Options For Upgrading Disc Brakes On A 2005 Eagle Boat Trailer
Updated 09/03/2026 | Published 08/31/2026 >
Products Featured in This Question
Question:
I sent an earlier mesg but didnt see a reply. Looking for a hub for 2005 eagle boat trailer. 6-5.5, 1.75/1.25 axel.
asked by: Dave W
Expert Reply:
Hi Dave!
We do have two hub/rotor options that matches your bearings and bolt patter, and I have them listed below. Both are 12" rotors as well, which is what the bolt pattern and bearing numbers you have correspond to.
Kodiak 12" Hub-and-Rotor Assembly - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs # KHR12D
DeeMaxx 12" Hub/Rotor Assembly - 6 on 5-1/2 - Maxx Coating - 6,000 lbs # DE69VR
I do need to note that neither of these include bearings, seals, or dust caps, so I have those below as well:
1.25" Bearing - 15123 - Qty 1 # 15123
1.75" Bearing - 25580 - Qty 1 # 25580
Grease Seal I.D. 2.250" / O.D. 3.376" # GS-2250DL
There are a couple different styles of caps, so you will need to choose the one that matches what you currently have. I have all three styles below:
Grease Cap, 2.44" OD Drive In - Qty 2 # RG04-060
Grease Cap, 2.44" OD Drive In with Plug - Qty 2 # RG04-080
Kodiak XL ProLube Kit for for 5,200-lb to 6,000-lb Axles # XLPROLUBE2440KIT
--This includes oil seals, so you would not need to purchase them separately
Now if you are wanting to upgrade your current disc brakes, the DeeMaxx Disc Brake Kit - 12" Hub/Rotor - 6 on 5-1/2 - Maxx Coating - 6,000 lbs # DE28YR would be a great option. These are super sturdy and they include everything you need to upgrade them. Since you have two axles, you would need to grab two of the kits.
However, if you are wanting to do a complete overhaul of the entire braking system and not just the brakes, the Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 12" Rotor - 6 on 5-1/2 - 6K # HYD44VR is what I would go with. This include everything you need for the brakes, all the lines to get them attached, and an electric over hydraulic brake actuator. I like the Hydrastar actuators more than any other currently on the market as they just seem to work the best. And with the most vehicles.
What vehicle are you pulling this with? And where do you typically launch?
Product Page this Question was Asked From
Kodiak 12" Hub-and-Rotor Assembly - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs
- Trailer Hubs and Drums
- Hub with Rotor
- Standard
- 25580 / 15123
- Marine Grade
- For 5200 lbs Axles
- For 6000 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Kodiak
more information >
Continue Researching
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Recommended Disc Brake Components for Nuwa Hitchhiker 5th Wheel Trailer Conversion
- Q&A: Can Two Batteries Wired In Parallel Receive a Charge at the Same Time
- Q&A: Do the Hydrastar Disc Brake Kits Include Kodiak Brakes?
- Q&A: Solution for Replacement Brake Pads for TDE 46304 Caliper
- Q&A: Is There A Lift Kit Option for A Dexter Torflex #13 Axle
- Q&A: Can I Turn or Grind Disc Brake Hub/Rotor to Remove Rust
- Q&A: How to Determine the Replacement Hubs for a 2002 Magic Tilt Trailer
- Article: Trailer Lighting Requirements
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Trailer Tire Sizing
- Article: Trailer Wiring Diagrams
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Determining Trailer Tongue Weight


Dave W.
9/3/2026
Pulling with GMC 2,500 Typically launch 3 mile from the storage unit. Fall Creek on Lake Cumberland