What Grease Cap Will Fit On The Dexter Complete E-Z Lube Hub and Drum Assembly, # 8-201-5UC3-EZ

Question

Question:

What grease cap would fit this hub? Would the Fulton Grease Caps - F001527 fit it?

asked by: Wayne S

0

Expert Reply:

The grease cap for the Dexter Complete E-Z Lube Hub and Drum Assembly, # 8-201-5UC3-EZ, is the TruRyde Grease Cap, # RG04-080.

The Fulton Grease Cap, # F001527, will not fit. It is not the right size and it is not made for the EZ Lube axle.

If you do not have the EZ Lube axle the TruRyde Grease Cap, # RG04-060 would be the correct grease cap.

expert reply by: Jeff D

0

Answer 1

Hey David, thanks for the detailed information. For pn 57920 Dexter 5,200 lbs axles you'll need the Bearing Kit item #BK3-300. This kit includes inner/outer bearings, races, grease seal, and cotter pin. They're sold individually so you'll…

view full answer...

Answer 2

Hey Roman, thanks for reaching out! What you're needing is the Dexter's E-Z Lube Grease Cap & Plug Kit #DX87HR which is the exact same as the kit K71-317-00, we just put our own part number to it. Is there anything else you're…

view full answer...

Answer 3

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 4

In order to determine the correct E-Z Lube grease cap for your Dexter axle you are going to need to measure the center of the hub where the grease cap is going to fit. I recommend using digital calipers like the #PTW80157 in order to get an accurate…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What Grease Cap Will Fit On The Dexter Complete E-Z Lube Hub and Drum Assembly, # 8-201-5UC3-EZ

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching