Replacement Electric Jack Switch with Harness for Lippert High Speed Stabilizer Jacks
(111 reviews)
Price: $67.42
Replacement Electric Jack Switch with Harness for Lippert High Speed Stabilizer Jacks
Retail:$94.17
Our Price: $67.42
You Save: 28%
Orders above $99 qualify for Free Shipping
Need help with installation?
Locate installers near meCustomers prefer these similar products
- All Info
- Reviews (111)
- Q & A (54)
- Videos (1)
- Photos
- Why etrailer?
Lippert Accessories and Parts
- Trailer Jack
- Camper Jacks
- Switch
- Lippert
Replaces the extend/retract switch and wiring harness for your Lippert electric stabilizer jack (LC363284).
Features:
- Replaces the extend/retract switch and wiring harness for your Lippert electric stabilizer jack (LC363284)
- IP66 rated switch
- Black color
- Quantity: 1 switch
387874 Replacement Electric Jack Switch with Harness for Lippert Components High Speed Stabilizer Jacks
Item # LC387874
Video of Replacement Electric Jack Switch with Harness for Lippert High Speed Stabilizer Jacks
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Lippert Components Trailer Jack LC387874 Review
Today we're going to be taking a look at the replacement electric jack switch with harness for Lippert components high speed stabilizer jacks. This is going to replace the extend retract switch for your Lippert electric stabilizer jack, part number LC363284. It's going to feature a rating of IP66, which makes it a nice weather resistant unit. It's got a sealed design on the back side, so it's going to do a great job at protecting the internal components from dirt, dust, grim and moisture. The unit is black in color. On the back side it also has a foam gasket.
That's going to help create a tight seal at the mounting surface. You can see that it has all the wires coming out of it, so you can easily get it connected to control the jack. Few measurements to go over with you. Measuring this direction edge to edge it's going to measure 2 and 1/4. Going this direction edge to edge it's going to measure about 3 and 1/4 to 3 and 5/16 of an inch. You'll notice it has all the pre-drilled mount holes on it.
Mounting hardware not included. The unit's very easy to control and operate. It's got the textured surface right there on the push area. It makes the switch very easy to control and operate. With this part number you're going to get one switch with the wiring.
That's going to do it for today's look at the replacement electric jack switch with harness for Lippert components high speed stabilizer jacks.
Customer Reviews
Replacement Electric Jack Switch with Harness for Lippert High Speed Stabilizer Jacks - LC387874
Average Customer Rating: 4.9 out of 5 stars (111 Customer Reviews)
Replaces the extend/retract switch and wiring harness for your Lippert electric stabilizer jack (LC363284).
- LC387874
Jerry - 06/06/2020
by: Jerry06/05/2019
Ordered a pair of stabilizer switches (needed one, but replacing both was a better option). Parts were not immediately in stock, but that was not a problem. Within a couple of days, the parts were shipped and everything now works as it should.
Comments
Still good... Works like new.
Jerry - 06/06/2020
- LC387874
Ronald - 08/25/2021
by: Ronald08/24/2020
Had to make a MINOR adjustment to my trailer (Rockwood Ultralite) (existing opening a tad too small) but all in all an easy install. Switches seem solid and well built. Screw holes lined up perfectly.
Comments
Still going strong!
Ronald - 08/25/2021
- LC387874
Diann - 07/23/2018
by: Diann07/23/2017
It was really easy to order and receive these switches! These replacement switches are far better than the ones the dealership wanted to install. They are also better than the ones my unit came with. The switches have this hood on them on the front side that help to protect them from the weather. They are also sealed on the back side. I just replaced one wire at a time and used the wire nuts I had on hand. They work beautifully.
Comments
Still completely satisfied!
Diann - 07/23/2018
- LC387874
Wire t - 11/03/2020
by: Camper M11/02/2019
Excellent product as a replacment stabilizer jack control. Original switch had terminals exposed to water and salt thrown up by tires. This is a potted weather resistant face and waterproof rear panel. Simple to splice wiring harness. Installed 1 year ago.
Comments
One year later and 40 or 50 uses later, these switches continue to perform well! The true test is how they tolerate the locked rotor current if the operator holds the button at end of travel causing 5x the current draw of normal motor operation. I always observe and allow the jacks to coast near the end, then tap until seated.
Wire t - 11/03/2020
- LC387874
by: Chad F06/02/2021
Had to go through testing each wire to find out where they went. Dealership use all the same color wire hahahaha! But this switch was worth it! More sturdier than the dealer one, more waterproof, just had to enlarge the hole a bit to make it fit!!
- LC387874
by: Jim05/10/2021
etrailer is my go to place. They always have what I need and their customer service is amazing. They follow up on every order to make sure it’s received by the customer. What else could you ask for? GREAT PEOPLE TO WORK WITH. A Big Thank You.
- LC387874
by: Alice04/24/2021
Replacement switch for leveling jack asm old one wouldn’t toggle.Installed switch problem solved.
- LC387874
by: Greg07/28/2020
I see the product has been improved from the last three i have replaced, these switches were not exterior friendly, it appears the have been modified slightly to prevent water from entering the internal parts of the switch.I gave a five star review due to the availability of having it and the prompt delivery at these tough times. Thank you E-Trailer. I am looking forward to continuing doing business with you.
- LC387874
Gary R - 09/28/2018
by: Gary R09/28/2017
Received the new switches in the promised time window quoted. The switches appear to be better constructed than the old switch. The old switch failed when the blue wire came loose from the plug terminal which. This plug connected to the rear of the switch. I see the new switch has the terminal plug and switch as one assembly and the wires appear to be hot epoxy sealed. The rain shield appears to be a good idea as well.
Comments
Very good no further problem
Gary R - 09/28/2018
- LC387874
Hilda - 04/09/2019
by: Hilda04/09/2018
This switch was a direct replacement for the rear stabilizers on my 2016 Keystone Sprinter 5th wheel camper. The only difference between the original and this is the rain/shield of the rocker switch. Shipping was super quick and came in great shape. No instructions needed same wire colors, just hook up the same way you remove the faulty factory one.
Comments
Working just fine would recommend this product
Hilda - 04/09/2019
- LC387874
Sean - 03/13/2019
by: Sean03/13/2018
Switch is a perfect fit replacement for the landing gear control on my Jayco HT fifth wheel. The stock switches both broke within three years of buying it brand new. This switch is the exact same wiring and operation as the stock switch but feels more sturdy. We will see how long it lasts! Great customer service and quickly shipped.
Comments
Great!
Sean - 03/13/2019
- LC387874
by: Dana06/27/2018
Got this switch for our brand new travel trailer one year ago. The switch stopped working unexpectedly and our jacks on our camper wouldn't retract or extend. etrailer.com had the best price after I shopped around, had very quick shipping and installation wasn't difficult (step by step instructions provided on website and online). Thanks very much to etrailer.com for saving our camping season! My Husband was very happy with the purchase. To be honest it was so well priced and easy to install with the instructions etrailer.com supplied, we didn't drop the camper off at the shop to have it fixed (under full warranty) ... like I said they saved our camping season! I will buy anything else like this in the future from etrailer.com! Excellent Purchase!
- LC387874
by: Pat G10/10/2017
Installation was relatively painless (except for the hot sun shining on me that the shade canopy didn't cover!). I was replacing an original switch that was not sealed and eventually the elements killed it. It pretty much came apart in my hand when I removed it. This new unit is well sealed. I had to cut out a slightly larger hole to fit the new switch; otherwise the four screw holes lined up perfectly with the original. The wiring was simple enough, except that Murphy dictated that I would have only 3 male connectors of the right size in my work shop, but some serious scrounging turned up another, sparing a trip to the store. I had a pretty good guess how the wires should connect, but going with the old saying, 'when all else fails, read the manual' I took a look at the wiring diagram provided here before starting. It worked. The original switch was white/tan and the new one is black, but the original screws had white heads, so for aesthetics, I will need to replace them with black screws, or hit them with a dab of paint when I am motivated to do so....
- LC387874
by: Raymond05/29/2021
Worked great, only problem is I had to enlarge mounting hole from stock size.
- LC387874
Billy H - 08/07/2020
by: Billy08/07/2019
Matched original part. Easy to install and works perfectly. Thank You!!
Comments
Still works great. I love it. Thanks!!!!!
Billy H - 08/07/2020
- LC387874
by: jhf06/29/2017
Switch for lippert jacks . Replacement part seems to be an upgrade from the original with a rain shield over the top of switch . Front jack switch failed and I ordered the replacement from etrailer . By the time I had received that replacement switch and installed it the rear jack switch went out . So etrailer got another order from me . Both factory switches failed after about 1year of service on a new camper . etrailer has good customer service and prompt shipping when the parts are in stock . I have no complaints and will use them again . In fact I just did to order the second switch!
- LC387874
by: Dave09/01/2018
The electric jack switches I purchased work perfectly. I replaced both original switches even though only 1 was defective (an ounce of prevention... etc.). The only problem that I encountered was that the original switch was round (where it fits into the side of the trailer) and this replacement was rectangular. I used a fine tooth saw (fiberglass siding) to carefully cut out a rectangular shape to fit the switch and then filed it smooth. I used a pure silicon sealant to make sure that there would be no water leaking in. The electrical connections were very easy to figure out and to complete. Give this one a 5 STAR rating.
- LC387874
Vern - 06/15/2019
by: Vern06/02/2018
The only thing bad about the whole thing there was no wiring diagram. My jacks are Bal and they wire different, so a diagram would be nice. The switch works fine.
Comments
The switch works like it should. Very satisfied
Vern - 06/15/2019
- LC387874
Woody F - 08/01/2020
by: Woody F07/31/2019
Great product , fast shipping and very helpful people will buy more from etailer. Item fit perfect had it replaced very quickly Thanks etrailer
Comments
Still doing great !!
Woody F - 08/01/2020
- LC387874
by: Mac04/27/2020
Great replacement switch for the Keystone RV stock they put on their units. If your RV has one without the rain hood, water will get in the electronics and shut down your motor stabilizers. These have the rain hood over the switch and is a much better design.
- LC387874
by: Gary07/03/2017
A switch that Lippert said they could not sell to me. Great product. Exact replacement for my stabilizers. I'm so impressed with the communications from etrailer that I just ordered another one for a spare. Thanks etrailer for a great product.
- LC387874
by: jeff b.07/03/2017
this was a direct replacement for the stabilizer switch that was installed on my 2015 cruiser 5th wheel . I like the new design. the shroud above the switch will help with keeping the water out of the switch.
- LC387874
by: Oldmanshu08/16/2020
Purchased to replace a stock toggle switch that leaked and shorted, biting out a jack motor. Easy to install and waterproof, highly durable compared to failed toggle.
- LC387874
by: Patrick L02/16/2019
Arrived within estimated delivery time. Appears to be of very good quality with sealed construction. Great 'rain' guard over switch is an excellent idea. Only issue I had was too enlarge the opening of the installation hole a little bit to accommodate this new replacement switch. So far so good! Thanks!
- LC387874
by: Chuck05/30/2018
This is a waterproof electric jack switch that replaced a non-waterproof electric jack switch that only lasted 2 years. Easy to install and great price.
29
115
Show More Reviews
Ask the Experts about this Lippert Accessories and Parts
- Troubleshooting Ripped Out Wires on a Lippert StabilizerThere is usually an in-line fuse with wiring that leads up to the battery. The best thing to do first is to disconnect the system from your battery for about 10 minutes and then reconnect. This will serve the same function as a reset button. If this doesn't solve the problem, let me know and I will help you further. If it turns out to be something with the motor, we do have a replacement motor and gearbox for your PSX2 Stabilizer. It's part # LC759091.
view full answer... - Where are Circuit Breakers/Fuses Installed on Lippert Electric Stabilizer JacksThe Lippert stabilizer jacks like you have use an 6 amp auto reset circuit breaker and a 20 amp fuse or breaker. If you check out the diagram I attached you'll see how it normally would be wired. For a 20 amp breaker you'd need the part # PK54520 and for a 6 amp breaker part # LC134181. If somehow the motors are bad they are part number # LC138445.
view full answer...![Image 1 for]()
- Wiring Diagram for the Replacement Electric Jack Switch with Harness # LC387874Yes, I have attached the wiring diagram of the Replacement Electric Jack Switch with Harness # LC387874 for you to reference. Basically the Blue wire goes to a 6A auto reset breaker, like part # LC134181, which then goes to the positive circuit for extending, the Yellow goes to the positive circuit when retracting, the Red wire goes to the positive battery terminal, and the Black wire goes to the negative battery terminal.
view full answer...![Image 1 for]()
- Fuse and Breaker Locations on Lippert Power Stabilizer Jack for Forest River Trailer On the Lippert Power Stabilizer Jack # LC298707 for your Forest River Evo Trailer Trailer there should be a 20 amp (or higher) fuse/breaker located inline with the red power wire coming from the switch before it reaches the battery. Check to make sure the fuse is in good condition and replace if needed. You can also check the 6 amp auto reset breaker that is located inline with the red wire from the switch that goes to the jack's motor. If you find it needs to be replaced you can use...
view full answer...![Image 1 for]()
- Is 6 Amp Fuse for Lippert Stabilizer Jack WaterproofThe 6-amp auto reset breaker included with the Lippert Power Stabilizer Jack # LC298707 (which can also be obtained separately with part # LC134181) will do a good job of resisting damage from the elements but it's not completely waterproof. To ensure a long lifespan of the breaker I do still recommend trying to find a location where it's protected a bit from excess water during storms, etc. Technically you should be able to run common wires like you mentioned as long as you still have...
view full answer...![Image 1 for]()
- Wiring Switch of Lippert Components High-Speed Power Stabilizer JackI was unable to find your order number but I assume you have the Replacement Electric Jack Switch with Harness # LC387874 for your Lippert Components High-Speed Power Stabilizer Jack # LC298707 as this jack will have black and red wires that the switch connects to. To wire it you can follow the diagram I added from the jack manual. The black wire of the switch goes to the negative battery terminal, the red wire goes to the positive terminal through the jack's 20 amp breaker, the yellow...
view full answer...![Image 1 for]()
- Compatibility of the Lippert Stabilizer Jack Switch on a 2015 Forest River Cruise Lite JacksIf your current switch on your 2015 Forest River trailer has 4 wire setup, then the Lippert Replacement Electric Jack Switch with Harness, # LC387874, will work for your application. The following wire colors will connect to your trailer's jack functions: Red goes to positive battery post. Black goes to ground. Blue goes to positive when extending. Yellow goes to positive when retracting.
view full answer...![Image 1 for]()
- Replacement Motor for Lippert High-Speed Power Stabilizer Jack # LC298707For just the motor that is used with the Lippert Components High-Speed Power Stabilizer Jack # LC298707 you will use part # LC352338. This is the upgraded motor that provides faster operation for easy leveling. I have attached a short video demonstration on the Lippert Stabilizer Jack that you can also check out.
view full answer... - Replacement Pins for Lippert Electric Stabilizer Jack I believe you are referring to the roll pins for your Lippert Electric Stabilizer Jack. If this is the case then we do have the replacements available with part # LC125462 for the 5/32" Roll Pin and part # LC181003 for the 3/32" Roll Pin. I'm not quite sure what you are referring to when you mentioned a coupler. If you are able to email me a picture of this particular part I will be happy to see if it is available.
view full answer... - Replacement Switch for Lippert LCI #198641 Stabilizing JackI did some research and found that the # LC387874 should be compatible with your Lippert Components Jack #198641. To confirm, I recommend that you measure your jack switchplate. Lippert discontinued 2 switches which can be replaced by # LC387874. So, if your switch plate measures 3.25" x 2.25" or 3.625" x 1.625" (see diagram) this should work for you.
view full answer...![Image 1 for]()
- How to Install the Replacement Electric Jack Switch with Harness # LC387874I have attached a diagram that demonstrates how the typical wiring will need to be installed for the Replacement Electric Jack Switch with Harness # LC387874 that you referenced. Black Wire - Ground Battery Red Wire - Power Battery (20A Auto Reset Breaker # PK54520 will need to be installed in-line) Yellow Wire (Retract) - Black Motor Wire Blue Wire (Extend) - Red Motor Wire (6A Auto Reset Breaker # LC134181 will also need to be installed here)
view full answer...![Image 1 for]()
- Can Lippert Electric Stabilizers be Used if a Switch Goes Bad or Power is LostYes, you can still raise and lower Lippert Components Power Stabilizer Trailer Jack Item # LC298707 even if the switch goes bad or electrical power is lost for any reason. In order to operate the jack manually there are a few steps: First always disconnect the battery from the system prior to manually operating the system. Failure to disconnect the battery can cause electricity to backfeed through the motor and cause serious damage to the system as well as void the Limited Warranty....
view full answer...![Image 1 for]()
- Does the Lippert Components Power Stabilizer Jack Part # LC387874 Include a SwitchThe Lippert Components Power Stabilizer Jack part # LC298707 does include a power switch. If you ever need to replace the switch, I recommend using the Lippert Electric Jack Switch with Harness for Lippert Components High Speed Stabilizer Jacks part # LC387874 as this is the confirmed switch needed to activate the jack. Lippert also recommends wiring a 6 Amp Auto Reset Breaker part # LC134181 between the switch and the jack's motor. I have attached a diagram that shows the typical...
view full answer...![Image 1 for]()
- Wire Color Diagram for Replacement Electric Jack Switch LC387874I attached a diagram that shows where each of the wire colors of the # LC387874 go. Red goes to positive battery post. Black goes to ground. Blue goes to positive when extending. Yellow goes to positive when retracting.
view full answer...![Image 1 for]()
- Troubleshooting Switch on Lippert Trailer Stabilizer JackIt might be a bad switch but what you're getting is a little strange. The switch, # LC387874, receives 12 volt power from the battery on the red wire. The black wire is ground and the blue and yellow is the polarity for the rocker switch. The blue is the one that is fuse protected to the motor.
view full answer... - Installing Replacement Electric Jack Switch for Lippert High Speed Stabilizer JacksThe Electric Jack Switch with Harness for Lippert Stabilizer Jacks # LC387874 referenced in your question will have 4 wires coming from the unit. The blue wire from the switch will go to a 6 Amp Auto Reset Breaker # LC134181 that will be installed between the switch and the jack motor. The yellow wire will be connected to the black wire coming from the stabilizer jack. The red wire will go to the positive battery terminal and the black wire will go to the negative terminal for ground....
view full answer...![Image 1 for]()
- How to Wire Lippert Replacement Electric Jack Switch # LC387874There will be 4 wires coming from the Lippert Replacement Electric Jack Switch # LC387874 that you are looking at. The blue wire from the switch will go to a 6 amp breaker like # LC134181 that is installed between the switch and jack motor. This will go to the positive circuit on the jack when it is extending. The yellow wire will go to positive circuit when retracting. The red wire will go to the positive battery terminal and the black wire will go to the negative terminal for ground....
view full answer...![Image 1 for]()
- Troubleshooting Rear Stabilizer Jack Not Getting PowerIf power is not actually making it to the rear jack on your trailer's leveling system then I recommend inspecting the wiring along with making sure the battery you're using is fully charged. Visually inspect the wiring to make sure there aren't any exposed, pinched, or damaged areas that need to be replaced. Also make sure your ground is securely attached to a clean bare metal surface without any corrosion or debris. Since you do sometimes get power back to the jack momentarily a bad/weak...
view full answer... - Can You Get the Lippert Electric Stabilizer Jack Without the Motor?The Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707 or # LC369774 only come with the motor. You can get a replacement motor and replacement arms but the main support beam and legs are not replacement parts available. If you want a similar style jack without a motor you can use the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs # UF39-941704.
view full answer... - Troubleshooting Powered Trailer Jack That Does Not Extend or RetractThe problem you describe does sound like a case of insufficient power to the jack motor. The fact that you found corrosion built up inside the fuse holder suggest that there could be similar issues elsewhere, with the battery cables, ground connection or other electrical junctures. You could also have a battery that simply does not any longer have the necessary power to operate the jack motor when it is under load. When the battery that powers a jack is weak, either not fully charged...
view full answer... - Checking Fuses of Electric Stabilizer of 2020 Palomino Puma If you have a Lippert stabilizer jack the 6 amp circuit protection you mentioned is actually a breaker that auto resets. It would be the 20 amp fuse that would need to be checked. Trace the power wire between the switch and the battery and pull out the fuse from the holder and see if the fuse is still good and replace as needed.
view full answer...![Image 1 for]()
- How To Install the Replacement Electric Jack Switch LC387874I am not really sure what you are asking but I have attached a wiring diagrams of the Replacement Electric Jack Switch part # LC387874 for you below. I have also attached the function of each wire below as well. Black Wire - Ground Battery Red Wire - Power Battery Yellow Wire (Retract) - Black Motor Wire Blue Wire (Extend) - Red Motor Wire
view full answer...![Image 1 for]()
- Replacement Switch for Lippert Power Stabilizer Jack Model 198641The correct replacement switch for your Lippert Power Stabilizer Jacks Model 198641 is the Replacement Electric Jack Switch with Harness for Lippert Components High Speed Stabilizer Jacks part # LC387874. In regards to the auto resetting circuit breaker, this is not provided by Lippert and will need to be sourced elsewhere like from a local automotive parts store.
view full answer... - Electric Jack Replacement SwitchI have linked the page to all of our electric jack switches. They are all made the same basic way so you are looking at the location and style for a replacement. If you know the brand of your jack, that will also assist. To test if the switch is bad, you can simply bypass it by connecting the wires. There will be one power wire to the motor to extend and another one to retract and you of course will also need to connect a ground wire to the frame. This will let you know if your motor...
view full answer... - Available Replacement Landing Gear SwitchReplacement switch # LC387874 would work for you if you have the Lippert electric stabilizer jack 363284; it is the replacement switch for that jack.
view full answer... - Clicking When Raising Trailer Electric Landing GearThere are a few things to look at that could be your issue. Since your batteries are fully charged, I would suggest looking at it piece by piece. To get you proper parts, I need to know the manufacturer of the landing gear and any info about the trailer you can give me. In the meantime, have you attempted to adjust the legs with the manual crank? If that works, some of the possible issues may be weeded out. Start by disconnecting your motor from the gear box. Run your motor for...
view full answer... - Replacement Switch for Lippert Electric Stabilizer JacksYes, you can use replacement switch # LC387874 with your Lippert stabilizers. This switch actually replaces several of the old switches as well as new ones so with it you are good to go.
view full answer... - Troubleshooting Electric Tongue Jack Not Receiving Power After Replacing Fuse It sounds like the switch on your electric tongue jack might have been damaged as well when the fuse blew. You can test this by simply bypassing the switch and connecting the wires directly to your power source. There will be one power wire to the motor to extend the jack and another one to retract. Also make sure you connect the ground wire to the frame. This will let you know if just the switch is bad or if there is something going on with the jack itself. We do have a nice selection...
view full answer... - Wire Gauge for Extending Wires of Replacement Electric Jack Switch # LC38787412 gauge wire would be what you'd want to use to extend the wires of the Replacement Electric Jack Switch with Harness for Lippert Components High Speed Stabilizer Jacks # LC387874.
view full answer... - Is Button Available For Forest River Heritage Glenn Landing GearUnfortunately the button is not sold as a separate item and you will need to replace the switch. I have attached a photo of the # LC387874 you mentioned. The photo also shows what the wires are used for.
view full answer...![Image 1 for]()
Do you have a question about this Accessories and Part?
Why etrailer.com?
At etrailer.com we guarantee:Highest quality accessories and parts for the best price.
Our Lowest Price Pledge ensures you will never overpay for the parts you need.Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate accessories and part information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Installed by:
Cole B
Written by:
Wilson B
Updated by:
Mike S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 800-298-1624
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.