Replacement Landing Gear Legs for 1995 Jayco Designer Series 5th Wheel Trailer
Updated 08/19/2020 | Published 08/06/2018
Products Featured in This Question
Question:
I have a 1995 Jayco Designer Series 3210RLR fifth Wheel camper that I am needing to purchase landing legs for. The gears have worn out and I have discovered the replacement gears are no longer available. The legs are bolt on and have the electric motor. What legs will work with this camper.
asked by: Bruce W
Expert Reply:
It looks like your 1995 Jayco Designer Series 5th Wheel Trailer was equipped with an Atwood landing gear system. Atwood was recently bought out so their products are getting harder and harder to find.
To replace both the legs on your system the Lippert # LC179013 Lead Leg and # LC179014 Follow Leg should work great. These feature standard weld stop measurements of 15-1/2 inches from inside to inside and 17-1/2 inches from outside to outside. You will just want to compare this to your existing brackets to make sure these will bolt right up without any modification. I have attached an image to clarify this.
I have attached a couple short video demonstrations that you can also check out.
Product Page this Question was Asked From
Follow Jack Repair Kit for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Repair Kit
- Stromberg Carlson
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Q&A: Replacement Landing Gear Legs Needed for a 2004 Arctic Fox 29.5E 5th Wheel Trailer
- Q&A: Does the Weigh Safe 180 Hitch 2-Ball Mount for 2.5" Hitch WS74MR Fit a 2-1/2" Receiver?
- Video: Weigh Safe 180 Hitch 2-Ball Mount In-Depth Review
- Shop: Replacement Motor for Solera Power RV Awnings Manufactured before 2015
- Shop: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Replacement Motor for Solera Power RV Awnings Manufactured after 2015
- Q&A: What Replacement Lead Leg Do I Need for My 2011 Keystone Montana Trailer?
- Q&A: Difference Between LC179013 & LG-179013 Landing Gear Legs
- Q&A: Recommended Replacement Awning Motor for Lippert Solera Awnings
- Q&A: Wiring Installation of Kwikee Step Control Unit
- Search Results: 5th wheel landing gear
- Shop: Replacement Motor for Kwikee Electric RV Steps - 12V
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Search Results: landing gear
- Q&A: How Much Does The BulletProof Hitches Aluminum Adjustable 2-Ball Mount - 2-1/2" Hitch Weigh?
- Search Results: pintle hitch ball trailer hitch ball
- Search Results: built~in pintle hook trailer hitch ball mount
- Search Results: trailer hitch ball mount
- Search Results: landing gear camper jacks
- Video: Lippert Components Trailer Jack LC179013 Review
- Search Results: reese 500708
- Video: Review of Weigh Safe 180 Hitch - WS44MR
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Suspension Enhancement
on Accessories and Parts
Debra O.
8/9/2020
I have a 1997 jayco designer 3510 and atwood 71125 landing gear the gears went out of the legs and there is no replacement gears is there any legs that can be purchased to work with the landing gear.