Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…
Thanks for letting us help Stephen. The TecNiq ID Light Bar #TN25TR has mounting holes spaced 8-1/2" apart on center, so unfortunately, it won't work for the mounting dimensions you provided. I looked through the ID light bars we carry and…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…
Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The #AL91RB and #AL91AB will work with the Mounting Bracket #A91BB and then for a pigtail you can use the Right Angle…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…
Thanks for letting us help Stephen. The TecNiq ID Light Bar #TN25TR has mounting holes spaced 8-1/2" apart on center, so unfortunately, it won't work for the mounting dimensions you provided. I looked through the ID light bars we carry and…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…
Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The #AL91RB and #AL91AB will work with the Mounting Bracket #A91BB and then for a pigtail you can use the Right Angle…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Rectangle Trailer Lights from Optronics for clean fits
Dial in a tidy look with rectangle trailer lights from Optronics. Pick what suits your setup, from bright LED options to submersible choices with triangular 3-prong pigtails, or simple two-wire lights where one is a ground wire. For hassle-free swaps, match your light's measurements and the connector style before you order.
Yes, many are made for this—look for a sonically sealed, waterproof housing. To help reliability, fill pigtail sockets with dielectric grease and consider disconnecting lights before launching. If moisture gets in, corrosion can occur, so inspect the housing and seals before use.
Not all—some have just two wires with one ground and won't serve as turn signals. If you need turn/stop/tail, choose lights that specify those functions. Verify wire count and functions before you mount to avoid rework.
They're bright and install is straightforward. Match the wiring to your existing harness and test before final mounting. If your trailer is bolted together, a dedicated ground to each light can help versus a chassis ground. Once wired, they look clean and OEM on many trailers.
Yes, Optronics offers lights with the triangular 3-prong plug. Confirm your harness has a 3-pole triangular connector and choose a matching light or pigtail. If you need a driver's side, check that it includes the license plate light function.
Clearance Lights
Interior Lights
License Plate Lights
Reflectors
Tail Lights
Utility Lights
Filters
