Replacement Lead and Follow Legs For Venture VMC900R Landing Gear

Question

Question:

I have a jack that I need to replace. It is the lead leg, part number VMC900R. I see 2 options and Im not sure if one is generic or not as its a different brand and cheaper price. LC179013 and LC119102 Thanks

asked by: Loyd C

0

Expert Reply:

The Replacement Lead Leg # LC119102 will fit your Venture VMC900R landing gear. We also have the Follow Leg # LC119101 available if you wish to replace them both. The Leg # LC179013 you found is for LCI Power Landing Gear assemblies.

expert reply by: Bud M

0

Answer 1

The correct Replacement Leg for Venture 5th Wheel RV Landing Gear is part #LC64PJ for the follow leg and part #LC54FR for the lead leg

view full answer...

Answer 2

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Answer 3

Hi James; the better option would be the Bulldog #BD500162 you were looking at. You can add the Motor and Switch Kit for Stromberg Carlson Landing Gear #LG-217884 to the Bulldog which will give it the same functionality as the #LG-4 while saving you…

view full answer...

Answer 4

For an aluminum gear box that would work well as a replacement for the Venture landing gear you have on your 2006 30.5foot Everest 5th Wheel RV you would want the part #LC276602 that is a confirmed fit.

view full answer...

Answer 5

The 91602 gas regulator you're trying to find was discontinued which is why you're having issues finding it. Since this is the case you'll actually need to replace your entire water heater unit as there aren't any replacement gas…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Lead and Follow Legs For Venture VMC900R Landing Gear

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching