See what our Experts say about this TruRyde Trailer Bearings Races Seals Caps

• Recommended Disc Brake Components for Nuwa Hitchhiker 5th Wheel Trailer Conversion
  For your Nuwa Hitchhiker 5th wheel, I recommend you start with the Kodiak 12" Hub-and-Rotor Assembly - 6 on 5-1/2 # KHR12D. For this assembly you will need the bearing kit # Bearing Kit # BK3-100. For your grease caps you will need # RG04-060 which come in sets. For your calipers, I recommend the Kodiak Disc Brake Caliper - Dacromet# KDBC225DAC along with the mounting bracket # KCMB12D and brake pads # K225CP. For your brake lines and your Electric Over Hydraulic actuator, I recommend...
  view full answer...
• What Size Grease Caps Does the Kodiak Disc Brake Kit # K2HR526DKG Require?
  The Kodiak Disc Brake Kit # K2HR526DKG uses a 2.44" Grease Cap # RG04-060 or EZ Lube Cap # RG04-080. We also have these in the Kits # DBRKHW6 or # DBRKHW6EZ which includes the caps, bearings, seals and lug nuts for the disc brake kit.
  view full answer...
• Options For Upgrading Disc Brakes On A 2005 Eagle Boat Trailer
  Hi Dave! We do have two hub/rotor options that matches your bearings and bolt patter, and I have them listed below. Both are 12" rotors as well, which is what the bolt pattern and bearing numbers you have correspond to. Kodiak 12" Hub-and-Rotor Assembly - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs # KHR12D DeeMaxx 12" Hub/Rotor Assembly - 6 on 5-1/2 - Maxx Coating - 6,000 lbs # DE69VR I do need to note that neither of these include bearings, seals, or dust caps, so I have those below...
  view full answer...
• Replacement Brakes and Hub Assemblies for Lippert 5,200 Pound Axle
  For your trailer the drums you need are # 8-201-5. They're designed to fit bearings # 25580 and # LM67048 with the 2-1/4 inch seal # GS-2250DL. For brakes I recommend # AKEBRK-7-SA. Both the left and right sides are included. They are side specific so you'll want to pay attention to the labels when installing. They're self-adjusting brakes so they'll need to be adjusted when you install them and then never again. The grease cap to fit the hubs is # RG04-080 if you have E-Z lube axles...
  view full answer...
• Finding a Hub for a Very Old Trailer with 6 Lug Bolt Pattern # 1779 inner and # 2788 Outer Bearings
  I did some research and found that the 2,600 lb Hub, # 22834, takes the # 1779 outer bearing and # 2788 inner bearing and would use the # 29031 grease seal. This hub has a 6 bolt on 5-1/2 inch bolt pattern. This sounds like the hub you have, and replacement parts are available. Along with the parts mentioned above you may need grease caps, # RG04-060, and races, # 1729 and # 2729, to complete parts needed to repair one of your existing hubs. When doing my research I found that no other...
  view full answer...
• Converting From Disc Brakes to Electric Brakes on 1977 Airstream Sovereign 31
  In order to verify if this is the correct hub and drum assembly you will need to check the bearing numbers. If the numbers are too worn, you will need to measure using a digital caliper like the # PTW80157. I have attached a photo of where you need to measure on your spindle. We will assume you have this information since you already removed your hub and drum. The Dexter Trailer Hub and Drum Assembly # 8-201-5 is for 5,200 lbs axles and has a 6 on 5-1/2 bolt pattern. This uses a # 25580...
  view full answer...
  
• Replacement Bearing Cover Options for Bri-Mar Dump Trailer
  You will need one of two sizes depending on the axle capacity of your Bri-Mar dump trailer. If you have 7,000 lbs or 8,000 lbs axles, then you will need part # 21-43-1 and # DC-RP if you have EZ Lube spindles (grease zerk on the end) or you can use part # RG04-100 if you have standard spindles. If you have 5,200 lbs or 6,000 lbs axles, then you will want part # RG04-080 if you have EZ Lube spindles or part # RG04-060 if you have standard spindles.
  view full answer...
• Purpose of Grease Caps and How to Measure to Get Correct Size
  The purpose of the grease cap is to protect the bearing and the axle from any dirt getting into the bearing, which would then damage the bearing, hub and axle. So it is a good idea to have caps on your axle. To get the correct size cap you would need to measure the inside diameter of the cap mounting surface on your hub. Then that measurement would match up to the cap size outside diameter. The sizes of caps only vary by a small amount so the measurement has to very accurate. Some of the...
  view full answer...
• How to Remove Dust Cap on Snowbear Utility Trailer
  The dust or grease caps on your Snowbear Utility Trailer should just pop out and in. I recommend using a flat head screwdriver to pry them out or tap them from side to side with a hammer. Then to install new ones, you can just gently hammer them in. If you are still needing replacement grease caps, you will want to measure the inner diameter of the hub where the cap fits. I recommend using a digital caliper like # PTW80157 to get the most accurate measurement possible. For example, the...
  view full answer...
• How to Determine the Correct Replacement Dust Caps for a 2011 Haulmark Cargo Trailer
  To determine the correct dust caps for your trailer you will need to measure the inner diameter of the hub/drum where the cap fits. The measurement has to be as accurate as possible so you will need to use digital or dial calipers. If that measurement is 2.446 inches then cap set # RG04-060 will fit. I also can most likely figure out the correct one by going by the outer bearing number. You will not have to remove the hub/drum to get the number. You should be able to see it by removing...
  view full answer...
• Grease Seals and Dust Caps for AL-KO Trailer Hubs with 25580 and 15123 Bearings
  The most grease seal associated with hubs that use the bearings you have specified is # GS-2250DL for 1 seal or # RG06-070 for a pair. For a grease cap you will likely need a 2.44 inch cap as that is the size associated with the hubs that use the bearings you mentioned. If the spindle has a grease fitting at the end use # RG04-080. If the spindles do not have grease fittings use # RG04-060.
  view full answer...
• Cap Recommendation to Hub Bore 2.44 inches
  The closest cap we have to the size you mentioned woudl be the part # RG04-060 which is designed fit a hub bore of 2.44 inches which would be a tiny bit too big for the dimension you listed. The other sizes we offer are either much bigger or much smaller.
  view full answer...
• Recommended 2" Dust Caps for a 1994 Coleman Destiny Trailer
  From what I could find out about the part number 4714A0621, it looks like it is a 2 inch diameter standard grease cap. So with that being said, the TruRyde 1.988" OD Drive In Grease Cap # RG04-020 will be what I suggest. These will fit your hubs nice and securely.
  view full answer...
• Replacement Grease Cap and Wheel Studs for a RV Trailer Hub with ALKO Electric Brakes
  The grease cap part number that you referenced cross references to a drive in cap with a 2.44 inch outside diameter. If you have a standard cap then the Grease Cap, 2.44 inch OD Drive In, item # RG04-060, is the correct part. If you have a grease fitting in the end of the spindle then the Grease Cap, 2.44 inch OD Drive In with Plug, item # RG04-080, would be the correct part. These parts are correct only if the 092101 part you mentioned is correct. The correct inner and outer bearing part...
  view full answer...
• What Grease Cap Will Fit On The Dexter Complete E-Z Lube Hub and Drum Assembly, # 8-201-5UC3-EZ
  The grease cap for the Dexter Complete E-Z Lube Hub and Drum Assembly, # 8-201-5UC3-EZ, is the TruRyde Grease Cap, # RG04-080. The Fulton Grease Cap, # F001527, will not fit. It is not the right size and it is not made for the EZ Lube axle. If you do not have the EZ Lube axle the TruRyde Grease Cap, # RG04-060 would be the correct grease cap.
  view full answer...
• Which Grease Caps for a 1987 Coleman Sequoria Pop-Up Camper
  You will need to measure the inside diameter (ID) of the cap mounting surface on your hub to match the outside diameter (OD) of the grease cap. You will then be able to select the proper style cap with the proper OD for your trailer hub. You can also find the correct grease cap if you can find the hub assembly part number or the bearing part numbers, inner and outer. the grease seal part number would help also.
  view full answer...
• Grease Caps Available that Fit a 2.44 Diameter
  We do have a variety of grease caps that fit the 2.44 inch diameter that you reference; our selection has been linked for you to filter through. Among the options we have the non-threaded Bearing Buddy Bearing Protectors # BB2441, the threaded option # BB2441T-SS, as well as traditional grease caps for EZ Lube spindles # RG04-080, and non-EZ Lube spindles # RG04-060. Each of these part numbers come in a quantity of 2 and the prices can be found on the product pages. If you are talking...
  view full answer...
• Trailer Hub and Drum Recommendation for Replacing Hub with Bearings 25580, LM67048
  Actually the bearing info you listed indicates you have a very standard number 42 spindle which we have plenty of fits for. Only issue is that you'd need to go with a 6 on 5-1/2 bolt pattern. So for that you'd want the part # 8-201-5 with the bearing kit # BK3-300 and grease cap # RG04-060. Then for brake assemblies part # AKEBRK-7-SA which is a kit for both sides of the axle.
  view full answer...
• Can Double-Lip Grease Seals Be Substituted for Standard Seals
  You can replace a standard grease seal with one of the Bearing Buddy seals like # BB60002, even if you do not care to use the Bearing Buddy protectors, so long as the seal inner and outer diameters match the dimensions required by your spindle and hub bore. These seals are the double-lip type that can withstand the higher grease pressure inside the hub bore when a Bearing Buddy grease cap is installed but they will provide durable service even if this is not the case. They will also work...
  view full answer...
• Which Grease Caps fit Trailer Hub Part # 8-201-5
  For hub 8-201-5 you will need 2.44 inch OD drive in caps. We have several caps available for this size like part # RG04-060, which is a standard cap, or part # RG04-080, which have removable plugs for checking grease or bearings.
  view full answer...
• Parts Needed for Hub and Drum Assembly for Rebuilt Trailer
  If you have hub and drum assembly # 8-174-5UC3, which you referenced, the assembly comes with the bearing sand seals. However, the replacement parts are: # 25580 Inner bearing # 15123 Outer bearing # RG06-090 seals # RG04-060 Grease Cap # 15245 Race # 916N lug nuts The lug nuts won't need washers. We do not sell backing plates separately. If you need backing plates and brake shoes, you are better off pricewise to purchase a new brake assembly like # AKEBRK-7R-SA and # AKEBRK-7L-SA. If...
  view full answer...
• Grease Cap With 2.4 - 2.5 Outer Diameter
  We have an option that is close to the measurements you took with the Grease Cap, 2.44" OD Drive In # RG04-060. While this isn't the exact measurement you have, the 2.44" outer diameter is so close that I at least wanted to mention it as a possible option for you.
  view full answer...
• Recommended Grease Cap That Fits Dexter Axle Trailer Hub and Drum Assembly # 42656
  The grease cap that will work with the etrailer.com Trailer Hub and Drum Assembly, part # AKHD-655-6-K is part # RG04-060. These grease caps have a 2.446 inch O.D. and are made of 22-gauge zinc-coated steel.
  view full answer...

Do you have a question about this Trailer Bearings Races Seals Cap?