Replacement Landing Gear Legs Needed for a 2004 Arctic Fox 29.5E 5th Wheel Trailer
Published 07/11/2018 >
Products Featured in This Question
Question:
I'm ready to order the new landing gear for my 5th wheel. My weld stop measurements are 19.5 and 21.5 which matches the specs for the LG-4. One question though. This existing brackets that hold the legs do not face (direction of opening/bolt) forward like the pictures show. They both face towards the center of the trailer. Note the attached pics of both legs taken from the front. My current original legs only have weld stops on one of the four sides, and that stop rests against the back of the bracket rather than the side (as shown in the pictures). This has worked on my 2004 5th wheel until now so I assume it will work with these new legs too, but I wanted to run it by an expert before I order.
asked by: Doug C
Expert Reply:
I can give you some information to help you determine if the Lead # LC179013 and Follow # LC179014 legs will fit your 2004 Arctic Fox 29.5E 5th wheel, but we don't really have a database to pull from when it comes to OEM part numbers on trailers.
Both legs have an overall height of 32" with an outer tube width of 2-1/2" and an inner tube width of 2-1/4". The total travel distance is 21" with a 16" drop leg travel.
To determine if these will fit directly to the brackets that you currently have on your 5th wheel you need to measure where your weld stops are. If you check out the attached picture you can see that the weld stop locations for both legs measure 15-1/2" on the inside and 17-1/2" on the outside. If those match up with your current landing gear then these will fit directly to your trailer and new weld stop locations will not need to be installed.
I have linked a review video for the lead leg for you to reference.
Product Page this Question was Asked From
Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Search Results: landing gear camper jacks
- Search Results: trailer hitch
- Search Results: vmc900r
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Search Results: trailer jack
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Q&A: What Replacement Lead Leg Do I Need for My 2011 Keystone Montana Trailer?
- Shop: Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies
- Shop: Lippert Electric Landing Gear w/ Handle - Outside Mount - 34-3/4" Lift - 5,000-lbs
- Search Results: landing gear motor
- Video: Ultimate Overview of the Stromberg Carlson Electric Landing Gear Set
- Search Results: stromberg carlson camper jacks
- Q&A: How to Measure to Pick Out Replacement Landing Gear for a Trailer
- Video: Checking Out the Ultra-Fab Deluxe Electric Landing Gear Set
- Q&A: Replacement Landing Gear for 1998 Carriage Carri-Lite RK 732
- Search Results: fifth wheel landing gear
- Q&A: Replacement Jack Legs for Venture VMC900R Landing Gear
- Q&A: Replacement Landing Gear Legs for Venture Landing Gear
- Q&A: Replacement Landing Gear Lead for 2012 Eclipse Stellar Toy Hauler
- Shop: Brake Controller
- Q&A: Recommendations For Complete Fifth Wheel Landing Gear For 2004 Jayco Eagle
- Video: Feature Review Replacement Follow Leg for Stromberg Carlson Landing Gear
- Video: The Low-Down on the Lippert Landing Gear
- Video: Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor Review
- Video: Lippert Components Trailer Jack LC179013 Review
- Video: All You Need to Know About the Landing Gear Set
- Article: Best Landing Gear







Doug C.
7/11/2018
I'm ready to order the new landing gear for my 5th wheel. My weld stop measurements are 19.5 and 21.5 which matches the specs for the LG-4. One question though. This existing brackets that hold the legs do not face (direction of opening/bolt) forward like the pictures show. They both face towards the center of the trailer. Note the attached pics of both legs taken from the front. My current original legs only have weld stops on one of the four sides, and that stop rests against the back of the bracket rather than the side (as shown in the pictures). This has worked on my 2004 5th wheel until now so I assume it will work with these new legs too, but I wanted to run it by an expert before I order.