrailer?
Ventline RV Vents and Fans
- V2094SP-30
Roof Vent
With 12V Fan
Vent
14W x 14L Inch
White
Manual Lift
Ventline
4-1/2 Inch
This roof vent uses a 12-volt fan to circulate air in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. Wedge-shaped, white plastic vent cover opens and closes with a hand-operated crank.
Features:
Roof vent's electric fan yields better air circulation than non-powered models, exhausting hot air while trailer or RV remains locked and secure
Simple to upgrade from non-powered model
Basic, hand-operated crank rotates to open and close dome
Switch to turn the fan on/off is mounted on the vent
Translucent cover allows some light through
Aerodynamic, wedge-shaped dome made of durable polypropylene
Galvanized steel roof flange won't rust or corrode
Snap-out screen is easy to clean
Polar White interior trim piece (or garnish) is included
Fan uses 12-volt DC power
Wiring sold separately
Made in the USA
Specs:
Included garnish fits roofs 1-7/8" to 3" thick
Garnish leg length (depth): 2-1/8"
Garnish color: Polar White
Other garnish sizes are available (sold separately)
Fan power: 12-volt DC
100 CFM
Cover color: white
Rough opening size: 14-1/4" wide x 14-1/4" long
Vent extends above roof:
4-1/2" Closed
10" Open
2-Year warranty
Notes:
Screws and sealer are not included. See Installation Kit (344270KITW), which includes all necessary screws and sealer to install vent.
Not for use above tubs, showers or range cooking surfaces.
Installation Instructions
Mark desired location for vent. Be sure to choose a location between roof joists.
Cut a 14-1/4" x 14-1/4" opening through roof and ceiling. (Or use existing opening if you're replacing a standard 14-1/4" x 14-1/4" vent.)
Apply sealant to bottom of flange. Be sure to surround each screw hole.
Insert vent through hole with screen frame extending through roof cavity and hinge of vent toward the front of the vehicle.
Mount to roof with #8 screws.
Remove screen frame and wiring compartment cover to make electrical connections.
Connect to 12-volt DC power source
Replace screen frame and cover.
Attach interior garnish piece with #8 screws.
V2094SP-30 Ventline Ventadome Trailer Roof Vent - Manual Lift - 14-1/4" x 14-1/4" - White
This roof vent uses a 12-volt fan to circulate air in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. Wedge-shaped, white plastic vent cover opens and closes with a hand-operated crank.
by: Paul06/11/2022
Great replacement bathroom vent, better customer service.1311349
by: John05/22/2021
Ordered ac seal,plumbing boots,bathroom vent and refrigerator vent covers. Descriptions of items were right on.1046860
I found this vent and fan combination to be just what I needed. I added it to the roof of my enclosed motorcycle trailer. It's made a big difference in keeping the inside of my black trailer cooler. Unless you have sheet metal screws and sealant around the shop, I'd order the install kit. This product does not come with a template for instilling it. I made my own out of thin plywood. Watch the edges of the metal, they are sharp. 46909
by: Bob C04/30/2017
Ordered a Ventline Roof Vent, the total system from the top cap, shroud (extra deep), fan and ceiling fittings. Received promptly, everything as ordered, delivered promptly. Everything fit. ETrailer has become my primary parts source.375356
by: Kerry S10/23/2012
This item arrived when they projected it would. As always I'm very happy with the service and how quick they responded when I had a question. I will definately continue to give them my business. I have not yet installed the roof vent so I can't send a picture. 57953
Comments
It still works like its brand new. I actually bought another one this year for another location.
Kerry - 04/23/2014
3720
by: Rosco08/15/2017
I purchase a small 1985 travel trailer and the vent fan stop working. I search online for the best price, well this product review should tell everyone this item wasn't bought at camping world. etrailer.com has the best online prices and great DIY videos. Thanks.420475
by: Danthecarpenter08/20/2015
Some reviews said this product was flimsy. I found it to be the same quality or bette than every RV vent that costs more than this one. The nice thing about this one is the screen is easily removable, unlike other RV vents I've used. The opening mechanism works as good or better than others. Overall I'm happy with the quality and operation of this vent.220686
by: Faye07/31/2021
Been in the camper for a year now and no leaks. Product is excellent . When done looked professional done .1115618
by: patrick D.07/10/2015
Shipped quickly, arrived in perfect condition. Customer service was outstanding. So nice to be able to talk with a real person and one who is so customer friendly.210952
Comments
When we need anything for the RV we will definitely buy from you, thanks for excellent service and products.
patrick D - 07/29/2016
19794
by: Rodney01/15/2019
Great vent for the price. Replaced due to hail damage. Seals nicely and lets a good amount of light through. Smooth operation opening and closing. 597833
by: William P.12/21/2015
This item was received in good order. Fantastic and I plan on doing more business with you in the spring.
Thank you so much234010
by: Brian 09/13/2021
Great help from Lazer! He’s the best i ndeed!1151205
by: Jeffrey L E09/10/2013
Good quality. 12V fan is small but moves air well. Also is quieter than the original unit it replaced.99216
by: Diane11/22/2013
The product arrived exactly as expected and was easier to install than expected. With the excellent pricing, this is our new RV parts store. Thanks!!108175
by: Jason D05/30/2017
Great little fan. It moves some air for being so little. Just wish I would've researched more as it turned out, I do need a bigger fan. Very easy to install however. 386510
Comments
Still good. Helps a bit with circulation when using a small electric space heater in my pop up camper.
Jason D - 05/30/2018
39084
by: Raina05/19/2021
This fan worked great and was easy to i nstall.1041865
by: Daniel06/29/2018
Rest assured, most aftermarket parts you buy to repair you rv with, are much better quality than the cr#p the manufacturers build with.528503
by: Guy D.04/10/2018
Received vent fan in a timely fashion,product looks excellent.l will be using it in a food truck.494629
by: M Davis 04/12/2015
Exactly as our old vent. Easy to install. Product shipped immediately. Company sent emails updating delivery. Completely satisfied. 184789
by: Eugene 04/15/2020
Good quality vent as compared to some of the less expensive units looks good when installed779188
by: Good04/21/2017
Good quality. Needs to be packaged better. Vent flange was bent in a couple of places during shipping.370606
by: jeff d07/29/2016
same as original that was damaged by hail. still required putting and additional cover over this product to prevent future damage277476
by: Joel h.09/15/2018
we installed the vent and it seems to be doing a great job.... we have no complaints about the product or the service565378
by: Jim Nn11/21/2017
Very happy with entire process. Good selections, courteous sales staff. Had pleasure in ordering parts Sales people were helpful and made the whole thing enjoyable. Yours Respectfully, Jim N.454025
by: Kent K06/04/2012
A nice looking unit, packing included everything needed to make the install go smoothly. It fit easily into the old hole and other than adding wiring for the fan (old unit didn't have a fan), it only took about an hour to install.42592
Yes, as long as the MaxxAir Vent Cover you have on your trailer is MaxxAir II then the Ventline Ventadome Trailer Roof Vent # V2094SP-30 would work well with it as this is the size vent the # 67277 was designed to fit. view full answer...
The Ventline Ventadome Trailer Roof Vent # V2094SP-30 that you referenced is an exhaust fan, what that means is that it pulls air out of the the trailer.
The reason for this is that hot air rises, so when you pull out the air at the top of the trailer you will be removing the warmest air and replacing it with cooler air.
I am not sure if this would be sufficient to keep your candy from melting while they are being transported through a hot desert climate. You might have to pack them in... view full answer...
The fan itself only fits onto the motor one way. If you wanted to reverse the rotation of the fan you would need to switch the positive and negative leads on the back of the motor. I tried this with just the motor and it will reverse the rotation. However, since the fan can only be put on one way and the blades are at a fixed angle, reverse the motor direction will also reverse the air flow direction. view full answer...
In order to convert your manual operated vents in your motorhome, and the brackets and hardware that would allow you to convert their vents is very limited. We do not currently carry those parts in stock so I would need the make and model of your vents to try and locate parts that would work.
You may be better off replacing a vent with a vent that has a motor already included like part # V2094SP-30. This is a 14-1/2 x 14-1/2 inch fan with a 12 V motor and white lid. The on/off switch... view full answer...
The Installation Instructions for the Ventline Ventadome Trailer Roof Vent # V2094SP-30, do not mention using a inline fuse. They show the connection going straight to the 12V battery source.
I have seen these installed and wired into the nearest light source. The only draw back is the fan will only receive power when the light switch is on this way. view full answer...
To remove the screen from the Ventline Ventadome # V2094SP-30 you simply need to pull down on it from inside the trailer so there is no need to get on top of your trailer roof. If you check out the attached review video you can see this done. view full answer...
The smoke and white covers that are on the Ventline roof vents are both going to let quite a bit of light into the trailer. However, due to the translucent nature of the smoke covers they would let more light in.
Both would last about the same amount of time. One has not been shown to stand up to the sun better than the other.
For a smoke version of the part # V2094SP-30 that you referenced you would want the part # V2092SP-29. view full answer...
I do have an option for you but the correct replacement screen is not available as it has been discontinued by the manufacturer. The only option we can offer you is a new unit, the Ventline Ventadome Trailer Roof Vent part # V2092SP-28 or part # V2094SP-30 with fan. These units will however be a direct replacement for the Northern Breeze Vent you have now. view full answer...
We have the Ventline Roof Vent w/ 110V Fan # V2128SP-01 which fits a 14-1/4" wide x 14-1/4" long opening and roofs that are 2-1/8" to 3-1/4" thick. It is a 110v fan, there is not a 120v fan option.
If the 110v option does not work for you, we also have it in a 12v option.
- Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-30 (Fits 1-7/8" to 3" thick roofs) view full answer...
It sounds like you are trying to figure out how to install the Ventline Ventadome Trailer Roof Vent # V2094SP-30 on the roof of your 2005 Dodge Sprinter and the concern you have is the thickness of the roof of your vehicle.
The garnish that is included with the # V2094SP-30 can be trimmed down for thinner applications so it would still work on your vehicle. To complete the install you may also be interested in the install kit part # 344270KITW. view full answer...
After inspecting roof vent # V2094SP-30 and the included bezel, I have come to the conclusion that you would just need to trim 13/16 of an inch off the bezel on the end that sticks into the vent. This should allow you to flush mount the vent and bezel in your 1 inch thick roof.
I also recommend installation kit # 344270KITW which comes with the hardware, tape, and sealant needed for installation. view full answer...
In order to determine which roof vent will fit your 1988 Holiday Rambler Imperial RV, you will need to take a couple of measurements. The Ventline Roof Vent, # V2094SP-30, requires a 14-1/4 by 14-1/4 inch opening to install. The included garnish is designed to fit roofs 1-7/8 inches to 3 inches thick.
If these measurements match the opening size you currently have on your RV then you can use this vent or any vent that fits the same opening size. Replacement roof vents are not tested to... view full answer...
The Ventline Ventadome Trailer Roof Vent w/ 12V Fan, part # V2094SP-30, is the same size as the vent you are replacing which is 14-1/4 inches x 14-1/4 inches. It is a power vent so it can be wired like your existing power vent. It will work in your 1991 Fleetwood Bounder motorhome as long as you will not be using it above a bathroom tub or shower.
The Ventline power vent is not approved to be used above a tub or shower because the electrical motor is not tested to hold up to the moisture... view full answer...
The guts of a higher capacity fan would not fit in Ventline vent # V2094SP-30 without fairly extensive modification so I do not recommend it. The best solution would be to remove the vent assemblies and install newer, higher capacity options.
Fan # FV802250 for example has a larger fan and moves air up to 920 cubic feet per minute which is more than twice what the Ventline Northern Breeze can put out. I have linked a video review for you. view full answer...
The part number that was provided is actually for the screen, # BVD0434-31, which is included with some Ventline roof vents. To obtain the part number for the fan you will need to remove the screen.
I have attached a set of installation instructions which cover the Ventline Ventadome Trailer Roof Vent w/ 12V Fan, # V2094SP-30, as well as a few other models. If your model is not listed on the instruction sheet, please feel free to send me an email with your model number and I will get the... view full answer...
I have a solution for you.
You can use the Metal Low Profile Replacement Cover # BV0534-00 to replace the plastic dome on the Ventline Ventadome Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White # V2094SP-30.
They are compatible and will work just fine. view full answer...
This Replacement Operator, Knob and Screw for Ventline Ventadome Trailer Roof Vents # BVD0462-00 is designed to fit Ventline Ventadome roof vent models # V2092, # V2094.
If you do not have one of those roof vents, I cannot safely recommend you permanently modify the # BVD0462-00 in any way to accommodate your roof vent.
The Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent # BVD0449-A01 is a roof vent that is confirmed to work with the # BVD0462-00 that you referenced.... view full answer...
I am sorry to hear about that. We do offer a couple of replacement parts for the V2094 powered vent. The Replacement Operator, Knob and Screw item # BVD0462-00 and the Replacement Fan Blade for Ventline Ventadome Trailer Roof Vents item # BVD0215-00. If neither of these parts are what you are looking for we offer entire replacement assemblies for the V2094. The vent assembly item # V2094SP-34 in smoke and item # V2094SP-30 in white. view full answer...
We do offer a broad range of replacement trailer vent covers for Ventline, Redline and other vent manufacturers. The link provided will take you to our page for replacement covers where you can see all available white plastic covers.
Based on the photo you provided the replacement cover nearest your design is part # BVD0449-A01 from Ventline. Please compare the photo of this part to your original; you will notice the hinge design appears to be identical. This part is an exact replacement... view full answer...
We carry a broad range of Ventline products, complete vent assemblies as well as individual replacement parts, for both of the part numbers you referenced.
For Ventline item V2092 we offer complete vent assemblies, # V2092SP-29 in smoke color and # V2092SP-28 in white. Replacement domes are also available, # BVD0449-A03 in smoke and # BVD0449-A01 in white.
For powered vent V2094 we offer a complete vent assembly # V2094SP-34 in smoke and # V2094SP-30 in white. Replacement domes only... view full answer...
The Replacement Screen Frame with Screen, # BVC0573-31, is designed to fit Ventadome RV roof vents like models # V2092SP-28, # V2110SP-24, # V2094SP-30, or # V2119-601-00.
I went out to the warehouse to take some measurements so you could compare it and the design of the vents listed above with your existing vent to determine if this is the correct replacement part for you. The frame and screen is 13-1/2 inches by 13-1/2 inches. It is about 1-5/6 inches tall when placed upside down on... view full answer...
For some reason I'm not able to open your picture but if it looks just like the one in the answer you mentioned then you have a standard sized roof vent with a continuous hinge. The hinge is a metal hook sort of shaped like "J" that runs the majority of the length along one side. I've attached the picture from the answer page you mentioned.
The correct replacement lid is # BV0554-01 in white or # BV0554-03 in smoke.
For a full replacement vent you can use # V2092SP-28. Or if you want... view full answer...
I do have an option for you but the Replacement Bug Screen part # FVK2034-80 is not correct for your Ventline Northern Breeze Vent nor is the correct replacement available as it has been discontinued by the manufacturer. The only option we can offer you is a new unit, the Ventline Ventadome Trailer Roof Vent part # V2092SP-28 or part # V2094SP-30 with fan. These units will however be a direct replacement for the Northern Breeze Vent you have now. The screen is also replaceable using the... view full answer...
The Phillips V2094 you referred to is the same as the Ventline Ventadome # V2094SP-30 and we do carry screens for this vent, in two colors.
The part number for Birch White is # BVC0573-31
The part number for Polar White is # BVC0573-41
These include the screen frame and screen; I've added links to video reviews of both parts for you to take a look at. view full answer...
Highest quality rv vents and fans for the best price.
Our Lowest Price Pledge ensures you will never overpay for the parts you need.
Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.
Most detailed, accurate rv vents and fan information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.
Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.
Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.
Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.
Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.