Landing Gear for a 2009 Heartland Bighorn 5th Wheel Trailer

Question

Question:

Landing gear for 2009 heartland big horn fifth wheel What kind is it and what do you replace it with

asked by: Sandra A

0

Expert Reply:

I did some checking and the 2009 Heartland Bighorn 5th wheel trailers were built on a Lippert chassis and have other Lippert components so the landing gear will also be Lippert. If you just need to replace legs then the lead leg is # LC179013 and the follower leg is # LC179014. If you need the whole set use # LC333964.

expert reply by: Michael H

0

Answer 1

Hey James, thanks for reaching out. Yes I can provide dimensions for the crank handles we carry. Two common ones are the Lippert #LC119226 and the Ram #RVLG-HDL. I have included a picture that shows dimensions of both. Hopefully one of these match…

view full answer...

Answer 2

I went out to our warehouse and measured the rubber grommet piece on the Replacement Strainer Basket for LaSalle Bristol RV Kitchen Sink Drains #34465JNBSK10081 and measured a diameter of 1.8" (4.57 cm). Attached is a diagram showing this…

view full answer...

Answer 3

We do have the measurements for the Replacement Lead Leg for a KeyStone Montana Trailer #LC178653. I went ahead and attached a picture of the dimensions to this answer. Even though this leg has three bumps, it will still work to replace the lead leg…

view full answer...

Answer 4

Hey Johnny, essentially the part #LC122533 and the part #LC179013 are the same as they have the same outer tube length of 29-1/2 inches. The part #LC119102 is for Venture brand landing gear and is still very similar. What brand do you have now?

view full answer...

Answer 5

Thanks for all the information! You are correct that is the lead leg because it is closest to the gear and the motor. However, in order to determine which replacement lead leg you need, you'll need to find the model of the landing gear on your…

view full answer...

Answer 6

The Venture VMC900R is a very common landing gear set so for replacement legs we know you need the part #LC119102 for the lead leg and #LC119101 for the follow leg. Since you are wanting to fix the issue as cost effective as possible I would…

view full answer...

Answer 7

Hello Nick, We will definitely have what you need, but I do not have a database that supplies me with what is put on what camper. In my research I am showing that the Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs #LC179014…

view full answer...

Answer 8

Allen, not much at all - it really depends on which HomePlow or WingMan you go with. The Meyer HomePlow #ME28FR comes with a wired auto-angling controller, but it can also run with Meyer’s optional wireless kit if you’d rather skip the cable…

view full answer...

Answer 9

Yes, it can and thanks for the picture! The electric motor and gearbox can be rotated to the front of the Stromberg Carlson Electric Landing Gear Set item #LG-4. What's wrong with your Venture M-9000-PK landing gear? We have some replacement…

view full answer...

Answer 10

I am not sure what particular replacement switch you are using on your landing gear, but it sounds like it is a 6-terminal switch like the Ultra-Fab #UF38-75-1037. I have spoken with Ultra-Fab in the past regarding this particular switch, and was…

view full answer...

Answer 11

Any powered landing gear or powered tongue jack will draw less power as it legs descend down toward the ground and much more as soon as they make contact and encounter resistance. This is a normal occurrence. In the same way, any jack - even a manual…

view full answer...

Landing Gear for a 2009 Heartland Bighorn 5th Wheel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching