Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide

See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Recommended Trailer Hitch for a Thomas Saf-T-Liner School Bus
  The best option to add a hitch to your 2006 Thomas Saf-T-Liner School Bus is going to be the Curt Class 5 Universal Weld-on Hitch w/ Brackets item # C97CR. This is a universal hitch that fits frames from 18" to 62" wide. This is our highest rated universal hitch and it has a 20,000 lbs towing capacity. The included brackets will drop of 9" from your bus's frame. There are no custom fit hitches for your Thomas Sf-T-Liner and this is going to need to be welded to your frame for the capacity...
  view full answer...
• Can A Hitch Extender Be Used With A Front Mount Trailer Hitch To Park A Travel Trailer
  Hi Don, Hitch extenders place a lot of stress on the hitch because you're leveraging the weight further out so using one typically drops the capacity by 50% when towing. You'd be doing it in a parking lot situation where you wouldn't really be traveling much just more so maneuvering around so realistically that shouldn't affect you but depending on how much weight you're leveraging there could be a breaking point, we just wouldn't be able to know exactly what that point is. The Curt...
  view full answer...
• Trailer Hitch Option For 2017 Ram Promaster 3500 Cab & Chassis
  For your 2017 Ram Promaster 3500 cab and chassis service body, you'll need a weld-on hitch. There are three options from Curt that will work with frames that measure up to 44 inches (from outside to outside), with the only difference being the drop they provide (the distance from the bottom of the frame to the top of the receiver - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt Class 5 Universal Weld-on Hitch...
  view full answer...
• Will The Draw-Tite Trailer Frame Hitch Receiver Fit A 1974 Chevy K5 Blazer With A Gas Tank Shield
  The Draw-Tite Max-Frame Trailer Hitch Receiver 75129 should fit with any OEM parts but just to be used I went out to the warehouse and measured the hitch. From the back of the crossmember tube to the center of the first bolt hole is 1". The distance between the inside of both mounting ears is 30-1/4". This hitch should sit directly under your frame rails so you can use that 1" measurement to see if the tube will run into interference with your gas tank shield. If this doesn't work then...
  view full answer...
  
• Solution for Class V Hitch on 2011 Fleetwood Expedition Motorhome
  For hitch fabrication we only offer the receiver tube like the # E-11 or # C49511. You would need to take this to a local fabricator and they would be able to fashion a hitch and brackets that will fit your 2011 Fleetwood Expedition Motorhome. The other option would be to use one of the universal Class V hitches we have listed for your motorhome. We have the Curt # C47CR with a 9" drop and the Curt # C99CR with an 18" drop. Both options have a 2" receiver. The # C37CR and # C87CR are...
  view full answer...
• Option For Heavy-Duty Hitch on Motorhome
  Since there isn't a custom-fit option for your motorhome, the only possible option for a heavy-duty hitch would be a universal, weld-on type. There are three options from Curt for frames that measure up to 44 inches (from outside to outside), with the only difference being the drop they provide (the distance from the bottom of the frame to the top of the receiver - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop:...
  view full answer...
• Receiver Hitch for 2007 Newmar Class A Motorhome on Spartan Chassis
  While we do not have a custom fit option for a 2007 Spartan Chassis we do have several options of universal fit. Please note the attached link to the filtered options and let me know what follow-on questions you have. You will need to make measurements to identify which available option fits best, measure from inside the frame beam to the inside of the other frame beam to get the frame width. If you have, for example, a width of 18-44" then I recommend the Curt Class 5 Universal Weld-on...
  view full answer...
• Trailer Hitch With Drop for Ford Chassis With 34 Inch Frame
  We have an option for you, though the hitch you mentioned will not fit your ambulance on a 1996 Ford F-350 cab and chassis. Instead, you need a universal weld-on hitch, and we have the exact one that will work: - Curt Class 5 Universal Weld-on Hitch with Brackets # C47CR This hitch is designed to fit frames between 18 inches and 44 inches, and gives a 9 inch drop from the frame of the vehicle so it will work great for you since you mentioned needing an 8 inch drop.
  view full answer...
  
• Hitch Option For 1996 Pace Arrow Motorhome
  There isn't a bolt-on option that will work so you'll have to use a weld-on hitch for your 1996 Pace Arrow motorhome. One that will fit the frame distance of your motorhome and has a 2" receiver (but is actually a Class V hitch), is from Curt, the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. This is for frames from a minimum of 18" to a maximum of 44" which is exactly the range your frame falls in.
  view full answer...
• Recommended Hitch for a 2011 Itasca Suncruiser 35P Motorhome
  Yes, there is and you are in luck because there is a custom fit option. The Curt Trailer Hitch item # C14082 will bolt directly to the frame of your 2011 Itasca Suncruiser 35P. This is a class IV hitch with a 2" receiver. It has a 10,000 lbs towing capacity and a 1,000 lbs maximum tongue weight. The Curt Trailer Hitch item # C14082 fits frames that are 34" wide. It also does require drilling as there are no predrilled holes for a hitch. If your frame is wider than 34" you will need to...
  view full answer...
• Front Mounted Trailer Hitch Options For A 2024 Jeep Wagoneer
  Hi Stephen, There isn't a custom-fit front hitch available but we do offer adjustable-fit weld-on trailer hitches that you can cut to fit your frame and weld in place. We offer a variety of drops so you'll want to do a bit of measuring on your Wagoneer to figure out the best drop to fit the receiver tube either through fascia or beneath it. Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...
• What Hitch do You Recommend for My 2012 GMC Savana Utility Van?
  Is the steel step bumper you have installed the factory bumper on your 2012 GMC Savana KUV Van?
  view full answer...
  
• Option For Trailer Hitch For Holiday Rambler Motorhome
  There is possibly an option for a trailer hitch that fits your 2004 Holiday Rambler, and I say possibly because while a custom fit hitch is not available, there are universal weld-on hitches. This depends on the width of your frame from outside to outside, so if your frame measures up to 44 inches (from outside to outside), you can use any of the following. - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt...
  view full answer...
• Replacement Trailer Hitch Options for a 2008 Coachmen Cross Country 38' Motorhome
  The mounting brackets on the Curt Class 5 Universal Weld-on Hitch # C47CR do need to be in that upright position so while this hitch can technically fit with your motorhome chassis, you'll need to get creative on how to properly weld the brackets to the frame. For an alternative option with the brackets that are in the same orientation as your frame brackets I recommend the Multi-Fit Motorhome Trailer Hitch # 5350 which fits 24" - 46" wide frames and is rated for 5,000 lbs towing. If...
  view full answer...
  
• Trailer Hitch Receiver Options For A 1999 Saab 9-3
  Hey Bruce, We unfortunately do not offer a custom fit hitch for a 1999 SAAB 9-3. You would have to go with a weld-on hitch and figure out the correct drop to clear the rear fascia. We don't have any schematics for this so I recommend reaching out to a local fabrication/welding company to determine the best fit/mounting points. We offer the following weld-on hitches: Draw-Tite 7" Drop # 41990-07 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903
  view full answer...
• 2006 E-450 Super Duty Shuttle Bus Trailer Hitch Receiver
  For your 2006 Ford F-450 Shuttle Bus you are going to need to use a universal hitch. For this you will need to measure how wide your frame rails are apart on the rear of your bus. Then you will need to know how much drop from the frame rails to the bottom of the bumper is required for the hitch to fit. The Curt Class 5 Universal Weld-on Hitch # C47CR will fit frames that are 18"-44" wide and brackets have a 9" drop. The Curt Class 5 Universal Weld-on Hitch # C99CR will also fit frame...
  view full answer...
• Solution for Spare Tire Carrier on 1977 GMC Motorhome
  The # TR-2 fits 4" square and 4-1/4" square bumpers. This and other carriers like it will not fit your 1977 GMC Motorhome, but I do have some other options. The first is to mount the Buyers Products Truck Spare Tire Carrier for 19-1/2" Rims or Smaller # 3375201010 on the back. This can either be bolted on (drilling will be required) or welded on. The other option is to use a hitch mounted spare tire carrier like the # e98ZR. Of course this will require you to have a trailer hitch receiver...
  view full answer...
• Do You Carry a Bike Rack that Will Fit a Heavy Fat-Tire Electric Bike on a Motorhome or Fifth-Wheel?
  Yes! For an electric bike carrier that will accommodate fat bike tires and the torque on the rear of a motorhome and fifth-wheel trailer, I recommend the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount # HLY64FR. The RV Rider has an 80-pound per bike weight capacity and can hold fat tires up to 5 inches wide. In addition, the RV Rider is constructed with bolstered steel that is manufactured to withstand the extra torque. If you need a hitch receiver...
  view full answer...
• Is There A Front-Mounted Trailer Hitch Receiver For A 2021 Ford Ranger
  Hey Charles, There are no custom-fit front-mounted trailer hitch receivers available for a 2021 Ford Ranger but you can still go with a weld-on adjustable-fit hitch. You'll just need to measure the distance from the frame down to the space between the grill and bumper. We offer the follow drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...
• Trailer Hitch Options For A 2001 Blue Bird TC2000 Bus
  Hey Mike, Since there isn't a custom fit hitch for your bus you'll need to go with an adjustable fit weld on hitch. We offer a variety of drop lengths, which I've listed below, to help get the receiver tube at the right height: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...
• Front And Rear Mounted Trailer Hitches Needed For A 1991 Born Free Motorhome On A Ford E-350 Chassis
  Hey Dale, There unfortunately aren't any trailer hitches confirmed to fit so you would need to go with a weld-on, adjustable-fit trailer hitch and measure from the frame down to the bottom of the fascia to determine how much of a drop you need to clear it. This is going to be the case for both the front and rear hitch. We offer the following drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18"...
  view full answer...
• Trailer Hitch and Wiring Needed for a 2022 Ford E-350 Van
  Thank you for reaching out! It looks like the 2022 Ford E-350 doesn't have an exact fit trailer hitch so you'll need to install a universal hitch like the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR and then universal wiring like the 4-Way # 119178KIT or 7-Way # 22551. This isn't really ideal but it's the only way to get a hitch on your vans. Unfortunately the hitches designed for an F-350 frame won't work with an E-350 van frame so this is all going to be custom work that...
  view full answer...
• Hitch For 1993 Ford E-350 RV With 42 Inch Frame
  Thanks for the frame dimensions, and while there are hitch options for your 1993 Ford E-350 RV, I checked with the hitch manufacturers and there are no custom fit options. So what that means is in order to add a hitch to your RV, you would need a universal weld-on hitch. There are three different options, with each of them being Class V hitches with a 2 inch receiver, and fit frames that are between 18 inches and 44 inches wide, so they will fit your '93 E-350's 42 inch frame. The difference...
  view full answer...
• Is There a Aftermarket Trailer Hitch Receiver For a 2006 Toyota Tundra With Factory Tow Package?
  That is correct. I do not currently see any aftermarket receiver which will replace your factory receiver on your 2006 Toyota Tundra. To use an aftermarket custom fit receiver you would have to source a rear bumper and support which fits a Tundra without a factory receiver. You could also use a Weld-On Receiver # C47CR and have it custom mounted to your frame. To do this you will want to visit a fabrication shop first to determine they will be able to complete the installation.
  view full answer...

Do you have a question about this Heavy Duty Receiver Hitch?